I personally work at a tire shop where i live and i will be the first to say that yes we do takecare of all wheels and tires especailly if there new. However it is possible for something maybe to be in the wrong position and put a nice scratch across your brand new Akrons. I would strongly recommend letting them do the mounting and balancing for you cause in the end if they damage they will replace. Seams like a win in my books.
Tell that to the mechanics at my Toyota dealership who scratched the rims of my brand new truck during its first service. They would only pay for half of the replacement rim. And I had to wait 5 months for it! Not doing business with them again.
My worst one: not spending a little more cash and getting A/T tires on my first truck’s wheel setup. Went with all seasons and regretted it (got A/Ts after they wore out).
I made the load index mistake so when I needed to get the tires turned around on the wheels because somebody mounted the wrong side wall out (damn it, Carl) the local tire shop wouldn't service them on my truck. I had to take my floor jack and jack stands with me and take the shoes off my truck in the parking lot.
My fuel contras (24x14) are arriving in 7 days, I’m wrapping them in a set of 35x13.50 r24 venoms a/t for a little bit of a stretched look on my Jeep. I hope it goes well
My biggest mistake was slapping 2021 20x10 wheels w/295/45/zr20s on my 2016 durango R/T which cause them to kung fu my stock suspension control arms until I figured it out after a couple drives. I went down to some 275/45/r20 grabbers which don't guard the 10" wheel from potential curb rash the same but they fit the under the front arm since I wasn't sure about 285/50/r20 without a lift kit. I'm just studying suspensions & don't see much feedback about that size without a lift.
Haven't made a mistake yet, hoping not to due to here soon gonna be buying my first set of wheels tires and my suspension from Custom Offsets. Watched every video posted just to make sure I can fit what I want and will run the way I'm hoping.
@@tippy8358 nah that’s how you get a deal. i got bfg ko2s with almost full tread for half price. i also bought some venom power hunter RT for 300 and sold for 900 next day because they were brand new. My friend owns a truck shop so i bought new fuels through him for a deal then slapped on some marketplace tires
@@tippy8358 u can laugh all u want i found some fuels on facebook that were new for 400 dollars with new tires all mounted so u can say whatever but ill stick with saving 4k on wheels
I just bought the Venom Power Terra Hunter XT 33x12.50r20 load rating 119, they drive really well, I notice that on the tire cold it say 80 PSI, my TPM in the Silverado indicate 40 psi, I just got them installed, so my question is at what PSI you keep yours cold?
Bought a set of wheels and tires one time for a vehicle didn't take into consideration the offset. So they mounted closer to the suspension than would have liked lol. Lesson learned
Im putting 2.50 leveling front, 2inch rear leveling kit on 2022 z71, it has 20x9 factory wheels. Will 33-12.50-20 fit and what off set do i need for poke to be 1 inch or less outside of fender?
@@robertpawelek not that bad, I had recently replace tires so I just bought the wheels, finding a place to swap the tires on the new wheels was a bit of a challenge, and couldn’t find a place to install the leveling kit. One guy quoted me 850.00 for swapping wheels and installing the leveling kit. I ended up installing the leveling kit myself and between tires/TPMS swap + alignment was around 270.00
@@VortexVibe634 Nice! Hope you like the new look. I installed my own leveling kit as well, couldn't stomach the thought of the cost at the shops around town. Extra cash to put towards my new w/t setup now 😎. Hope to make a decision soon...
My biggest mistake was letting my local garage put my tires on my new wheels, did great putting them on, not so much taking them off, scratched to hell in the first 6 months ive had them, im going to be touching up the paint on them myself
i have a leveled 2016 ram 1500 4x4 with factory 20x9 wrapped on 35x12.50x20 and i want to purchase some wheels and want to go with some 20x12s -44 would it actually rub more cause i had to trim a little ?? thanks
Not at this time, but we got venom power's! www.customwheeloffset.com/store/tires?sort=instock&diameter_from=24&width_from=33&ratio_from=14.5&saleToggle=0&qdToggle=0
Biggest mistake was not knowing the correlation between load index and load range. My truck calls for Load Range D but does not specify load index. So I got some 35x12.50R22 117 Load index Load Range E, thinking they would be fine. Well, they would be, if I wanted to run them at 60PSI. But the factory tire pressure is 42PSI. So for this size, I need a 127 Load Range F. Why F? Because all that the letter indicates is the maximum acceptable pressure. For example, the 121 Load Index Load Range E has about the same load capacity at 42PSI as a 127 Load Range F. This is because the load index is calculated at the MAX PSI. For LR-E it is 65PSI for tires like these, and LR-F is 80PSI for tires like these. SO when you do the calculation, a 121 Load Index with Load Range D has MORE load carrying capability at the same PSI than a 121 Load Index with Load Range E. This is because the 121 load rating is now measured at 65 PSI rather than 50PSI. The only benefit from a higher load range is that you get to run the tire at higher PSI and because of that, you end up getting more load carrying capability. but ONLY NEAR max PSI. So now i have to dismount and remount new tires and rebalance that meet the load carrying spec for safety.
Biggest mistake was thinking I knew what I was buying when I didn’t because rn I have 20x10s but they are going to be my winter wheels and I already have my 24x14s ready for summer
Welp… drove an hour after convincing the guy to sell me wheels and tires he was gonna sell to someone else I paid extra thinking they were pro mags they were actually black painted trailer wheels and tires. I was pretty bummed now I’m stuck with them(:
Biggest mistake I made...not getting enough double stuffed OreoS! On a side note...looking for a nice set of wheels and tires for my F350 4x4 C C. L.B. I will know them when I see them
This whole trying to find out what tires real diameter is confusing. Then you go to gallery and you have guys running the exact same setups one says minor plastic trimming other one says major metal trimming.
It'll all depends on the lift,wheel offset,tire height. I had the shop mount 22s on a 2007 Chevy Silverado and had to do mayor metal trimming they look awesome though. The exact tire 285/55/22 -44 offset nitto Terra grappler,6 inch RC lift .
@@tonysilveira30 honestly ,it might be that some of the owners don't really have a clue of what had to be done to fit that set up and the ones that actually tells you what was done those might be the ones that did work on it.
Going to a non reputable shop to buy wheels and a lift I had a 3 inch lift and 20x8s after I paid for 20x12s and they wouldn’t change them or give me my money back 😂
talk to your social meadia or even better someone on the streets based on thier experience to make a decision on a lot money . custom offset has failed to mention that 20x12 will work for my application only after 20x10 has been shipped and installed now i’m having to save to get 20x12”s to fit my liking and application to begin with lessons learned knowledge is power and can possible save you a lot of money dont listen to sales as they want your money and be out
Bruh, I'm in that same situation rn lol. Got 35x12.50 22x12s over 24x14 last year cus I felt 24s were too big. Huge regret, now I'm in the process of buying some 24x14s wrapped on versatyre mt 36x14.50.
Not really true. Large wheels don't screw up your suspension, but it can accelerate wear on already failing components like ball joints or wheel bearings. -Fuller
Trusting the CO gallery.. yall don't verify shit. YOU CANNOT fit a 22x12 and 37s on a 19+ Ram HD with a 4" lift with NO trimming and No rubbing . It's not possible
I can't remember the last time I got taxes back. I am one of the few suckers that actually has to pay income tax. Pisses me off. All these people saying I need to pay more when they pay none. Sorry man just drives me nuts- BTW if you are getting money back instead of breaking even you are doing it wrong. Only mugs give the govt their money to hold on to- Everytime I see someone bragging about getting a big tax refund every year I just want to tell them how stupid they are for doing that and I lose respect for them
Couldn't help but notice after he keeps bringing his tatted arm across his body to show it off. Notice how every movement the tatted arm moves across the body to show it off and the other arm does not. Lol the little things 🤣
What’s the biggest mistake you've ever made buying wheels + tires? - bit.ly/3kuTdOM
I personally work at a tire shop where i live and i will be the first to say that yes we do takecare of all wheels and tires especailly if there new. However it is possible for something maybe to be in the wrong position and put a nice scratch across your brand new Akrons. I would strongly recommend letting them do the mounting and balancing for you cause in the end if they damage they will replace. Seams like a win in my books.
Tell that to the mechanics at my Toyota dealership who scratched the rims of my brand new truck during its first service. They would only pay for half of the replacement rim. And I had to wait 5 months for it! Not doing business with them again.
Hats off to the folks who mount and balance these beautiful wheels. I used to be a tire tech and I'd be too afraid I'd scratch them 😅
They hammer em out like nothin! 😎💪
My worst one: not spending a little more cash and getting A/T tires on my first truck’s wheel setup. Went with all seasons and regretted it (got A/Ts after they wore out).
I made the load index mistake so when I needed to get the tires turned around on the wheels because somebody mounted the wrong side wall out (damn it, Carl) the local tire shop wouldn't service them on my truck. I had to take my floor jack and jack stands with me and take the shoes off my truck in the parking lot.
My fuel contras (24x14) are arriving in 7 days, I’m wrapping them in a set of 35x13.50 r24 venoms a/t for a little bit of a stretched look on my Jeep. I hope it goes well
🔥🔥🔥
If I buy tires and wheels and have you Mount them. What do I do about my Factory TPMS?
Biggest mistake- not checking the lug dimensions first and got something that didn’t fit so had to get adapters
My biggest mistake was slapping 2021 20x10 wheels w/295/45/zr20s on my 2016 durango R/T which cause them to kung fu my stock suspension control arms until I figured it out after a couple drives. I went down to some 275/45/r20 grabbers which don't guard the 10" wheel from potential curb rash the same but they fit the under the front arm since I wasn't sure about 285/50/r20 without a lift kit. I'm just studying suspensions & don't see much feedback about that size without a lift.
Not too sure anyones lifted the new Durangos haha
Haven't made a mistake yet, hoping not to due to here soon gonna be buying my first set of wheels tires and my suspension from Custom Offsets. Watched every video posted just to make sure I can fit what I want and will run the way I'm hoping.
pretty dang expensive to buy from them, i would go to facebook marketplace
@@willpuckett8217 Facebook marketplace 😭😂 you poor bastard
@@tippy8358 nah that’s how you get a deal. i got bfg ko2s with almost full tread for half price. i also bought some venom power hunter RT for 300 and sold for 900 next day because they were brand new. My friend owns a truck shop so i bought new fuels through him for a deal then slapped on some marketplace tires
@@tippy8358 u can laugh all u want i found some fuels on facebook that were new for 400 dollars with new tires all mounted so u can say whatever but ill stick with saving 4k on wheels
@@x-i-clap-ttvs7876 and I’ll stick to my 15k forces
I just bought the Venom Power Terra Hunter XT 33x12.50r20 load rating 119, they drive really well, I notice that on the tire cold it say 80 PSI, my TPM in the Silverado indicate 40 psi, I just got them installed, so my question is at what PSI you keep yours cold?
Looking for some 26 in flat wheels for Ford. F250 no poke out no lift
hello i was told if i put bigger than a 22 inch rim on my 2024 gmc 1500 slt my front end would go bad and gear ratio change
Bought a set of wheels and tires one time for a vehicle didn't take into consideration the offset. So they mounted closer to the suspension than would have liked lol. Lesson learned
Looking for some 24-in flat wheels for a 2004 f250 8 lugs
Im putting 2.50 leveling front, 2inch rear leveling kit on 2022 z71, it has 20x9 factory wheels. Will 33-12.50-20 fit and what off set do i need for poke to be 1 inch or less outside of fender?
Getting a 7in lift kit with 24x12 tires on my 2018 Chevy Silverado 2WD do you think it will rub ?
Depends on the size of the tires, Check out the gallery for fitment help! www.customwheeloffset.com/wheel-offset-gallery
Did you regear your truck?
And here I am, just received my new wheels today… let’s see how this goes
And how did it go?
@@robertpawelek not that bad, I had recently replace tires so I just bought the wheels, finding a place to swap the tires on the new wheels was a bit of a challenge, and couldn’t find a place to install the leveling kit. One guy quoted me 850.00 for swapping wheels and installing the leveling kit. I ended up installing the leveling kit myself and between tires/TPMS swap + alignment was around 270.00
@@VortexVibe634 Nice! Hope you like the new look. I installed my own leveling kit as well, couldn't stomach the thought of the cost at the shops around town. Extra cash to put towards my new w/t setup now 😎. Hope to make a decision soon...
@@robertpawelek Thanks, looks great! I uploaded pics their gallery but can’t find them 🤔
How do you know the hub of your after market wheels will fit for sure?
My biggest mistake was letting my local garage put my tires on my new wheels, did great putting them on, not so much taking them off, scratched to hell in the first 6 months ive had them, im going to be touching up the paint on them myself
Well u scratched them…. Or did u mean they scratched them when putting the tires on
@@JameGoFast27 the garage guys scratched them when taking my old tires off
@@anytimefishing3870 ohhh that sucks
i have a leveled 2016 ram 1500 4x4 with factory 20x9 wrapped on 35x12.50x20 and i want to purchase some wheels and want to go with some 20x12s -44 would it actually rub more cause i had to trim a little ?? thanks
Dustin is a beast in front of the camera! He needs to be hosting TMZ or some shit!!!!! 💯
rotiform jdr on my f150 the hub bore is the same and bolt pattern is the same should i send it and get a set
I recommend following Dustin's advice
I like this guy because he has a Charmander tattoo and that automatically makes him awesome 🤘🏽
Just got my wheels n tires 8 days after ordering. Couldn’t be happier with the service.
my mistake was not ordering from custom offset but really is hard to find a affordable 20 inch for 1980 chevy c10 5 lug
Check out all options here tons of affordable options for a 1980 C10! www.customwheeloffset.com/store/wheels?sort=plh&saleToggle=0&qdToggle=0
i have a 02 ford ranger and i don't want to blow money on tires then have to get a lift
Do you guys ship wheel and tire packages (mounted and balanced) to Canada?
Look for yourself
World wide my dude 😎
Can you guys get fury county hunter mt 33x14.50x24 tires? I haven’t seen them on the website in months..
Not at this time, but we got venom power's! www.customwheeloffset.com/store/tires?sort=instock&diameter_from=24&width_from=33&ratio_from=14.5&saleToggle=0&qdToggle=0
Literally went out to measure my “33x12.50” cheaper brand tires and yup we are missing 3/4 to an inch in diameter.
Is it really free shipping?
I just got 22x12 to sit inside a 35x12.5 6in lift
Hey guys how are those venom tires
Are they loud?
And how are they in the snow and in the rain?
Great tire for the price point. They’re not loud. But you will hear them hum with the windows open
@@CustomOffsetsTV o ok kool thanks for the reply BROTHER
Is it safe to use Hub Centric rings for my wheels when off roading? Center bore 77.8mm to 110mm
Yes it is
That I could of just bought a leveling kit to fit 35s on the truck
Biggest mistake was not knowing the correlation between load index and load range. My truck calls for Load Range D but does not specify load index. So I got some 35x12.50R22 117 Load index Load Range E, thinking they would be fine. Well, they would be, if I wanted to run them at 60PSI. But the factory tire pressure is 42PSI. So for this size, I need a 127 Load Range F. Why F? Because all that the letter indicates is the maximum acceptable pressure. For example, the 121 Load Index Load Range E has about the same load capacity at 42PSI as a 127 Load Range F. This is because the load index is calculated at the MAX PSI. For LR-E it is 65PSI for tires like these, and LR-F is 80PSI for tires like these. SO when you do the calculation, a 121 Load Index with Load Range D has MORE load carrying capability at the same PSI than a 121 Load Index with Load Range E. This is because the 121 load rating is now measured at 65 PSI rather than 50PSI. The only benefit from a higher load range is that you get to run the tire at higher PSI and because of that, you end up getting more load carrying capability. but ONLY NEAR max PSI. So now i have to dismount and remount new tires and rebalance that meet the load carrying spec for safety.
I hope that made sense because it took me a while to realize this lol
Biggest mistake was thinking I knew what I was buying when I didn’t because rn I have 20x10s but they are going to be my winter wheels and I already have my 24x14s ready for summer
I bought a set of 35 16 16.5 boggers and I mean no one would mount them for me I had to go to a semi tire shop to get them mounted
Dustin my guy when you gonna fix the missing part that separates your headlights messing with my ocd
Spring time would be my guess, Dustin isn't driving it too much this winter, so not high priority right meow!
Should have gotten 17s with less offset instead of the 20s with the semi aggressive offset that I did 🤷♂️
Welp… drove an hour after convincing the guy to sell me wheels and tires he was gonna sell to someone else I paid extra thinking they were pro mags they were actually black painted trailer wheels and tires. I was pretty bummed now I’m stuck with them(:
I’m glad I watched this video. Might have avoided a big mistake. I bet a lot of ppl wish they saw this before they bought wheels and tires.
Biggest mistake I made...not getting enough double stuffed OreoS!
On a side note...looking for a nice set of wheels and tires for my F350 4x4 C C. L.B. I will know them when I see them
dustin is really good at his job lol
Biggest mistake I ever made was buying super swampers for my daily driver YJ.
Lol continue, how was it
Biggest mistake that I made was when I thought I could put truck wheels and tires on a car!😂 A big WTF moment!
Mistake was buying cheap tires , nitto and toyo from here on out
This whole trying to find out what tires real diameter is confusing. Then you go to gallery and you have guys running the exact same setups one says minor plastic trimming other one says major metal trimming.
It'll all depends on the lift,wheel offset,tire height.
I had the shop mount 22s on a 2007 Chevy Silverado and had to do mayor metal trimming they look awesome though.
The exact tire 285/55/22 -44 offset nitto Terra grappler,6 inch RC lift .
@@12arney I get that. I said exact same setup same brand lift same wheel and tire.
@@tonysilveira30 honestly ,it might be that some of the owners don't really have a clue of what had to be done to fit that set up and the ones that actually tells you what was done those might be the ones that did work on it.
Going to a non reputable shop to buy wheels and a lift I had a 3 inch lift and 20x8s after I paid for 20x12s and they wouldn’t change them or give me my money back 😂
talk to your social meadia or even better someone on the streets based on thier experience to make a decision on a lot money . custom offset has failed to mention that 20x12 will work for my application only after 20x10 has been shipped and installed now i’m having to save to get 20x12”s to fit my liking and application to begin with
lessons learned knowledge is power and can possible save you a lot of money dont listen to sales as they want your money and be out
lol.. I am 52 and I have never set an alarm since grade school.
I'm surprised bolt pattern isn't in here. But pros likely wouldn't make that mistake I suppose.
Can Custom Offsets be contacted for a free quote?
Absolutely, we also list all prices right on our website man!
@@CustomOffsetsTV I've seen that, but not exactly sure what wheel offset I may need.
Biggest mistake? I should have bought 22’s or 24’s instead of 20’s🤷🏼♂️
Bruh, I'm in that same situation rn lol. Got 35x12.50 22x12s over 24x14 last year cus I felt 24s were too big. Huge regret, now I'm in the process of buying some 24x14s wrapped on versatyre mt 36x14.50.
Clean them up nice and sell them. Buy the set you want ! 😁
Noti Gang late af! 🤦🏾♂️
Damn Dude you bounce around a lot!
That’s cocaine
What's wrong with the Double Stuffed OREOS ? Great video !
Everything. I feel like I got douped out of Oreos!
I bought a set of rockstar rims. Enough said.
Fabtech's proprietary technology for their front shocks/coilsprings
Always buying smaller than I want lol 😆
Mistakes I make. Watching videos that take 7 minutes to even get to the point if the video. Lol. Jk. Great video man.
I need to make payments lol on some 24x12s
We offer financing 😉 www.customwheeloffset.com/financing
That’s a nice Justin fio hat 🧢
Yall be taxing on the tires 😂
Noti gang pt5
Another one that no one tells u big wheels example 24X14 is fucking up ur suspensions 🤦🏻🦅
Not really true. Large wheels don't screw up your suspension, but it can accelerate wear on already failing components like ball joints or wheel bearings. -Fuller
Can't wait for my wheels! Someday lmao
Bro, you look like that guy from pawn stars Cory.
Dont forget speed rating...
Trusting the CO gallery.. yall don't verify shit.
YOU CANNOT fit a 22x12 and 37s on a 19+ Ram HD with a 4" lift with NO trimming and No rubbing . It's not possible
"if you're ok with a little bit of rubbing or trimming" youll want to run 22x12 with 35x12.5 tires for that aggressive fit.
I can't remember the last time I got taxes back. I am one of the few suckers that actually has to pay income tax. Pisses me off. All these people saying I need to pay more when they pay none. Sorry man just drives me nuts- BTW if you are getting money back instead of breaking even you are doing it wrong. Only mugs give the govt their money to hold on to- Everytime I see someone bragging about getting a big tax refund every year I just want to tell them how stupid they are for doing that and I lose respect for them
Leave me and my double stuff oreos alone.
Double stuff or bust -Dustin
There is no point in balancing a checkbook in 2022... it's called online banking.
Day 92 of asking custom offsets for a company dually truck build
The woes of a mall crawler... So sad
Too big offset
My buddy made a mistake. He said he wanted a Toyota tocoma
Dude is way to hyped.
Biggest mistake, buying tires not know not all run true to size
What the heck is wrong with double stuffed Oreo'S?
The dude needs a rehab stay for white powder.
Those lifted trucks on low profile tires look so stupid. Biggest mistake you could make.
They actually look the best. It's all a matter of taste lol
@@Connor4x4 when car enthusiasts, truck enthusiats, and normal people come together and say your truck is ugly, it's ugly.
Fitment industry ahh video
Did Dustin get new tattoos?
Hard to keep up lol
Yeah looks like he has hundreds 🥴
Couldn't help but notice after he keeps bringing his tatted arm across his body to show it off. Notice how every movement the tatted arm moves across the body to show it off and the other arm does not. Lol the little things 🤣
Day 136 of asking co for black and milled davincis
Hi
This guy is the shit
F 12ply 🤟🏼
Is having a tax professional file ur taxes and getting you more money legit
Also safer
👍👍
Yessir
Venom = junk
why you say that? on 33x12.50?
Got to give a little more info Than that.
Not looking for a crack on the lip
church? lmfao lord and Flavor cheese and rice
Bought Federal Couragias.... RARARARARARARARARARARARARARA.... sumbitches are loud AF on pavement.
But damn do they look sharp
@@CustomOffsetsTV definitely a attractive MT.
Dang get off the caffeine. The content is good but I can't take the yelling
Make side walls great again. It’s as if truck guys are going through the early 2000s fast and the furious trend. 🤡🌎