Thank you so much. Please people be prepared these wheel bearing on this car can be a nightmare. Took me 3 hours to swap for a new one. I really appreciate people who put videos on TH-cam thank you
Genius, in another video you hit the bearing with a hammer, I try for 3 hrs and it didn't move at all, but after I saw this other way, it was so easy that I change both sides, thanks a lot.
It’s much easier and cheaper instead of buying new tools for it 🤣 like I said just flip it around and get two lug nuts and bolt it down then go behind that wheel and belt it with a sledge hammer
Well I've finally done it on my own 107. Have to say thats a lot Anton for the videos, they were definitely useful and well made. Especially useful was that breakshoe video which was a much needed god send. I kind of wish i'd been able to make a video myself to cover my own experience, but I'll add a few pointers on here that may be of use. So I had a really rusty hub and really rusty wheel itself at the back meaning I had to use a sledge hammer and blow torch just to get the bloody wheel off itself. The front plate came off surprisingly easy, but the hub was ridiculously melted on. I had to take off the brake shoes and created a make shift part out of a socket and a bolt to do a similar thing. It was hard to get it just right. What I didn't anticipate though was not being able to remove the bolts from the old hub properly when they went in far enough. It's also hard without an electric tool as well because the hub spins freely so you can't get that torque. I managed to crack one side and then the other side with pressure, then used the sledge hammer to completely knock it off. The rust was severe. I even got some of that Rost Off spray. I had (not so much) fun taking apart the brake shoes and putting it back together only to realise that they didnt work at all. Lucky after some closer inspection I noticed that the horizontal bar with the adjuster on it hadn't been correctly seated in the brake shoe itself and when it was pushed to one side, it was simply sliding over the brake and not pushing it so nothing was happening. Managed to fix that and now the car sounds completely silent in comparison. I've only had the car just over a month and it was like this when I bought it so I've never had it so quiet.
Really enjoyed the video. My Toyota Yaris started to make a noise late last year. I thought at first the exhaust was starting to blow. The had only covered 38,000 miles. My local Toyota dealer diagnosed a rear wheel bearing problem. Repaired under warranty. Unfortunately they changed the wrong side first go. I think hitting so many potholes in the road wore the bearing out early.
The usual fault is water ingress, especially if the vehicle has been driven through water, ie flood or fords etc, the bearing cools rapidly and draws water in past the seals, great they changed them for you, the Yaris is a great car Thanks for the great comments👍🏻👍🏻🛠
Hello Fella. Great video as always. I've got the Milwaukee ratchet, great bit of kit as u say. I've also got the M12 3/8 impact gun from Milwaukee. Your big Milwaukeeis the M18 I take it? Nice bit of kit. They make things so much easier when doing repetition work. But the big gun in impact gun's for me is the 18v Dewalt which I have. Up to the individual I guess, but I do like the big Dewalt. Av a great weekend. Looking forward to surviving the L200 up to Leicestershire for my coffee or 2 🤗🤗🤗🤗🤗🤗 Stay healthy. Stay safe. Alan L200
Thanks Alan, the dewalt impact I believe has many shared components with the Milwaukee, and are both more the capable to tackle most nuts and bolts, The ratchet is beautiful, I have been more than pleased with it using it every day with no issues. The Coffees should be flowing within the next couple of weeks I will keep you updated, Thanks for the great comments👍🏻👍🏻🛠
I release the wishbone on the aygo gearbox and clutch videos, then its just the two mounting bolts and its out, the first aygo video I did without a balljoint splitter as well Thanks Garry for the great comments👍🏻👍🏻🛠
Question here - if I only just realised on my wife's car that the O/S front wheel is chirping how much time I have left before I have to change it? Not worried about the price of the part more about the fact in that I have to do the swap on my driveway.
I did a video on them, Link is th-cam.com/video/IjdEhu_2j3w/w-d-xo.html , They are ATS cup juniors, you can still get new abs cups they look stunning, and have a wider lip, Thanks for the great comments👍🏻👍🏻🛠
Hi great video. Can you tell me what are the model numbers for your Milwaukee impact and ratchet please interested in purchasing them on the back of your videos
Link for the Impact gun is amzn.to/2Zeaodo, and the ratchet is amzn.to/2C13hMt, Videos on both also are th-cam.com/video/WooDRNITGvE/w-d-xo.html and th-cam.com/video/exZgvVJUD3c/w-d-xo.html Thanks for the great comments👍🏻👍🏻🛠
Have you come across something called a "Slide Hammer"? I've been looking at these tools and wondered if this would be useful to get the hub out easier. I'm just worried about getting one and it not fitting correctly. I've seen one called a vidaXL Nine Ways Slide Hammer that looks like it might fit.
Thanks Scott, the one I said I was going to get but still haven't is amzn.to/2OtgtMF I will deffo get one when they come back in stock, Thanks for the great comments👍🏻👍🏻🛠
hello congratulations for the videos, I wanted to ask you if it was possible in your opinion to put the speakers on the door panel of the aygo, in a model that does not have the predisposition. thank you so much
Yes, absolutely, most of the higher spec models are fitted near the bottom of the door behind the door pocket, but you can retrofit with no issues, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 but should I create the cable that connects the speakers to the radio? or is there already? and in addition should you change the door panel and put the one with the right crate?
@@alessandropilla4368 it's an old question but you may still need an answer. Yes, you can retrofit one in the door bins or like I did on the plastic side of the door trim just by the seats. The cabling has to be done by hand but not as fiddly as you may think. Can be done within a few hours.
Yes Sorry forgot to add the link, This one is a beauty, and is low entry for the lower cars amzn.to/3iNJIrz, or a budget set something like this amzn.to/2W9fJAC, Thanks for the great comments👍🏻👍🏻🛠
Thank you so much. Please people be prepared these wheel bearing on this car can be a nightmare. Took me 3 hours to swap for a new one. I really appreciate people who put videos on TH-cam thank you
Thanks for the great comments👍🏻👍🏻🛠
shared a link to bug club fb page, this channel is gold for the c1/107/108/aygo owners
Thanks appreciate your share, Thanks for the great comments👍🏻👍🏻🛠
This is a great video. I need to replace mine and this is a big help. Thanks for the guide!
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
Genius, in another video you hit the bearing with a hammer, I try for 3 hrs and it didn't move at all, but after I saw this other way, it was so easy that I change both sides, thanks a lot.
Nice work! Thanks for the great comments👍🏻👍🏻🛠
You could have bolted a wheel the opposite way around and smacked it from behind with a sledge mate. It’s what I did and worked a charm
Thanks for the great information👍🏻👍🏻🛠
@@aaanton11 no worries bud
It’s much easier and cheaper instead of buying new tools for it 🤣 like I said just flip it around and get two lug nuts and bolt it down then go behind that wheel and belt it with a sledge hammer
I love your c1/107/108/aygo repair videos.
Glad you like them!, Thanks for the great comments👍🏻👍🏻🛠
Well I've finally done it on my own 107. Have to say thats a lot Anton for the videos, they were definitely useful and well made. Especially useful was that breakshoe video which was a much needed god send. I kind of wish i'd been able to make a video myself to cover my own experience, but I'll add a few pointers on here that may be of use.
So I had a really rusty hub and really rusty wheel itself at the back meaning I had to use a sledge hammer and blow torch just to get the bloody wheel off itself. The front plate came off surprisingly easy, but the hub was ridiculously melted on. I had to take off the brake shoes and created a make shift part out of a socket and a bolt to do a similar thing. It was hard to get it just right. What I didn't anticipate though was not being able to remove the bolts from the old hub properly when they went in far enough. It's also hard without an electric tool as well because the hub spins freely so you can't get that torque. I managed to crack one side and then the other side with pressure, then used the sledge hammer to completely knock it off. The rust was severe. I even got some of that Rost Off spray.
I had (not so much) fun taking apart the brake shoes and putting it back together only to realise that they didnt work at all. Lucky after some closer inspection I noticed that the horizontal bar with the adjuster on it hadn't been correctly seated in the brake shoe itself and when it was pushed to one side, it was simply sliding over the brake and not pushing it so nothing was happening. Managed to fix that and now the car sounds completely silent in comparison. I've only had the car just over a month and it was like this when I bought it so I've never had it so quiet.
sounds like you had fun!! great job Thanks Scott for the great information👍🏻👍🏻🛠
Really enjoyed the video. My Toyota Yaris started to make a noise late last year. I thought at first the exhaust was starting to blow. The had only covered 38,000 miles. My local Toyota dealer diagnosed a rear wheel bearing problem. Repaired under warranty. Unfortunately they changed the wrong side first go. I think hitting so many potholes in the road wore the bearing out early.
The usual fault is water ingress, especially if the vehicle has been driven through water, ie flood or fords etc, the bearing cools rapidly and draws water in past the seals, great they changed them for you, the Yaris is a great car Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 Thank you for that information.
Thanks for the video ! iv just had my front left wheel bearing replace it was ceesed . Nice to see you go through it all.
Thanks John for the great comments👍🏻👍🏻🛠
Hello Fella.
Great video as always.
I've got the Milwaukee ratchet, great bit of kit as u say. I've also got the M12 3/8 impact gun from Milwaukee. Your big Milwaukeeis the M18 I take it? Nice bit of kit. They make things so much easier when doing repetition work.
But the big gun in impact gun's for me is the 18v Dewalt which I have. Up to the individual I guess, but I do like the big Dewalt.
Av a great weekend. Looking forward to surviving the L200 up to Leicestershire for my coffee or 2 🤗🤗🤗🤗🤗🤗
Stay healthy. Stay safe.
Alan L200
Thanks Alan, the dewalt impact I believe has many shared components with the Milwaukee, and are both more the capable to tackle most nuts and bolts, The ratchet is beautiful, I have been more than pleased with it using it every day with no issues. The Coffees should be flowing within the next couple of weeks I will keep you updated, Thanks for the great comments👍🏻👍🏻🛠
Excellent job!
Thank you very much! & Thanks for the great comments👍🏻👍🏻🛠
Very helpful video, thanks! Wouldn't it have been easier and quicker to use a bearing puller, or are they not recommended, for some reason?
you could if you have one, Thanks for the great comments👍🏻👍🏻🛠
Great Video again Aanton. Allways easy to understand. Have you ever done front wishbone ?
I release the wishbone on the aygo gearbox and clutch videos, then its just the two mounting bolts and its out, the first aygo video I did without a balljoint splitter as well Thanks Garry for the great comments👍🏻👍🏻🛠
Just watched your aygo gearbox job was a bit of a bugger lifting the gearbox good little cars the aygos c1 107
I am not as strong as I used to be, it was a struggle lifting the box, Thanks Mark for the great comments👍🏻👍🏻🛠
Hi again, have you ever changed the gearbox cables that run to the gear leaver
not needed to Gary, bit its not too bad a job, Thanks for the great comments👍🏻👍🏻🛠
How long did it take to do this job iv got to change one myself outside so just wondering thanks
a couple of hours, Thanks for the great comments👍🏻👍🏻🛠
Great job.
Thanks Tahir for the great comments👍🏻👍🏻🛠
Question here - if I only just realised on my wife's car that the O/S front wheel is chirping how much time I have left before I have to change it?
Not worried about the price of the part more about the fact in that I have to do the swap on my driveway.
Have you got a stone stuck behind the brake back plate? Thanks for the great comments👍🏻👍🏻🛠
are the wheel bearings from Aygo the same as the 107?, great video matey
Exactly the same Thanks for the great comments👍🏻👍🏻🛠
I saw a forum post about turning off the seatbelt reminder chime. Could make a good video
I will look into it Thanks for the great comments👍🏻👍🏻🛠
Hi Ant, What make are those wheels? I wouldn't mind some myself. Are they expensive? Good vid btw . Cheers
I did a video on them, Link is th-cam.com/video/IjdEhu_2j3w/w-d-xo.html , They are ATS cup juniors, you can still get new abs cups they look stunning, and have a wider lip, Thanks for the great comments👍🏻👍🏻🛠
Hi great video. Can you tell me what are the model numbers for your Milwaukee impact and ratchet please interested in purchasing them on the back of your videos
Link for the Impact gun is amzn.to/2Zeaodo, and the ratchet is amzn.to/2C13hMt, Videos on both also are th-cam.com/video/WooDRNITGvE/w-d-xo.html and th-cam.com/video/exZgvVJUD3c/w-d-xo.html Thanks for the great comments👍🏻👍🏻🛠
How do I work out which side is bad? Got a loud humming that reduces on a right hand bend.
Jack the car up and spin the wheels you will hear the rumble on the bad side, Thanks for the great comments👍🏻👍🏻🛠
Just a quick question. At 13:30 why don’t you hammer something between the back plate and wheel bearing to try and pry it off? Genuine question👍🏻
The back plate is really soft and easy to damage, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 Okay. Tah pal! I’ve always used a really wide bolster chisel😂.
Use a bolt for remove the breake drum, there is the thread. Is easier than hit it.
Thanks for the great information👍🏻👍🏻🛠
I what is do at this type of bearing is putting the weel back on it and slam as hard as you can on the wheel
Thanks for the great information👍🏻👍🏻🛠
You. Could have copper greased the new hub. Prey for the next guy to do the wheel bearong
That Guy will be me 😂 it will be fine, Thanks for the great comments👍🏻👍🏻🛠
How did you know if it was front/rear or left right?
if you jack up each wheel and spin it you can hear the rumble, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 it rumbles at both sides!😳
Teşekkürler 🙏
Thanks for the great comments👍🏻👍🏻🛠
Alright ant. The last 1 I did I had to remove the shoes and air chisel it off. Bloody things
I thought this one was going to be easer than the last one, how wrong was I, The hammer won in the end lol, Thanks Ken for the great comments👍🏻👍🏻🛠
could you use a slide hammer to get wheel bearing off?
yes it could help remove one that is stubborn, Thanks mark for the great comments👍🏻👍🏻🛠
Ciao, come si chiamano i cerchi in lega che ci sono sulla peugeot 107
Thanks for the great information👍🏻👍🏻🛠
Have you come across something called a "Slide Hammer"? I've been looking at these tools and wondered if this would be useful to get the hub out easier. I'm just worried about getting one and it not fitting correctly. I've seen one called a vidaXL Nine Ways Slide Hammer that looks like it might fit.
Just realised you mentioned this on the other vid you did.
Thanks Scott, the one I said I was going to get but still haven't is amzn.to/2OtgtMF I will deffo get one when they come back in stock, Thanks for the great comments👍🏻👍🏻🛠
A bit of sandpaper on the shoes and inner drum wouldn't have gone a miss but good video
Thanks Pal for the great information👍🏻👍🏻🛠
hello congratulations for the videos, I wanted to ask you if it was possible in your opinion to put the speakers on the door panel of the aygo, in a model that does not have the predisposition. thank you so much
Yes, absolutely, most of the higher spec models are fitted near the bottom of the door behind the door pocket, but you can retrofit with no issues, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 but should I create the cable that connects the speakers to the radio? or is there already? and in addition should you change the door panel and put the one with the right crate?
@@alessandropilla4368 it's an old question but you may still need an answer. Yes, you can retrofit one in the door bins or like I did on the plastic side of the door trim just by the seats. The cabling has to be done by hand but not as fiddly as you may think. Can be done within a few hours.
Can you buy bearing pulling machine
Like this one amzn.to/3GvA0YJ Thanks for the great comments👍🏻👍🏻🛠
have you got a link to the trolley jack pls?
Yes Sorry forgot to add the link, This one is a beauty, and is low entry for the lower cars amzn.to/3iNJIrz, or a budget set something like this amzn.to/2W9fJAC, Thanks for the great comments👍🏻👍🏻🛠
I know your a tech as your full time job is the company u work for in your channels name I understand if u don't wish to comment
Great Spot 🧐 This video sad as it is is how it all started for me th-cam.com/video/dMnUqY5FunI/w-d-xo.html Thanks for the great comments👍🏻👍🏻🛠
👍👍🇵🇹🇫🇷
Thanks for the great comments👍🏻👍🏻🛠
Nice video! I hope you'd enjoy my videos too. Keep up with your fantastic work! 💜💜
Thanks for the great comments👍🏻👍🏻🛠 n
Those wheels are wicked. Did you have a link on them?
Best regards
Here is the video th-cam.com/video/IjdEhu_2j3w/w-d-xo.html Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 many thanks!