$450 Mige Direct Drive Force Feedback Wheel - DIY Build - Wheel Test
ฝัง
- เผยแพร่เมื่อ 6 พ.ค. 2020
- BUILD VIDEO IS UP!: • $450 Mige Direct Drive...
Octagon*** lol
FULL BUILD TUTORIAL COMING SOON WITH WIRELESS BUTTON BOX!
Direct Drive Wheel Build Thread/Tutorial : www.xsimulator.net/community/...
So after using the AASD servo drivers for my rig and with how cheap you can get them bundles with servo motors i have been wondering if anyone would ever be able to get a Direct Drive FFB Wheel up and running with one.. Then i stumbled upon a post on Hackaday.io and someone had done just that! . Using an STM32F407 Discovery board and running MMOS he was able to achieve this. I then set out to try and build one myself. His post is in Chinese and i had to work with google translate to figure out what was needed but with the help of his pictures i was able to make some sense of it.
Thanks to DIY Sim Racer: / @simracingos
hackaday.io/project/168801-di...
My Build: www.xsimulator.net/community/...
Thanos Controller: www.tindie.com/products/troni...
FlyPT Mover: www.xsimulator.net/community/...
Simtools: www.xsimulator.net/simtools-m...
OBS Studio: obsproject.com/
Thanos Discord: / discord
Xsim Discord: / discord
Peacemakers Discord: / discord
Shoutout to Thanos, the whole Xsimulator community and everyone else sharing their knowledge for making this hobby as great as it is!
Thanos AMC-AASD15A controller
DIY Linear actuators - 80st-m02430 motors
12u Server rack
FlyPT Mover 2.9
Logitech g920 with sparco wheel
G25 clutch pedal analogue handbrake
Sparco fixed back seat
Oculus Rift CV1
Kogan 34" UWQHD 3440x1440 @144hz monitor
GTX1080
i7 8700k
32g ram
Camera: Sony A73 with Tamron 17-28 & 28-75 f2.8
I wish you success in DIY
Amazing work on the motion rig and great to see people enjoying our hobby. Sub well earned my friend
Thanks mate! Now if only i could find more time in my day to enjoy it properly haha :)
@@peacemakermotion3949 Sadly the same for all of us lol
Nice setup on the OSW wheel. I will check out some of your other videos as I like your sim setup !! I have a P3 rig. I have a few videos posted.
Thank you for adding my tutorial in the TH-cam video description and adding my TH-cam homepage
Thank you so much🤝🤝👍👍
No worries, give credit where credit is due, i say :) Thank You for the pinout!!!!
@ DIY Sim Racing : thank you for your tutorial, thank you so much!!!
@@user-spv96x3x7i.4kc Thanks for the support
Subscribe to my channel if you like it
Related DIY tutorials will be updated in the future
About noise modulation
You adjustable PN188
Is there a tutorial on the motion? That is awesome!
Amazing man !
This is the most virgin thing and i want it
I’m done having sex😭😂 I just bought a 2018 cry 450. Got a new truck and a new 4 wheeler. Got some land and a new travel trailer. Being freshly divorced is amazing😭😂😂😂
@@mrcontroversy222 perfect
Real nice. Love your work. Did you build the 6dof your self? You just need VR and you've got yourself a beast set up right there. Some links for some of your parts would be epic.
Cheers! Yeah i built it myself, There should be Links to both the wheel build and the 6dof build threads in the description. :)
I have VR but with all these peripherals i am out of usb ports and bandwidth haha. Waiting for my powered usb hub to arrive as they're all sold out locally.. damn covid! I also just put up a build video of my actuator if you're interested.
extremely interested man.. thaaaanks very much. I'm going from g27 to your dd stile wheel. And if I had the coin I would go 6dof motion too. One day
Well ! 👍
Such an upgrade going from a belt-drive wheel to a direct drive !! I just moved into an OSW Simucube. Totally love it. Instant improvement in lap times
Does the stm board send a pulse signal and direction signal?
Like could it be used with a stepper motor + driver instead?
How did you get the software part of your rig to work? All the telemetry translated into actuator motions. This is very impressive!
Hey mate, I use a program called FlyPT Mover.. there are others like Simtools as well. They grab the telemetry data and create a motion model based on your type of rig and then send the actuator movements to the Thanos controller, where those movements are then send to your individual actuators :)
I want to build a DIY FFB with a stepper motor instead of a servo because it's cheaper. Do you think it's possible to build it with a Nema 34 85kgf.cm, driver DM860A 7.2A and 80VDC power supply? Do you think I'll feel every step or it's going to be smooth setting with 40000 cpr?
Very goood👍👍
nice
I own the g27 and would like to upgrade to a direct drive but the ones on the market are too expensive and not worth it. Does thi solution improve in terms of strenght and details of the road and the car?
Well 2.4nm vs 25nm its a massive difference. Everything is improved. They aren't even comparable haha.
Hey mate, a guys is selling a old wangan 3dx arcade motor, I have a g27 do you think I could just take the power cables that go to the g27 motors and attach them to the arcade motor(as well as encoder) do you think this would work?
Basically just adapt all the logit tech gear to the much bigger dc motor
Im interested in this. Can you also link places where you bought all parts from?
hey mate, check out the Xsimulator link in description
Just saw your reply to another comment. I'll check out that link
monster servo motor...
she does alright... Bigger is better, right?!? haha
@@peacemakermotion3949 Can you explain me it feel like real? It's will lock strong? if reach the over 900 angle of steering wheel?
Now you just need VR!
there's a vr controller behind his seat straped to it
Can we used a BissC encoder with this configuration?
Not yet. Not with mmos. But somung soon is a new control board that will use it with VNM car simulator firmware and a Mige servo driver
Hi, I have wired it all up and set up the STM32 to run the MMOS firmware. I ran some tests and found that the encoder was being picked up, but there was no force feedback. I am not sure whether it is because I was using incorrect settings or because I had pin 6 of the DB25 connector open (not connected to GND). Any help/guidance would be more than greatly appreciated
Have you got your estop set up so that its a closed circuit when its released? I think I said normally open in the video somewhere.
@@peacemakermotion3949 thanks for such a fast reply as well!
@@peacemakermotion3949 It is moving now once plugged in, so i changed pn191 from 0 to 1 and it just moves in the opposite direction.
@@lou2737 no worries. hmmm.. somethings a miss somewhere.. I would start by triple checking your MMOS settings then your AASD driver settings and then your pinouts.. It's easy to mess one simple thing up along the way and it wont work properly.
@@peacemakermotion3949 hi again... It's working now however there is loads of high frequency noise coming from either the driver or the motor... Anyway to reduce this noise?
Hi! Is amazing!! How good is this OSW solution against IONI CUBE driver. Have any difference? What PSU do you use (voltage and power)?
Hey, never tried simucube. This uses AASD servo driver which is 240V main difference is encoder as it's a 2500PPR. Biss-C encoder not compatible with MMOS firmware
How did you setup to run on 110 power
Buenos días señor gran viendo la verdad k eres un magiver del siglo 21boy a intentar ASER uno jeje
Anyone knows what drift cat mod is this on the second part of the video?
Its the Nissan s14 zenkei on project togue track
@@peacemakermotion3949 thank you so much man ^^
Could you explain the assembly in more detail? we appreciate it. Thank you
Did you check out my built tutorial?
@@peacemakermotion3949 is it worth riding? gives failures? what is the final price of mounting it? greetings from Spain ✌️
@@chibiverin well my price was 450 usd.. then if you want the thanos DAC board at 100usd.. or you can use VNM firmware and use the discovery boards built in DAC. I don't have any issues.. you will want to be weary of EMI interference though so I would replace the motor power cable with shielded cable. So add 30 bucks.. you also want to try get a shielded db25 cable If possible. But yeah the price is without a wheel of course. You'll need to source one of them or build one
Also worth noting the AASD drive has a high pitch noise which does affect some people..
Your rig is way too sophisticated for you to be using a DIY solution or a G27
I didn’t expect this from someone who has a fantastic rig
The thing is my whole rig is DIY so a DIY wheel solution made sense. i feel bad for buying V3 clubsport pedals because i would usually DIY them too.. maybe in the near furture i will do that as well haha. This wheel project saved me money to afford the decent pedals though so thats good i guess :)
then buy him a better solution. if not, dont complain about s**t. have you made a whole DIY rig?
You must have the coolest wife in the world to let you have that in your house!
Wife hack #329 - Start Building Simulator before finding a wife. Can also be applied to Fast Cars and Man Caves.. 😂😂😂.
I would like to make one myself but Thanos is retired...
www.thanos-motion.com/
@@greysa69 Oh that's pricey!
Would you like to sell your old pedals
Nah man.. we all need a backup these days ;)
Peacemaker Motion Sim yeah man I was just messin. Cool vid though
@@TheThumbsUpChannel although... with the crack money covid prices things are selling for these days i could probably sell them for what the whole g920 set cost me hahaha.. hmmmm.... 😂
Peacemaker Motion Sim that is very true
@@TheThumbsUpChannel kind of makes this whole cheap direct drive setup even more relevant i guess haha
1 year later and you cannot find a small mige under $450
Works good it seems but the noises it makes I do not like lol
Noise has been eliminated with use of a DAC :)
@@peacemakermotion3949 oh nice
G'day mate..thank goodness i found ya vid. check out my last YT vids and you will see why I need your help and advice.
I fried mine just now.
on ya mate
is your wife happy about this build ?
Shes very impressed with it actually. Dislikes the amount of time I invest in it over her but you know.. just gotta try share the love around equally to keep the peace haha
bro wtf is this kind of a setup. big motion rig ,dd base ,high end gaming pc, but logitech pedals....
Haha. Its called prioritising your spending. Unfortunately i dont have wads of cash to throw around at any given time and the pedals worked fine for the time being. Actually the money i saved from doing this DD wheel over a simucube paid for my new pedals. I now run some Fanatec V3's and they're a great upgrade on the logitechs. I'll build some heusinkveld clones one of these days. Baby steps man lol
@@peacemakermotion3949 alright i understand. Waa just wondering 😅
@@BikesnB i was always embarrassed about that.. early days.. having logitech gear on the rig.. made me cringe everytime i edited a video haha
@@peacemakermotion3949 if you do heusinkveld clones, it would be awesome, cause heusinkveld is so dawn expensive
Before I die because of a electric shock or when my house burn down I buy a professional dd instead of making this
More then $450. I hate when you youtube people think tons of people have this shit laying around or a 3d printer.
still less then an off the shelf direct drive