The Complete Guide to Painting Steelies
ฝัง
- เผยแพร่เมื่อ 5 ธ.ค. 2015
- In this video I show you how to completely repaint and restore your old rusty steel wheels to give them a new great look. I go through everything from prep work and rust removal to masking and painting techniques. This is a great home DIY project to make your old rims look great, and hold up to winter. I used Rustoleum Metallic Charcoal Stops Rust spray paint over Rustoleum automotive primer to get this great, shiny and smooth finish. The wheels are for my Volkswagen Rabbit. Recorded with a Canon t3i and edited in sony vegas. Thanks for watching!
Need paint for your wheels? Get it here! (Affiliate links for which I may be compensated)
amzn.to/2icMwEq
For additional content, check out www.cashedoutcars.com! - ยานยนต์และพาหนะ
Need paint for your wheels? Get it here! (Affiliate links for which I may be compensated) amzn.to/2icMwEq
I've done this a couple of times and I'd recommend deflating the tyre which opens up the gap between the tyre and the wheel. You can then paint further into the gap, then when the tyre inflates it covers the edge of the paint.
That's a good tip, thanks!
I paint for a living professionally and I find this video perfectly flawless..great job.
+Allison Hines awesome, thanks for the feedback!
+Mega Marowak early Miatas don't use clear coat at all
+Mega Marowak correct but why would you clear coat a fender when the rest of the car isn't clear coated? It wouldn't match and it'd look silly
luna indigo if you paint professionally you should know that you should always put clearcoat over raw paint to protect it and give it a good shine,I work with an professional car painter and I showed him this video and he said the same thing as I said,ALWAYS PUT CLEARCOAT NO MATTER WHAT.
+Matthías Little thanks for sharing the video! It's not always about shine but if you'd like to clear coat what you paint go for it, this video is for single stage paint
I like that you actually remove the wheel weights
Little tip, instead of masking tape around the lip, use standard size note cards.
sounds like a robot version of ChrisFix.
ed elsey best comment ever
LOL YUP. wHO DID IT FIRST?
This channel uploaded their video 13 days before ChrisFix, it's a shame this channel didn't get as much traffic as this one does a fine job of teaching.
@@rhubarbpie2027 yeah I agree but op is right he sounds like chrisfix
plot twist, it is chris fix
Great video, thanks man. Very solid, quality job. So refreshing to watch a TH-cam video with no embellishments.
When i painted my old car rims i had the car on jack stands and put the wheels on and had the car idling in 2nd gear while i painted, worked a treat
Nice! That beats the method I used: driving slowly with my wife running along side with a can of spray paint.
That is ghetto 🤙🤙
Excellent job young man!!
Really good guide and excellent results you achieved 👍
Thanks, now I completely know how to paint steelies!
Love this guy! Very straightforward, clear and no nonsense. Awesome!
I appreciate that!
Great video! Easy alternative to buying aftermarket rims, thank you.
You did a pretty good job thank you for the thorough explanation they look nice
Thanks!
Put some colored lugnuts to add accent to your steelies.. it also adds 5hp
Outstanding video and great job on the wheels.
+ArchimedeanEye thanks man!
They look damned nice for steelies. Great job.
Thank you!
Good job! Thanks for the video.
nice thorough job man... good-looking end product
+dirty Mushroom - Holly Bubba thanks bud!
CashedOutCars no prob
Looks super sweet!
Thanks man!
awesome job
I also have a 07 rabbit and I got rid of the Jetta rims that were on it before from the previous owner and went with the steelies. They look good on the car.
U killed a rabbit?
I have the exact car and im about to paint the rims on my snow tires 😂😂
Good job mate!
Nice Job Mate.
Baz (uk).
very informational. i have a suggestion for rattlecanning though. when you paint start from off your subject and end off of subject so your ends dont get too much build up
Good advice! That's what I try to do but for some parts on the large surface of the wheel that's difficult
Nicely done!
Great work.
That wax is a good idea (always is), nice upload.
+bfjb70 sure is. Thanks!
nice paint job well done my friend
Thank you very much!
Great video. Very detailed. And I don't think you sound like a robot! You sound like you CARE!
Thanks, I appreciate that!
Or a robot that cares. Like Sonny from I, Robot.
U are the best instructor mate , Good on nyaaaaaa .................. :)
Nice one buddy
I will now do this same technique with my chasers for my Vp
1:54 in and I’ve decided I’ll phone my powder coaters 😂
Nice video dude! I may do this on our Crown Vic.
Go for it! It makes a nice difference in look
Very informative bro. Thanks.
Glad you enjoyed it! I'm working on another similar video on steelies now since I just painted another set
CashedOutCars looking forward to it bud.
bro amazing job
Great video, thanks.
nice complete job 👍
+botelloheritage12 thanks!
Did a great job, came out looking factory.
Thanks!
I work in a manufacturing warehouse where we paint and laminate.. And we also have a Woodworking shop and a metal shop.. When you spray.. You are supposed to start and finish each stroke off of the rim.. And never in heavy strokes that close.. To apply light coats.. You spray around a foot away and when you want to apply heavier coats.. Always a foot away and just do each stroke a bit slower to avoid runs and orange peel.
Rayven Wulf thanks for the info
You can use playing cards wedged in the lip of the wheel for a quicker masking solution...works great.
That's really smart bro
I found it better to use an angle grinder on the surface to remove any rust. Just need to be careful not to contact the valve stem or the tire wall when doing it. The sandpaper should be the secondary step after angle grinding to smooth the entire surface out nicely. Also if you wedge index cards between the rim and the tire it forms an effective shield from overspray instead of having to use masking tape. But to each his own.
Yeah this guy pretty much removed none of the rust, you can see it there when he's using a scotch pad on the wheel.
Nice job. Here are a couple of tips I would use. Use 3x5 index cards around the bead of the tire to be your first method of keeping paint off of the tires. Let some air out of the tire and tuck in the cards overlapping all the way around the rim. If you still want to mask it off it makes it easier and less tedious. Next, I would use etching primer on the wheel, this makes a most excellent surface for your final color coat.
interesting spray technique.
I blasted only the part you see through the hubcap.... It was dark and I just finished fan belt and brakes. I'm laaaaaazy... Also a huge fly got caught on my rim and I ground it in and sprayed over...
Flawless!
Nice colour
do you need to paint steel wheels when you first get them? or only once they become worn?
Cash is pimping his ride!! Big Pimp'n!!!
Hahahah budget pimping over here
greaat job !
Those wheels are too nice to paint!
Actually thinking of doing this and adding duplicolor colorshift just for the fun of it
Would CLR work to remove the rust?
Great video!---Question, I would use a drill will a wire brush to first remove rust & sand paper for wher I can't get in with the wire brush. I'm sixty and my hands just don't have the strength I used to - you don't use the power wire brush - any reason why?
Thanks! You definitely could use a power wire brush, I just used the hand one to get in small areas and be as careful as possible.
If you have the compressor you can make a sand blaster for 5$ youtube pop bottle sand blaster. Let the air out of the tires and "mask" with index cards.
What grit sandpaper did you use?
Please tell me what kind of paint you recommend doing this job
Is there any kind of cap I can put in the center ? I want to remove my wheel covers
Quality job right there. Plan to do this to my Explorer interceptor steelies.
Thanks, enjoy your project!
@@CashedOutCars What grit sandpaper did you use and any particular scuff pad?
To be fair i like the matte finish
Excellent but what about the back side of the wheels, although never seen unless changing a tire they could be awfully rusty ??
How to paint from Inside ? Can you make a video on that as well
Looks great! I know this video is a few years old, but do you remember how many cans of primer/paint you went through? Was just one enough for all of the wheels?
I believe it used about one can of primer and two or three of paint, I believe two though. It depends how many coats you go for!
What kind of rust eater did you use?
well done
Thanks!
Nice1..Cashe & thank u
You’re welcome!
What grit you use for sanding?
Last step: slap some closed end chrome lugnuts on there. Nothing like contrast (chrome bullet tip airstem)
I agree that could be a great look!
I was hoping to find an easier way! Did it this way once and it took foorreevverr!😏
Nice job. How long did you wait between coats?
Go by what it says on the can you're using - it will vary based on the paint you buy.
QUESTION : what do I do if I need to make a touch up on the wheel after I spray painted and applied clearcoat? I basically spray-painted my wheels and got my wheels rebalanced (new tires) and got new wheel weights put on. there’s steel showing where the old wheel weights were. Would I simply just spray paint and clearcoat that one area? Would I have to sand and respray the whole wheel?
For a quick touch up, spray a bit of paint in a container and brush it on, followed by the same process with clear coat
@@CashedOutCars Thankyou!
Nice job on the wheels. I went through the work of doing this last year on a set of winter wheels. In the middle of winter I ran my car through a car wash. After washing, I did a walk around and noticed the paint was coming off the wheels ONLY by the zinc wheel weights. So frustrating after all the work of prepping/painting! I'm wondering if the zinc wheel weights were acting as an anode. Has anyone else had this happen?
Good question. Maybe adding a layer of fluid film / plastic coating spray to the wheel before applying the weights would help.
In my experience you should de mask the painted wheels (before) the pain has dried, as this gives smoother paint edges
Also use etch primer on steel wheels
Would you use a primer sealer after the etch primer?
@@jthet2001 That would only be necessary
if top coat or finish coat of paint is incompatible with the etch primer. Best to check this first with a test piece
for any adverse reaction between the two paints.
If I do this to my wheels will I still be able to wash them with normal wheel cleaning stuff or will it take the paint off?
+Jesse McClain you should be able to still use normal cleaners. If you're worried you could look into tougher paints, but I've had no problems with mine
Pro tip, instead of tape use a set of old playing cars. Slip one car overlapping the next in between the rim and the tire. Easiest way to do it with out removing the rubber.
Should've put a coat of clear.. How many cans for all 4 wheels?
hey buddy just wondered where did you get the center cap from?
+Bo these wheels actually don't have center caps, unless we're talking about something else
What's that shade on rims?
Just did this on my 2019 Elantra. Those plastic hubcaps looked horrible. The steelies look sharp
Nice, enjoy em! I agree
what are you using for center caps, to cover the hub?
I ended up making custom center caps, I have a video on my channel about them
Why don't you protect the inside of the rims with tape and paper too?
No clear coat? It's worth it, it adds extra protection and gloss makes the wheels easy to clean.
It's all personal preference, the process for clear coat would be the same. I personally like the bare paint, and after a winter of salt they still clean up super easily and haven't chipped or rusted.
Clear coat is smart idea
Nice job. Why didn’t you use clear coat afterward?
I liked the Matte look of the raw paint and ended up waxing them for a bit of protection
How much of a problem do I create if I do not mask off the rubber tire when painting black paint , rubber is also black! Does it hurt tire? Or is allowing overspray just look too tacky? Would be a lot easier? Also be easier if we demounted rubber tire, like at time when new tires r being installed!
I wouldn't spray right onto the tire since the texture and color won't be the same! The risk of painting before they're mounted is it can get scratched while mounting, but most reputable and experienced shops should be able to do that no problem
Need center caps and be looking great
What was the point of removing the wheel weights if you were going to paint them anyway ?
Where do I find center caps for steel wheels to cover the bore?
I made custom ones for mine! I'm not sure where you could purchase them
Awesome vid. Wonder what he’s up to these days?
I'm still around!
No clear coat? Nicely done paint job!
I didn’t clear coat mine and they held up for years, but clear coat will add an extra layer of protection!
Is there any product to avoid corrosion on a new one? What do you recommend for take care of them
If you want to avoid rust on new steelies, then make sure that road salt, debris, and mud get washed off at regular intervals. If you live in a state that doesn't salt the roads, you'll probably be fine for a very long time.
How long did this take u?
subscribed
Good job, too much work for some stock steelies for me lol
From vintage vehicles to modern ones, there are a whole bunch of people like me that prefer the original steel rims over any possible after market rims. They not only look the best to me, but hold a better seal than any porous metals like aluminum.
If I’m going to paint a rim that’s still good
It will look still good
Cool
What type & brand of lug nuts do u use on ur steel wheels?
+koolmuxmusic123 123 I just used the OEM ones that came on the car
you sound exactly like chrisfix , but great video .
+Eyad Jam haha I get that a lot, thanks!
@@CashedOutCars How many cans of spray paint did it take for u to do all the wheels?
Can I paint both side on rims or just the outer side?
+Jack Mok yeah you can paint both sides as long as you get all the brake dust and stuff off the inner part
My understanding of was is its acidic and holds the acidic crap from the road. Resulting in a leaching into and breaking down the paint/metal. Any thoughts?
What do you think is acidic, the salt / road treatment use on roads?
Wax is Ph of 8 or higher - stuff off the road; salt, calcum and bugs--- and its traped in the wax and gets even more acitic. If you look at a wax surface under a microscope - looks like a sponge. Anyone with an expensive sports car will never wax it.
@@DTGrosz Stuff and nonsense.
no clear coat?