วีดีโอ

Thanks Frank!!

im looking forward to buy a single 10" idq d2 v2 for a hatchback car, im not looking for extreme spl, is it worth it still? i cant find the spec sheet anywhere

Perfect fix and to the point! Thank you

I agree it's related to power, but I'm not sure it is with the button, though. I too have the same problem sometimes. When it 'clicks', I turn off the lights so the battery has more power available for either the starter relay, or the starter itself. Since the starter motor was replaced not so long ago, I think it's the starter relay all along.

I did that same thing and it failed horribly. It only crimped down one of the two wings after making that little opening for the chisel to rest in.

fucking useless video, never showed us how it was done.

Frank I'll give you the secret, and everyone else. Position the circlip with the open end at the 12 o'clock position - once the splines mate up, it should slip right in by hand or maybe a gentle tap. Same thing coming apart - if it's giving you grief releasing just turn an 1/8 of a turn at a time and pull - once that clip is in the 12 o'clock open end up it will release!

Id solder it too

Thank you for the tip,I have a 96 as well,I'll do that to try.😊

Thanks, but you can get the replacement set for front and rear for $10. I would def replace that 20 year old plastic

That was awesome

Super helpful! Could you tell me what type of wire you used? Going to try this fix on mine. Thanks!

Short and to the point. Thank you.

I’m a little confused, all you did was remove the factory wire and replace it with a new wire?

It didn't work on an VW mk6 Jetta

How do I get the lever out from the cover? Do i just pull it out?

Do you have any info on that rear swing arm and wheel setup your running that looks great

Thanks for the video. I had kinda the same issue on another bike, with a clutch sensor underneath clutch level. Grease got on contacts and didn't let bike start. Cleaned contacts and started up.

Just did this to my ZX7 a few days ago. It had an intermittent "no crank" Seemed like every other press of the button did nothing. Thanks for sending me in the right direction with the repair! It actually comes apart and goes back together quite easily. Anyway, Thanks Again!

Great info

How do I get the latch out? The cover seems straight forward but I can't figure out the latch.

This is so stoopid.

Thank u so much for this info ℹ️ video

Thank you.. Could you let me know how to do the single swingarm? Also if you ever would like to sell your ZX7 let us know. Thank u

Thanks a lot ! I have that problem and I will be fixing it thanks to you !

An absolute hero, would have never got it. Cheers

Thx man...

That seems to get an effective crimp, but I'd probably want to run a high amperage voltage drop test on it (and also check for heating). MIght work good when your options are limited. I probably have a couple thousand dollars invested in crimping tools, but my favorite is one of those Hammer Lug Crimpers you can get for about $14. If you hit it hard enough, you get a great cold weld. It's epecically useful because every manufacturer of cable lug seems to use a different wall thickness, and not every 4 AWG wire is actually 4 AWG.

hi boss. but in that moment not have pressure. the check valvule works when the pressure to be current?.

Oh wow oh my God I just stumbled across this video and I've already sunk only 50 bucks on a new starter but hopefully it won't be any more than that cuz I haven't actually tested the starter but now that I got the same exact click on my 98 ZX6R it was intermittently working I cannot wait to go home and try this as that starter sounded as healthy and great as anything and I couldn't understand why I would just feel like that without slowly getting worse so I'm going to go home and tap that box and if I do and it starts I owe you a big one my friend I'll keep you in touch hopefully this works cross your fingers

legit just got a e36 sedan and was having issues with the tail lights kept stop working, deff going to be doing this fix on mine!

the heck are you doing in this video

What I wanna know is does that hole from the channel is going to affect the transmission because after all my research 90 percent don't have that extra hole

So where did you re ground the bike negative wire to if you removed it from the engine ground location ?

Hey Frank this Ty I'm now having this issue except it makes NO clicking sound at all. I have the start kill switch apart I cleaned the 2 prong connector pins that the 2 wires go attached to. The spring looks okay but will remove screw to inspect the contact points you mentioned here.

Bro if this fixes my bike tomorrow I’ll pass that like

might steal this idea and use it i’ve been trynna figure how i’m do mine

Thanks man that solve my problem :)

Nice one Frank, Greetings from Down Under. I had same trouble with a 2000 model ZX12R. Spent heaps trying to sort out why no go. Even sprayed contact cleaner in that switch, but eventually had a closer look and spotted a bit of corrosion on the locating screws inside starter button and thought this looks promising for rusted contacts, sure enough, that's what it was all along. Cheers.

around what miles do they fail usually?

Smart fix !

Good idea! I gotta do mine this weekend. I'm gonna do this and use ferrules at the other end.

I got one who wants it😊

FCP Euro offers sockets with a hex on top that can be turned with either an open end or box wrench. These are like “spark plug” style sockets but are available sizes commonly used for strut nuts: 22mm, 18mm etc. Price $9.99 ea. They work perfectly with t-handle torx wrenches for tightening struts.

I need help brother 😪

Life saver! I was working on a pathfinder and no other method worked but this one. A couple of taps got it right in! I'll never forget this trick after the fight I've had with this car lol

Mine is stuck open and I’ve already replaced it and I was wondering what if I put jb weld over that small circle would that help it close ???!

Nice video! I just bought a 2000 ZX7R and have been having starting issues similar to yours. Easiest way I could start it which brand new battery was to put a charger on the battery. Today I cleaned all terminals and checked the relay, nothing changed …. I just held down on start button and tapped the junction box and instant start up so I’m thinking I have the same issue you had! Nice I’m going to clean those contacts on the starter button now and I’m really hoping it fixes my issue also!

mannnn thank you! mine has been not working for at least 3 months and i was even thinking about swapping them to a module... this is way easier.

Definitely helped. Double like