You gotta see the video I'm dropping in the morning. Extensive study on engraving clear acrylic. LOTS of information. And a surprising engrave after hours of tests. Thanks for subscribing and stay tuned.
I've made a few jigs. But when engraving with this technique on clear acrylic a jig is not helpful. Each piece needs to be in a different location to be on a virgin primered surface. Without the fresh surface the engraving isn't as successful. Thanks for watching.
Think multiple acrylic inserts. The seasons....Holidays...children....grandchildren...pets....probaby more. Sell them as extra add on. I am going to try that...I am not interested in selling but will do it for family and friends.
I have only had my xtool D1 for a month so I am learning also. you can not give settings you use because they probably will not work for other. I am following 10 youtube laser channels and they all say the same thing about settings. I like your presentations. I find them informative and interesting. Keep up the good work
Great Video I will be trying that. And correct there many conditions for settings, but what is your set condition because that gives a base line, especially with primer on steel. Can you share? a base line to start with could help. I like the technique because trying with Tempura paint is is very un even. Thanks again, great video
Thank you for the video. Does it matter what the base metal that the primer is applied to? After the primed metal is used several times can you just strip the primer off and recoat?
I use the metal that came with my honeycomb. When the steel no longer has a clean unmarked surface to use for engraving, I sand it down and put a fresh layer on. I use the Filler and Sandable Primer. This fills the voids from the previous engravings and leaves a smooth surface to start fresh with. Here's a link to the primer I use. amzn.to/3IeQIx4
enjoying your channel, looking to buy an xtool d1, mostly hoping to cut veneer with it. Watching your channel in the hope to learn with you, big thanks
not sure if i missed it, but how are you planning to customize the shapes of the plexi? The examples on etsy you showed were in the shape of a football or starwars figure. The diode can't cut out the shape.
Thanks for watching and your question. You didn't miss it. I, too, am learning. The pictures on Etsy with the custom shapes were only for an idea what these are selling for. You are correct about not cutting these with the diode. To get super nice shapes like those, I'm going to use a CNC router to get clean, precise cuts. And if you don't polish the cut edge, it serves as a line in your design when lit. Thanks again for watching. Please subscribe.
Did you use the Cold Galvanizing paint on the steel? If not which one did you use? Also for a point of reference what were your settings on the 10watt that actually worked?
I have not used the Cold Galvanizing on my stainless, yet. It's the only reason I haven't returned it yet. I may need it when I go to engrave/mark on stainless. But the most impressive marking on stainless results I've see are from using Cermark. But that stuff is crazy expensive for a simple hobbyist. As for the settings on my 10watt, if you're asking about the settings I used on the acrylic, I'm making a new video today for tests on clear acrylic. It will be only dealing with the settings and technique on clear acrylic. Stay tuned and please subscribe.
@@HoboWithWood I have subscribed, I also have cermark already, but if you touch it it leaves a mark. So I was just looking at the gray color you painted the steel and that is why I asked.
@@rickhoguerealtor the steel is covered in Rustoleum Filler Primer. It works great. After my work surface is filled with burns, I sand it lightly and spray it again. Good as new.
Some are more aggressive than others when it comes to the licensing infringement. Disney is one of the worst. I've heard tale of them having folks that visit large craft shows and shut down people selling items with Disney characters. if you're making it for your own personal use, you'll probably be okay. But be weary of items that may require a license to produce and sell. I am from NC and have family and friends that have graduated from UNC and NC State. These items I give as gifts for birthdays and holidays.
Ck out this video about the settings for this project and others engraving clear acrylic. There was a lot more to it than just the settings. This video goes in detail how I found my settings and what they were. th-cam.com/video/y5DhgHH7YNE/w-d-xo.html Thanks for watching.
Thanks for watching. The name Hobo came from the fact I am a full-time RV'er. Until fuel hit $5.50 a gal. there is no telling where you'd find me. But currently you'll find me hiding in Gastonia.
My top secret formulation of two of the most prominent elements on the periodic table combined to create the perfect cleaning solution in most cases. I'll share it with you, but it has to stay between us. Okay? Here the formula H20. I have a really neat device that allows me to simply turn on the tap and it comes out in abundance. It works well on its on. But a drop a dish soap doesn't hurt. Remember this must stay between us.
Thank you for the kind words. I purchase these on Amazon. They sell really well. Here is the link to ones I use. Thanks for watching. hobowithwood.com/LED-Night-Lights
Jaros thanks for watching. You are new to my channel. I do not talk about settings, except that it absolutely necessary for you to run tests on your laser to determine the best settings for your laser and any given material. My settings will not work for you. My xTool is defective at best. It hasn't been right since the day I opened the box. The only way I'm able to produce any quality work is I test every material to determine what my laser is capable of. I've done more videos engraving acrylic in which I did talk about my settings and showed the tests I did to arrive at the best settings. I suggest watching this, it may answer some questions for you. th-cam.com/video/y5DhgHH7YNE/w-d-xo.html Thanks for watching.
You sure like to hear yourself talk ): and again you do not even give a close hint to the settings, we all understand there are differences in setting for different materials. but there are many other TH-cam videos that give setting to help get things rolling. watch some of the videos from Viper Designed/ glass on the fly. learn how to do them better, you have good info but not having the details is not that helpful. The guys you mentioned do much better and they will give details without fear.
My videos are posted for entertainment purposes only. The channel disclaimer tells you just that. At the time of this recording, I had only been working with the laser for less than 3 weeks. I knew very little compared to what I've learned up to now. But I still don't post settings for my laser. There is no way to guarantee my settings will work for anyone else. The reason I mentioned the guys I do, their channel is more of a "How To." I am an entertainer. If you didn't find it entertaining and would like a refund, send me a receipt for your purchase and I will be happy to send you a refund. While I'm sure you won't find this reply entertaining either, I'm also sure, more will find it entertaining than not. I'm sorry I disappointed you. But I'm used to disappointing others. Ask my ex-wife.
@@HoboWithWood Ol' Big Irish must not have had his hearing aids turned up because you said in your video that that this was NOT a how to tutorial. Caint please everyone. I enjoyed this video, and I am a subscriber to your channel. Keep up the good work. I'm looking forward to receiving my D1 20w soon, and will be watching for more videos.
![[Full Episode] Hell's Kitchen Thailand EP.12 | 28 เม.ย. 67](http://i.ytimg.com/vi/xCjbu5t25Pw/mqdefault.jpg)
Thanks for the video! Nice engrave on clear acrylic.
You gotta see the video I'm dropping in the morning. Extensive study on engraving clear acrylic. LOTS of information. And a surprising engrave after hours of tests. Thanks for subscribing and stay tuned.
Good Job, I really like your videos
Very cool to see how you make this nice things. We enjoy it in Holland
Thank you very much! I'm just getting started, so stayed tuned. Thank you for watching.
You can create a jig square with the D1 for the different products you make. That way you can speed up the projects and increase accuracy. Nice work!
I've made a few jigs. But when engraving with this technique on clear acrylic a jig is not helpful. Each piece needs to be in a different location to be on a virgin primered surface. Without the fresh surface the engraving isn't as successful. Thanks for watching.
nice
Thanks
Think multiple acrylic inserts. The seasons....Holidays...children....grandchildren...pets....probaby more. Sell them as extra add on. I am going to try that...I am not interested in selling but will do it for family and friends.
I have only had my xtool D1 for a month so I am learning also. you can not give settings you use because they probably will not work for other. I am following 10 youtube laser channels and they all say the same thing about settings. I like your presentations. I find them informative and interesting. Keep up the good work
Thanks Jon. Thanks for watching. And thanks for the kind words.
Great Video I will be trying that. And correct there many conditions for settings, but what is your set condition because that gives a base line, especially with primer on steel. Can you share? a base line to start with could help. I like the technique because trying with Tempura paint is is very un even. Thanks again, great video
I used various settings. Settings I used most often were 10W, 1998 mm/m, or 33.3 mm/s, 75% power & 317.5 LPI. Single pass.
Thank you for the video. Does it matter what the base metal that the primer is applied to? After the primed metal is used several times can you just strip the primer off and recoat?
I use the metal that came with my honeycomb. When the steel no longer has a clean unmarked surface to use for engraving, I sand it down and put a fresh layer on. I use the Filler and Sandable Primer. This fills the voids from the previous engravings and leaves a smooth surface to start fresh with. Here's a link to the primer I use. amzn.to/3IeQIx4
enjoying your channel, looking to buy an xtool d1, mostly hoping to cut veneer with it. Watching your channel in the hope to learn with you, big thanks
Fumbling my way through. Trying to learn something everyday and make so money along they way. Thanks for watching.
not sure if i missed it, but how are you planning to customize the shapes of the plexi? The examples on etsy you showed were in the shape of a football or starwars figure. The diode can't cut out the shape.
Thanks for watching and your question. You didn't miss it. I, too, am learning. The pictures on Etsy with the custom shapes were only for an idea what these are selling for. You are correct about not cutting these with the diode. To get super nice shapes like those, I'm going to use a CNC router to get clean, precise cuts. And if you don't polish the cut edge, it serves as a line in your design when lit. Thanks again for watching. Please subscribe.
@@HoboWithWood Sounds good Steve. Please post a video when you create these on the CNC, I'd love to see process.
What kind of primer ?
Did you use the Cold Galvanizing paint on the steel? If not which one did you use? Also for a point of reference what were your settings on the 10watt that actually worked?
I have not used the Cold Galvanizing on my stainless, yet. It's the only reason I haven't returned it yet. I may need it when I go to engrave/mark on stainless. But the most impressive marking on stainless results I've see are from using Cermark. But that stuff is crazy expensive for a simple hobbyist. As for the settings on my 10watt, if you're asking about the settings I used on the acrylic, I'm making a new video today for tests on clear acrylic. It will be only dealing with the settings and technique on clear acrylic. Stay tuned and please subscribe.
@@HoboWithWood I have subscribed, I also have cermark already, but if you touch it it leaves a mark. So I was just looking at the gray color you painted the steel and that is why I asked.
@@rickhoguerealtor the steel is covered in Rustoleum Filler Primer. It works great. After my work surface is filled with burns, I sand it lightly and spray it again. Good as new.
Can I see a pic of the primer can please?
Can you reuse the metal over again? Can you repaint it or do you need to replace? Thanks
I sand it smooth, recoat and reuse. I use a sandable filling primer.
Hey! Thanks for the video! I am brand new to this. I know you referenced the NFL and how you would avoid that. But, is it ok to do NCAA etc…?
Some are more aggressive than others when it comes to the licensing infringement. Disney is one of the worst. I've heard tale of them having folks that visit large craft shows and shut down people selling items with Disney characters. if you're making it for your own personal use, you'll probably be okay. But be weary of items that may require a license to produce and sell. I am from NC and have family and friends that have graduated from UNC and NC State. These items I give as gifts for birthdays and holidays.
Ok. I’ve been trying to figure out how to navigate that. Thanks!
What was the settings you used for this project?
Ck out this video about the settings for this project and others engraving clear acrylic. There was a lot more to it than just the settings. This video goes in detail how I found my settings and what they were.
th-cam.com/video/y5DhgHH7YNE/w-d-xo.html
Thanks for watching.
Thanks for the info.... What part of NC? I am SE of Raleigh.
Thanks for watching. The name Hobo came from the fact I am a full-time RV'er. Until fuel hit $5.50 a gal. there is no telling where you'd find me. But currently you'll find me hiding in Gastonia.
How are you cleaning the acrylic after the burn?
My top secret formulation of two of the most prominent elements on the periodic table combined to create the perfect cleaning solution in most cases. I'll share it with you, but it has to stay between us. Okay? Here the formula H20. I have a really neat device that allows me to simply turn on the tap and it comes out in abundance. It works well on its on. But a drop a dish soap doesn't hurt. Remember this must stay between us.
Hi friend, what a great job!
Did you buy the Acrylic piece at a local store or on the internet? A hug from Brazil!
Thank you for the kind words. I purchase these on Amazon. They sell really well. Here is the link to ones I use. Thanks for watching. hobowithwood.com/LED-Night-Lights
It is I who thank you!
Some of your best help is the "how not to" youtubes.
what are the settings you used for that ?
Jaros thanks for watching. You are new to my channel. I do not talk about settings, except that it absolutely necessary for you to run tests on your laser to determine the best settings for your laser and any given material. My settings will not work for you. My xTool is defective at best. It hasn't been right since the day I opened the box. The only way I'm able to produce any quality work is I test every material to determine what my laser is capable of. I've done more videos engraving acrylic in which I did talk about my settings and showed the tests I did to arrive at the best settings. I suggest watching this, it may answer some questions for you.
th-cam.com/video/y5DhgHH7YNE/w-d-xo.html
Thanks for watching.
Could you please let me know what was speed and power
Here is a link to the latest acrylic engraving I did. It shows the powers and success.
th-cam.com/video/y5DhgHH7YNE/w-d-xo.html
Hola.señor que material coloca debajo del acrilico ese material.gris
It is the steel plate that came with my honeycomb. It has been painted with automotive primer. It can be sanded and sprayed over and over.
Can you use an ipad instead of a computer
I don't know anything about Apple products or their capabilities. Sorry.
@@HoboWithWood thanks for the response!
Rub the acrylic with your hands WILL SCRATCH the acrylic
I don't have a problem with the acrylic I use scratching.
I only found a 54mil youtuber.
Isn't selling Tar Heels and Wolfpack items without their permission a Trademark Infringement Violation? Pretty Sure it Is!!
You sure like to hear yourself talk ): and again you do not even give a close hint to the settings, we all understand there are differences in setting for different materials. but there are many other TH-cam videos that give setting to help get things rolling. watch some of the videos from Viper Designed/ glass on the fly. learn how to do them better, you have good info but not having the details is not that helpful. The guys you mentioned do much better and they will give details without fear.
My videos are posted for entertainment purposes only. The channel disclaimer tells you just that. At the time of this recording, I had only been working with the laser for less than 3 weeks. I knew very little compared to what I've learned up to now. But I still don't post settings for my laser. There is no way to guarantee my settings will work for anyone else. The reason I mentioned the guys I do, their channel is more of a "How To." I am an entertainer. If you didn't find it entertaining and would like a refund, send me a receipt for your purchase and I will be happy to send you a refund. While I'm sure you won't find this reply entertaining either, I'm also sure, more will find it entertaining than not. I'm sorry I disappointed you. But I'm used to disappointing others. Ask my ex-wife.
@@HoboWithWood Ol' Big Irish must not have had his hearing aids turned up because you said in your video that that this was NOT a how to tutorial. Caint please everyone. I enjoyed this video, and I am a subscriber to your channel. Keep up the good work. I'm looking forward to receiving my D1 20w soon, and will be watching for more videos.