A little hard to follow with the zooming, but this video finally got me set up. I’ve reflashed and reset and reconfigured my pi repeater at least 20 times, then to finally find this video and got it to work!!
ola Hristo thanks for answering my questions, your answer was very enlightening in general I use my router as repeater and I seek the best performance in this mode of operation, I have upgrade plans on a more robust router wr940n for openwrt firmware, I intend to configure it in relay mode and test its performance, if successful, I will inform ok tankyou Mr.
Thank you, how can I relay using a dual-band router in OpenWRY? I'd like to connect to the primary router using the 2.4ghz interface with subnet A, and share the internet on 5Ghz interface and different subnet to separate the local networks, and both have the internet. Thank you.
Add new lan and put the 5Ghz radio on him ! Set ip address and dhcp server. Finally snat the new lan with relayed bride ip address or wlan station ip address.
This was very helpful, and just what I was looking for! I'm using it with a Ubiquiti AirRouter... and OpenWrt Barrier Breaker 14.07 / LuCI Trunk (0.12+svn-r10530). Everything seems to work (I can connect via my one LAN port, or via the DHCP-assigned IP on the AirRouter (from my main router)... but I can't get DHCP on my LAN ports... Can you think of what might be wrong with my configuration if that's the case? I haven't tried connecting to the AirRouter via WiFi yet...
Hi Dave, I can not know if you properly configured the router, but you need to split the router's ethernet ports into 2 vlans and then put each, the first one to the local bridge for the local access and the second vlan to the second bridge /with relayd/ for the extended network .
thanks a lot Hristo you rock man!. i followed every step. but the only difference is that i have a 5ghz antenna too, so at the end i scaned and become client of that 5g too. i think i did ok. so i have a question just to make sure: you say at the end that you can plugg devices throuhg ethernet port 1 2 3 and conect to internet. ok. then you say that if you want to access router wirelessly you could with ip 172.16.222.212? is this right? and that conecting a device with ethernet in port 4 only will give us acceso to router and not to internet? is that so?
Hi Hristo, Thanks for sharing. I am running FriendlyElec NanoPi-R1S-H5 with OpenWrt R20.3.5 / LuCI Master (git-20.062.50551-a6189c5) and the kernel version is 4.14.111. The problem is that after the luci-proto-relay is installed, I cannot find the relayd protocol when I want to create the last bridg-relay interface. Could you help me with this since it bothers me for 3 days. Thanks.
Hi, first chеck they are installed relayd and luci-proto-relay packages ? If so, choose the protocol from the newly created bridge or interface to work with!
@@maoli3613 You must select it from the "protocol" drop-down menu , or create / modify the interface protocol with a text editor /etc/config/network file !
Hristo Popov I know. The problem is I cannot find the relay protocol from the drop down menu. May I get in touch with you via Telegram so I can show you the screen shot. My account is LeeDatou. Thanks in advance.
Hi. It works only if i put static addresses on my notebook. If not, I am not getting any ip and i don't know why... Main router is Mikrotik HAPlite, second (client) is TP-Link 1043 v2 with OpenWRT19
Thanks, this worked perfectly. but I want to configure it as a wireless repeater too. I went into the wireless tab after completing all the steps in the video , added a new access point, linked it to wwan but when I go about connecting a wireless device it gets stuck at "obtaining ip" , (DHCP configuration thing?). I don't know what I am talking about. Please help
Why did you install LEDE? Your router is newer and should be installed with OpenWRT 18.06.2 ! Try the update version by reading here - openwrt.org/toh/asus/rt-ac58u !
It is possible only firmware update like in this forum forums.hardwarezone.com.sg/internet-bandwidth-networking-clinic-4/asus-rt-n56u-secondary-router-wireless-bridge-possible-4480164.htmland make rt-ac58u repeater mode?
@@jbgrenouille2527 Ok, i understand now . Set first vlan on ethernet and add him ip address . You have two options for this first: config device option type '8021q' option ifname 'eth0' option vid '222' option name 'vlan222' config interface 'lan2' option type 'bridge' option ifname 'vlan222' option proto 'static' option ipaddr '192.168.2.1' option netmask '255.255.255.0' or second: config interface 'lan2' option type 'bridge' option ifname 'eth0.222' option proto 'static' option ipaddr '192.168.2.1' option netmask '255.255.255.0'
@@lucasburgueira Same problem to me, I simply saved and then restarted the router, it will appear (probably the restart should be done after installing the relayd packages).
От души, благодарю !
A little hard to follow with the zooming, but this video finally got me set up. I’ve reflashed and reset and reconfigured my pi repeater at least 20 times, then to finally find this video and got it to work!!
hi, I can't seem to find the "physical setting".. and in the device setting what do I need to do?
Can you record that without zooming? It's very hard to follow your steps :(
maybe soon :)
@@hristopopov4724 Thanks!
ola Hristo thanks for answering my questions, your answer was very enlightening in general I use my router as repeater and I seek the best performance in this mode of operation, I have upgrade plans on a more robust router wr940n for openwrt firmware, I intend to configure it in relay mode and test its performance, if successful, I will inform ok tankyou Mr.
I'm not generally a fan of this setup, but sometimes that's the solution!
Thank you, how can I relay using a dual-band router in OpenWRY? I'd like to connect to the primary router using the 2.4ghz interface with subnet A, and share the internet on 5Ghz interface and different subnet to separate the local networks, and both have the internet. Thank you.
Add new lan and put the 5Ghz radio on him ! Set ip address and dhcp server. Finally snat the new lan with relayed bride ip address or wlan station ip address.
This was very helpful, and just what I was looking for! I'm using it with a Ubiquiti AirRouter... and OpenWrt Barrier Breaker 14.07 / LuCI Trunk (0.12+svn-r10530). Everything seems to work (I can connect via my one LAN port, or via the DHCP-assigned IP on the AirRouter (from my main router)... but I can't get DHCP on my LAN ports... Can you think of what might be wrong with my configuration if that's the case? I haven't tried connecting to the AirRouter via WiFi yet...
Hi Dave, I can not know if you properly configured the router, but you need to split the router's ethernet ports into 2 vlans and then put each, the first one to the local bridge for the local access and the second vlan to the second bridge /with relayd/ for the extended network .
Thanks for your response Hristo - yes, I did that, or at least I think I did! I'm wondering if I've got a hardware/relayd compatibility issue perhaps?
@@DaveLaneNZ If you want, try upgrating the firmware with the latest stable release - openwrt.org/toh/ubiquiti/airrouter
Where can I find to download OpenWrt Barrier Breaker 14.07 / LuCI Trunk (0.12 + svn-r10530) please-.
I cannot get the packages to update no matter what I try :/
thanks a lot Hristo you rock man!. i followed every step. but the only difference is that i have a 5ghz antenna too, so at the end i scaned and become client of that 5g too. i think i did ok.
so i have a question just to make sure: you say at the end that you can plugg devices throuhg ethernet port 1 2 3 and conect to internet. ok.
then you say that if you want to access router wirelessly you could with ip 172.16.222.212? is this right?
and that conecting a device with ethernet in port 4 only will give us acceso to router and not to internet?
is that so?
Yes .... wirelessly connected to the main AP .More than one wireless connection in relayed bridge can make a network loop !?
The zooming makes me crazy.
Hi Hristo, Thanks for sharing. I am running FriendlyElec NanoPi-R1S-H5 with OpenWrt R20.3.5 / LuCI Master (git-20.062.50551-a6189c5) and the kernel version is 4.14.111. The problem is that after the luci-proto-relay is installed, I cannot find the relayd protocol when I want to create the last bridg-relay interface. Could you help me with this since it bothers me for 3 days. Thanks.
Hi, first chеck they are installed relayd and luci-proto-relay packages ? If so, choose the protocol from the newly created bridge or interface to work with!
Hristo Popov yes，they are all installed and enabled from ssh. Still cannot choose relay protocol. I can send you the screenshot.
@@maoli3613 You must select it from the "protocol" drop-down menu , or create / modify the interface protocol with a text editor /etc/config/network file !
Hristo Popov I know. The problem is I cannot find the relay protocol from the drop down menu. May I get in touch with you via Telegram so I can show you the screen shot. My account is LeeDatou. Thanks in advance.
@@maoli3613 Use any of the photo sharing sites like postimages.org and then post the direct link here
i.postimg.cc/C180Zg8H/owrt-Relayd.png
Hi. It works only if i put static addresses on my notebook. If not, I am not getting any ip and i don't know why... Main router is Mikrotik HAPlite, second (client) is TP-Link 1043 v2 with OpenWRT19
It was because of Mikrotik device... with other TP-Link as main router, everything is working!
Have my like Sir, the zoom thing is not relevant when the setup worked perfectly
hello, good vide. Please can tell me how to configure kmod-trelay for wifi-to-wifi bridge mode? thanks
Thanks, this worked perfectly. but I want to configure it as a wireless repeater too. I went into the wireless tab after completing all the steps in the video , added a new access point, linked it to wwan but when I go about connecting a wireless device it gets stuck at "obtaining ip" , (DHCP configuration thing?). I don't know what I am talking about. Please help
how can i make rt-ac58u repeater mode:
i donwloaded and installed LEDE. But i dont have wireless tab...
Why did you install LEDE? Your router is newer and should be installed with OpenWRT 18.06.2 !
Try the update version by reading here - openwrt.org/toh/asus/rt-ac58u !
It is possible only firmware update like in this forum forums.hardwarezone.com.sg/internet-bandwidth-networking-clinic-4/asus-rt-n56u-secondary-router-wireless-bridge-possible-4480164.htmland make rt-ac58u repeater mode?
Openwrt is complex
im gonna call it "full of features"
Don't use GUI, my hand hurt just from watching.
Good video !!!!
any idea how can i do it with CPE SXT lite 5 mikrotik - openwrt ??
thanks advance
just scan and connect the sxt to the openwrt AP After that put the wlan interface in the local bridge -
try it, I hope it works
Hristo Popov i have the sxt lite5 with openwrt OS
@@jbgrenouille2527 Ok, i understand now . Set first vlan on ethernet and add him ip address . You have two options for this
first:
config device
option type '8021q'
option ifname 'eth0'
option vid '222'
option name 'vlan222'
config interface 'lan2'
option type 'bridge'
option ifname 'vlan222'
option proto 'static'
option ipaddr '192.168.2.1'
option netmask '255.255.255.0'
or second:
config interface 'lan2'
option type 'bridge'
option ifname 'eth0.222'
option proto 'static'
option ipaddr '192.168.2.1'
option netmask '255.255.255.0'
Hristo Popov he was config but with nat, wwan and lan two interface.
Hristo my idea is that the public ip reaches my router's wan, I want to avoid the “double nat”
I installed relayd but it wont appear in "Protocol" tab... Don't know what to do now...
luci app to !
@@hristopopov4724 what? didn't understand that D:
@@lucasburgueira install luci-proto-relay too :)
@@hristopopov4724 I did, same thing in the end :/
@@lucasburgueira Same problem to me, I simply saved and then restarted the router, it will appear (probably the restart should be done after installing the relayd packages).
sucks too zoomed
openWRT is pain in the ass.... spent hours to configure this shit... without success..