4.2 Range rover/Jag supercharger removal/ rebuild and parts list
ฝัง
- เผยแพร่เมื่อ 13 มิ.ย. 2020
- pt1 removal of M112 eaton super charger from 06 range rover, same engine as the jaguars as well
SUBSCRIBE PLEASE
PARTS LIST
Square top super charger seal 1347543
Rear horn gasket 71841QJ
Intake Duct x2 4628214
Throttle body gasket 4536886
Coolant square O rings x2 4413478
Charger vane needle bearings F390978 FC65477
Coupler Rebuilt kit www.ebay.com/itm/Jaguar-Land-... - ยานยนต์และพาหนะ
Thanks for making this video, much appreciated.
Thanks for the insight. Liked the simplistic approach. Working on 08 xjr coupe. Slightly different set up but similar accessibility issues
This has been very helpful, I have this motor in my 03 jag s type R. Changing the throttle body out this weekend & will use this video as my guide. Thanks again. Might use this for the super charger at a later date also 👍👍👍
Great video best iv seen for this job I'm doing my snout bearings at some point and this has been helpfull
Ďakujem za video moc si mi pomohol
Thanks for the video. Way better than alldata.
Thank you!
I have check now P0441 and I have to clean or change evap valve.I just don't know how to get to this valve because it's behind the throttle above the transmission basket.RRS 2006 4.2 sc.I was trying do it twice but couldn't:(
you don’t need to remove the water passages at all to remove supercharger, the pulley fits right through the hole with some wiggling
Thanks for the video. I’ve got a nasty squealing sound on acceleration over 2500-3000 rpm on my 2008 4.2 SC 134k mi when in Drive (not as loud or prevalent when shifting manually). Thinking its the snout bearings but still no major idle noise (perhaps a slight knock/tick). I replaced idler and tensioner pulleys and have all new belts. New ac compressor & condenser too. Other than snout bearings, is there much else to consider on the supercharger that could cause this?
I dont get the noise when downshifting (no accelerator input) but this would be normal. And when downshifting the engine and tranny sound great. I want this healthy sound all the time! Thanks
Thanks for posting this. I have a 08 SC and this might come in handy some day. What exactly had to be done to the SC? Replace just the pulley or also some bearings? My car runs great and I love driving it. Some minor issues like intermittent wipers don't work and driver's seat back cooling not working. I also get an intermittent CEL: Low catalyst efficiency, left bank. Car runs fine though. Merry Christmas and have a good 2021.
PS: you can download the L322 service manual from the net and it is pretty good.
The snout bushing was shot, causing a rattle at idle, you can see it in the second video, while it had it out i did all the bearings and seals. I would start with a tube up, i often find that fixes alot of cat issues. Merry Christmas!🎄
@@nsigarage5212 Thanks for the reply. I will have to keep that in mind.
men please answer my question whats is in the black box which is on your left side, that box positioned after right headlight, please i can not find answer thanks
Hey is there any chance you continued and replaced the hoses under the charger while you had it out? I need to replace that on mine and would love to see it if you have pictures or a video of that also.
Just a thought on that coolant manifold you struggled to get out. Couldn't you just separate it at the thermostat and move the piece out of the way rather than removing the whole thing? I mean, it's a good thing to replace those o-rings...
I sorry but I did not
My mechanic just did this to my 4.2 sc about 6 hours start to finish he did not touch any part of the cooling system and the sc just slipped straight out. Good guide tho
6 hrs is about what it took me. This was actually my first time doing to Job. Next time I will explore that option further as it was the hardest part lol
Hey there, this is a great video and I am in the process of gathering all these parts. I have the new coupler kit from eBay but all of these parts you list do not seem to be Land Rover part numbers. Where did these part numbers come from? I've tried google and a couple of them cross reference but several do not. I even went to my local Range Rover dealership and they do not recognize these part numbers. Can you help?
thats really weird, but i have gone though it and have updated the list, let me know if you need help with anything else. i must have gotten them from 1 particular site that no longer exists, as i tried to make it so people could get all the parts from as few vendors as possible.
I have a hose that is ripped from what seems like behind the left side of the engine if your face towards the engine, cant see it, not sure if I have to do all this process just to replace that hose. antifreeze
That I'm not sure. It's been so long sense I worked on one of these engines let me know though
how long did it take you to do this job? looks painful.
Out, rebuilt and back in was about 6 hours. Not to bad considering this was the 1st one i had done
I would like to know how to change the water pump and thermostat on a 2008 land rover range rover Sport supercharge
Alldatadiy.com should help you out. It's the same program professionals use. Expect you pay for all the info on just 1 car
Do you have a video on how to replace the fuel injectors?
I'm sorry but I dont.
how come your doing this? got any lean code experience with this engine?
No codes, top end had a clattering sound at idle, dealer misdiagnosed as timing chains. In the second video it shows the super charger breakdown and were the noise is coming from
@@nsigarage5212 ahh the plate yeah. fair enough thanks :)
I was wondering why my car is completely different from the engine compartment? I've also 4.2 SC -06 Range Rover Sport. I don't have as much space there than you have in this video.
same motor, but this is the big range rover, not the sport.
@@nsigarage5212 okey that explains. RRS is then very much different 😀 It’s not so easy job 🫤
Can you add this Supercharger on a 4.2l regular motor
No. They didn't make a 4.2 non super charged. It was a 4.4, very different
My bad that what I mean ,I have the 4.4 can it be added to it
And if not would it be a big problem if I changed motors? Thanks for the information
I have never seen anyone covert one to a super charged version, in my honest opinion for all the time and money needing in that, not to mention idk if things like the axles or transmission, cooling systems, wiring harness, computers ect. I think the best idea would be to buy one that was super charged from the factory. Or try to find a company that makes a kit
@@nsigarage5212 ok. Thanks
Nice time with your work but camera not clear on the job
I apologize, it was my first video, and at the time I was just a laptop with Webcam on a 20ft USB cable. If you have any questions on the repair please feel free to email me at Nosleepinc2020@gmail.com
@@nsigarage5212
Can i get the diagram for supercharger 2007 range rover sport
Having problem with backside of the super charger (EGR) I forget thier places,how the wire and hose goes
Can you help out
What year is your rover, and is it the big one or the sport. You can also get all the info and procedures you need at alldatadiy.com
Mate, put the camera down….it’s not an action video it’s a tutorial
I know. It was my first video. It's a bit rough with just a web cam with a 20ft cable to a laptop, however if you would be kind enough to check out some of the other range rover video you will see thst has been greatly corrected
profishinal