I have both, ecu flash and bazzaz. Initially thought to go one or the other. Then dyno tuner recommended both. More torque and responsiveness from combination. Smoother also, from eliminated restrictions. 05' ZX10R. Thanks for posting!
From what I have been told is that a ``custom`` ECU flash with the bike set up on the Dyno during installation is the best all round solution. This as opposed to mailing off an ECU for a standard flash for your bikes mods. Its a little bit more expensive, but it brings out the best in the bike. My 2008 R1 with three quarter exhaust and filter made 170.4 HP at the wheel and 82.58 lbs of torque. This was done on a notoriously stingy dyno and of course does not incl Ram air effect which is worth about another 8hp at speed. My previous R1 with similar exhaust set up and PC3 made 165.5hp and 79.5 lbs. Stock Euro bikes typically make 158-162 rwp and 76lbs . Biggest difference over stock was the much nicer spread of torque, general drivability and removal of Yamaha`s first and second gear 60% power restrictions in first and second gear. That was via the ECU flash. The PC 3 was great too, but of course can not alter any of the bikes electronic settings.
Better have a smooth running engine than jerky O/I behaviour which also takes it's toll from the other mechanisms. Clutch, chain, pinions engine internals... without mentioning the unsafe power delivery if you happen to come across a slippery part of the road while cutting throttle or opening up...
Definitely flash. Especially the Ivan flash. Fuel tuners do just that and some can make minor timing changes. A good flash smoothness throttle, remove factory cutoffs, remaps your timing ALOT. And even let's you chang your fan temp controls. No question flash is always the answer
I picked the FTecu bike harness and just used power commander maps. Supper easy to install all you got to do is plug in 3 wired to the bike ECU harness and make sure you find a good 12.v ground for the ground wire. I like the engine breaking so I left that on but I lowered the temps at witch the fan runs at max to keep the bike nice and cool at stop lights on a hot day and its never been higher then 190.F since.
Most of these new ECU's can have their fuel maps adjusted just as well if not better than a powercommander. Some of the older bikes, it's piggyback or nothing.
It’s my understanding that who ever is doing the flash has control over all those aspects. All I am saying is they can tune in or out your desired engine braking, idle rpm and rev limit
Before I got my FZ-09 I had a 07 just like yours. M4 slip on exhaust with a fair amount of popping. Got my ECU flashed, worth it. Butter Baby...Butter👌🏼😉
It is a 2 step process. Do the base ECU flash to remove restrictions and then install the power commander or auto tuning kit to maintain better AF ratio. Not sure why this is so hard to understand.
Because people always look for the cheapest option possible. Paying for a ÉCU flash and installing a stage one kit is considered expensive to most. Maybe they should find another hobby ?
That is next level dumb. You can get a flash package like Woolwich racing that has auto tuning and data logging built in. You can flash the bike with the ecu installed. Piggy back systems like PCV are garbage old technology.
A note on your camera setup ..... I have seen a couple of videos where the ram X mount has "let go" of devices held in that orientation. It has to do with when / if you hit a rut in the road, the weight of the device pushes against the lower jaws which opens them. Perhaps add a case and tether for security? Just trying to help you keep hold of your shiny new Iphone 7Plus :-)
I had a Guhl Motors flash done on my ZX-14R, and the power increase was immense. The Fuel Commander can fail, and leave you stranded out of town, the flash is as reliable as the stock ECU. My bike was slow until I had the flash done. Good value!
KN, it was $375 at Guhl Motors, and worth every penny. Don Guhl is reflashing it for right now at no extra expense because I regeared to a 16 tooth ft. sprocket, this threw the traction control off. Ride safe.
I do agree with you ECU is more reliable. But if your PC ever fails you can unplug it and reconnect the original connectors (bypassing the PC, just like the stock configuration). It wont fix the PC but at least you wont get stranded
Doesn't seem like your in ca but I know removing the evap and air injection helps stop so much engine braking and no more popping i have a 15 fz09 and it was twitchy with ard engine braking the bike came flashed and I have a power commander its so smooth and I still have to dyno it
Yes You can flash to derestrict, makeotheradjustments, etc depending on which flash and what's available four your specific bike. Then you could just use pcv for af tuning.
An even better option is to do both!. Check out the Flash tune on Revzilla. Really easy to install and you get the best of both worlds. There is also an auto tuner you can get with it that will tune based on current conditions.
Here is a link. ftecu.com/shop/2015-yamaha-fz7-data-link-ecu-flashing-kits/ I got mine after watching a video about it by Jake the garden snake. No sending the ECU out to be flashed and no insane rewiring to do. It covers everything you are talking about with 4 connections into the wiring harness of the ECU.
A few things you said were a little bit off. You don't have to remove your ECU to flash it. You can do it at home with your ECU still in the bike. All sorts of programs are available depending on your equipment. A lot of them are available from places like FTECU.com. You can also have a professional custom flash your bike. The same is true for a Power Commander. On newer bikes you can adjust all sorts of settings within the ECU. It doesn't automatically cut off your engine breaking. That's up to the owner of the bike. A PC and ECU working together is actually the way to go for high performance.
I think that's what someone is saying reflash all the restrictions and use a pcv to tune air flow . I think I'm correct but hell what do i know I'm on here myself trying to figure it out and can't make head nor tail of it .it sounds to me like it boils down to people's opinions yet again like everything else in this fucking post . All the best .
The choices are very similar but you forgot to mention the added cost of a Power Commander v.s the already installed ECU. A Power Commander costs $360 and requires installation. A FTLink costs ~$50 but I can't find one for my motorcycle. For ease of modification, I'd opt for a dino verified ECU flash.
Is this like hacking your bike's software, and kind of dangerous to do? I hack phone software all the time but at least no one is gonna get into an accident when they use my flashed phone.
If the manufacturers didn’t restrict the performance from the factory they wouldn’t need to do this , unfortunately environmental bs and liability concerns prevailed
Can I choose neither and keep the bike running lean with backfire downshifting or will it eventually mess up my engine and (burn my piston rings) and what not
I say Ecu. and if you go to the ftecu get the bench kit. it's way better. this comes from a guy who got the bike side. I was 100% confident i can do that. well I was wrong
Stupid laws over in Australia state that for Restricted Open riders, we cannot exceed 150kw per ton power to weight ratio... and the MT 07 is already a bees dick off being over that. So having a tune could void my warranty and insurance if I have a crash. The only way to prevent that is to go onto an Open license, which requires another $300 riding course.
Or another of looking at it is they would rather a 17 year old with no experience not go out and jump on an R1 and kill himself in not time due to crazy power to weight with no skills, truly a recipe for disaster. A year is a reasonable amount of time to gain some road craft before riding a weapon. It is a lot better than before when there was 250cc limit. Kids went out and bought RGV's , RZ's and KR1's which while being fantastic bikes, they were also not good bikes to start on due to the power delivery of these bikes. It's now more about linear power that is easier to control so you can buy up to 660cc with power to weight of 150kw per ton or less. As far as the MT 07/FZ 07 is concerned there are 2 versions, a restricted and a high output model. The restricted version is sleeved to reduce capacity from 689 to 655cc. On the street there is not a lot of difference as while the high output version has around 78 rwhp and the restricted version has I believe around 42 rwhp the restricted version is pretty close in torque output and that torque is tuned to come in lower on the restricted so in effect it's not really slower at normal speeds, will be noticeable at higher revs however. The restrictions are throttle via a dog leg section on the throttle body which restricts the travel, this can be easily replaced. A airbox restriction which reduces air intake, this can be dremeled out and 5th and 6th gear are limited to i believe around 6000 rpm in the ECU so a flash is required to remove. DA2THFA1RY - As well as getting an open class license you would also need to re register the bike as non Lams and once this is done it can never been downgraded back which will affect resale of the vehicle given the market is a lot bigger for LAMS approved bikes, also as you state no insurance, cops catch you you're gone as well if they wanted to be really picky and have your bike examined at the pits. Wouldn't however void your warranty unless Yamaha can show the mods you have made are the cause of the claim. All in all though this bike is i believe the current bang for your buck champion followed by the even more mental mt 09/ fz 09. Anyways be safe people and live to ride.
are you Punjabi. on revzilla for Akrapovic full exhaust (yes full exhaust) lot of people are saying no need for power commander or flash. will fj09 pipe fit fz09. and do I need to do anything to ecu
I'm a dyno tuner, not a dyno operator the difference being I know what changes work and what little tweaks work or don't. A dyno operator simply does what the software tells him to do! Anyway I'm completely against flashing a ECU. Reasons being, one - no two bikes are the same, we have proved it with two bikes built one after the other and running exactly the same spec and almost the same miles, but when set up on the dyno we had two different maps one for each one, both making within 1-2HP difference. Two - ECU flashing is just hacking into a ECU, we know how much we hate hackers! When a ECU is just hacked the person doing the hacking just breaks into a small layer of the code and doesnt know the full extent of the code he is playing with. So a small tweak here to change the AFR value could also effect something somewhere else. We are seeing this time and time again and for example auto blip functions are added in a flash to a bike that doesnt have that function. Then the auto blip goes wrong and doesnt shut the bike down, instead it opens the gas and drives the bike and rider into the corner and disaster. We saw this at Laguna Seca earlier this year and at the NW200 with John McGuinness and various other riders in British Superbikes. A add on fuel module sure they can go wrong and break leaving you stranded but so can any part on your bike and its far more likely for something else to fail than a PCV.
To me, its a double feeling. On one side, leave ECU stock add PC... if PC fails just unplug and drive on. On the other hand, someone who truely knows the ECU to reprogram, he can optimise it better, throughout. Especially on older bikes where PC isnt able to do ignition. I honestly dont believe those accidents were caused bij de ECU giving throttle instead of shutting fuel down or whatever. If you have proof, please let me know, cause that really interests me
Simon, I reread your post and though I tend to agree for a big bit, the statement you made about the race accidents are completely faulty. Those guys dont just run a ECU flash. Those drive completely adjustable racin ECUs or the stock one gets tuned by someone with adequate gear and knowledge. Most often with backup from the factory....
What are your suggestion? I got CB650F with Ixil x55 full exhaust. Planing to change air filter. Question - whats better? Ecu flash, dyno tune, or leave it as it is?
I went with the ECU flash, why? Because it does things a power commander can't, It remapped my fuel like a power commander with pre settings, controls my timing, lifts the speed limiter, raises my rev limited by 500 rpm, also for my bike there is a safety feature in 2nd and 3rd gear wear throttle is controlled by the ecu and will not to go quite full bore, so that is restriction is removed. I do want to say once you flash your ecu the bike is for a road coarse only and is illegal to ride on the street, I don't know if I crashed the bike if they would check for this but I have been warned by a tuner here where I live, he would only do a power commander and would not touch my ecu. My bike is still in pieces but when I get it all together I will let you guys know how I feel about the ecu flash, my friend has the same bike I do and we are eager to race to see which one is better. I will say this, like Paul Davis said below, both is the best but if you have a choice of only doing one, the ecu flash is the way to go. Ya I plan on spanking my friends ass lol
Schnitz racing Gallardo, they are based out of Indiana, very quick turn around time and I am very pleased with the flash. Great company, highly recommended.
@@godofthunder67 you re right. I bought a used PC2 for me Srad, for think 80euro? But dynoing will kost around 240 prob... Now I read that there are 2 tuners in holland, that are epicly good in suzuki ECU tuning... for 150euro!!! So the PC2 goes out...
um, you can import maps from a power commander into the FTEcu software. I bought an FTEcu flash kit for my bike and I don't even have to take the ECU out to make changes. I also bought active tune which monitors air to fuel ratio and it makes corrections the fuel maps while you drive. You can also have it learn so it applies to changes to your base maps while still making changes as conditions around you change. If you are afraid of making changes to your maps then depending on the exhaust you get there are maps tuned for that exhaust. I have a Graves full titanium exhaust and loaded the Graves fuel maps and my active tune monitors and adjust while riding. A setup like isn't cheap. Graves and Yamaha go together and the quality of their parts are on par if not better than Akro exhaust, at least when it comes to putting them on a Yamaha. If you want cheap then go with a PC and a slip on from any one like Yoshi, M4, just stay away from anything from Two Brothers Racing.
I’ve had 3 power commanders, the cobra power pro works much better, it tunes to the fastest acceleration. They have no memory but ten minutes riding, and it’s dead on.
Dont bother with a 2nd fueler idea..Go direct with flash...There will be a small info delay with a secondary fueler..Flash allows a tuner do make huge changes over a fueler,which is now a possible added part to mess up....If you see alot of updates in oerformaces parts in bikes future,buy the kit which allows you to make your own maps for all conditions...Ex of one of the best kits to do all your own flashing is woolich raceing kit........Oh and with a secondary fuel deal like power commander,just changeing the fuel map doesnt mean it benifits your bike...Its a fuel map from joe blow who may live in another country with a dyno guy who did a poor mapping on a really dry or damp day,different altitude n such...So for me,i bought the entire flash/tune kit from woolich for my bike..
Dude you are talking bollocks. With a power commander you can add fuel to the 0% throttle column in the table to tune your engine braking. I did this on a dyno.
I don't get why in the US you are calling the MT series FZ... It doesn't make any sense since MT means "Master of Torque". Calling it FZ is getting rid of the bike's soul. About the flash/PCV, you should do both. 👍👍
Motos et Potos The FZ is still the FZ and the MT is still the MT. The difference between FZ and MT is that the MT has a little more power than the FZ. The reason they call the MT and FZ same bike is because they practically are with the exception of the amount of power they output.
“As announced at EICMA today, the MT-09 and MT-10 carry different names for 2018 but are otherwise the same as they were in ‘17. The MT-07, however, gets a few updates. Yamaha reworked the bodywork, mildly changing the look of the tank, tail, radiator shrouds, front fender, seat, and headlight. The headlight has a slightly pointier look similar to the previous FZ-09’s setup, and the seat now extends around the sides of the tank, adding 30 percent more area for riders to move around on. Overall, the makeover gives the MT a more aggressive, sportier look.” Link to quoted reference: www.cycleworld.com/2018-yamaha-mt-07-is-an-fz-07-with-euro-name-and-few-other-updates#page-2
If you want the best performance possible..BAZZAZ.. stores 2 Maps. + AFI To DYNOTUNE.. YOUR BIKE to the best it can run .. all the rest are street mods
good to know, i always engine break. my brake pads are like new after year of driving. rear brakes probably only touches few times cuz of dumb ass drivers in front. so im just gonna stick to pcv
i didnt like filming with your phone. it looks bad. i vote for the power commander because its better in every aspect but that depends on how deep your pocket is.
I have both, ecu flash and bazzaz. Initially thought to go one or the other. Then dyno tuner recommended both. More torque and responsiveness from combination. Smoother also, from eliminated restrictions. 05' ZX10R. Thanks for posting!
Great vid i have the ejk (for sale now lol) i decided to go with the ecu flash as i will be adding a ecu based quickshifter to the bike.
How do you get clear audio? No wind noise?
From what I have been told is that a ``custom`` ECU flash with the bike set up on the Dyno during installation is the best all round solution. This as opposed to mailing off an ECU for a standard flash for your bikes mods. Its a little bit more expensive, but it brings out the best in the bike. My 2008 R1 with three quarter exhaust and filter made 170.4 HP at the wheel and 82.58 lbs of torque. This was done on a notoriously stingy dyno and of course does not incl Ram air effect which is worth about another 8hp at speed. My previous R1 with similar exhaust set up and PC3 made 165.5hp and 79.5 lbs. Stock Euro bikes typically make 158-162 rwp and 76lbs . Biggest difference over stock was the much nicer spread of torque, general drivability and removal of Yamaha`s first and second gear 60% power restrictions in first and second gear. That was via the ECU flash. The PC 3 was great too, but of course can not alter any of the bikes electronic settings.
Better have a smooth running engine than jerky O/I behaviour which also takes it's toll from the other mechanisms. Clutch, chain, pinions engine internals... without mentioning the unsafe power delivery if you happen to come across a slippery part of the road while cutting throttle or opening up...
blah-blah-blah. I tried listening and fast-forwarding for 3 minutes and wasn't able to find the "meat": what is the difference.
LOL
Could you share a link to your gloves
I forgot the Lowe fan temp on the flash
Definitely flash. Especially the Ivan flash. Fuel tuners do just that and some can make minor timing changes. A good flash smoothness throttle, remove factory cutoffs, remaps your timing ALOT. And even let's you chang your fan temp controls. No question flash is always the answer
I picked the FTecu bike harness and just used power commander maps. Supper easy to install all you got to do is plug in 3 wired to the bike ECU harness and make sure you find a good 12.v ground for the ground wire. I like the engine breaking so I left that on but I lowered the temps at witch the fan runs at max to keep the bike nice and cool at stop lights on a hot day and its never been higher then 190.F since.
lower the fan temp is a bad idea, you want it ti run hot, just not too hot due to being too lean
stephenmwyatt2 why’s it a bad idea? I know it isn’t, but tell me why you think it is?
@@stephenmwyatt2 its a dumb idea, but wont harm the bike cause of the thermostats in the cooling system.
Do BOTH!!! SHUT OFF ALL THE BS RESTRICTIONS WITH THE ECU AND DO FUELING W THE POWERCOMMANDER
That's what I did and I love it
Most of these new ECU's can have their fuel maps adjusted just as well if not better than a powercommander. Some of the older bikes, it's piggyback or nothing.
Can’t you just do the ecu and tune appropriately without the fuel commander?
I would also recommend a Bazzaz set up. it plugs into all 8 fuel injectors where a power commander only manages the top 4 on the rail...
Ryan GoesFast bottom 4 my dude. not top
It’s my understanding that who ever is doing the flash has control over all those aspects. All I am saying is they can tune in or out your desired engine braking, idle rpm and rev limit
Before I got my FZ-09 I had a 07 just like yours. M4 slip on exhaust with a fair amount of popping. Got my ECU flashed, worth it. Butter Baby...Butter👌🏼😉
How is the Mpg on the 09 with the flash?
Sounds like you need to adjust TPS throttle positioning sensor before anything else,otherwise you're not addressing the issue only masking it .
It is a 2 step process. Do the base ECU flash to remove restrictions and then install the power commander or auto tuning kit to maintain better AF ratio. Not sure why this is so hard to understand.
That's what I'm gonna do.
Because people always look for the cheapest option possible. Paying for a ÉCU flash and installing a stage one kit is considered expensive to most. Maybe they should find another hobby ?
Power commanders are known to fail then you gotta pay another $400
That is next level dumb. You can get a flash package like Woolwich racing that has auto tuning and data logging built in. You can flash the bike with the ecu installed. Piggy back systems like PCV are garbage old technology.
Ian McDonald wire words brother. So on a 2015 Honda cbr1000rr like mine.. I can get away with just the ECU flash and skip the power commander?
Good job
Which will give you more top end? And what can you recommend to us?
Ecu or Power commander?
A note on your camera setup ..... I have seen a couple of videos where the ram X mount has "let go" of devices held in that orientation. It has to do with when / if you hit a rut in the road, the weight of the device pushes against the lower jaws which opens them. Perhaps add a case and tether for security? Just trying to help you keep hold of your shiny new Iphone 7Plus :-)
I had a Guhl Motors flash done on my ZX-14R, and the power increase was immense. The Fuel Commander can fail, and leave you stranded out of town, the flash is as reliable as the stock ECU. My bike was slow until I had the flash done. Good value!
busaking1 hawley was it pretty expensive to flash your bike?
KN, it was $375 at Guhl Motors, and worth every penny. Don Guhl is reflashing it for right now at no extra expense because I regeared to a 16 tooth ft. sprocket, this threw the traction control off. Ride safe.
busaking1 hawley sweet! thanks man!
I do agree with you ECU is more reliable.
But if your PC ever fails you can unplug it and reconnect the original connectors (bypassing the PC, just like the stock configuration). It wont fix the PC but at least you wont get stranded
@@ZPdrumer appearently 97% of PC owners just doesnt have a clue what they bought, what it does, etc...
One question ...If I bought the ecu flashing kit will I be able to download the software for free or that also need to be bought
Harley Davidson will flash your ecu for free
Yes, you can download the map that matches your setup from PC's website
Nice topic!! I've been debating on whether or not to get my ecu flashed on my s1k. Subbed!
+DaWrathOfGod Thanks for the support!
so how the EJK unit fits in here? anyone could explain? thanks..
+sobering cat Basically pcv
Doesn't seem like your in ca but I know removing the evap and air injection helps stop so much engine braking and no more popping i have a 15 fz09 and it was twitchy with ard engine braking the bike came flashed and I have a power commander its so smooth and I still have to dyno it
will installing a power commander or ecu flash remove the anti theft on my bike?
No
Got rid of both and bought a stand alone ecu, should've done this all along.
Can you use both? I have a PC5 but i wanna flash my ninja 400. Is that a thing?
Yes You can flash to derestrict, makeotheradjustments, etc depending on which flash and what's available four your specific bike. Then you could just use pcv for af tuning.
Get a 600 problem solved
An even better option is to do both!. Check out the Flash tune on Revzilla. Really easy to install and you get the best of both worlds. There is also an auto tuner you can get with it that will tune based on current conditions.
+Paul Davis Yeah I would loveee to have both!! Along with auto tune!
Here is a link. ftecu.com/shop/2015-yamaha-fz7-data-link-ecu-flashing-kits/ I got mine after watching a video about it by Jake the garden snake. No sending the ECU out to be flashed and no insane rewiring to do. It covers everything you are talking about with 4 connections into the wiring harness of the ECU.
Both works for me. Bazzaz offers their version of auto tuner. On my to do list.
I need a Honda CBR f4i 600/2004 model ECU
Paul Davis zpsszwpz
Power commander just makes it easier and faster for the tuner to tune on the dyno
A few things you said were a little bit off. You don't have to remove your ECU to flash it. You can do it at home with your ECU still in the bike. All sorts of programs are available depending on your equipment. A lot of them are available from places like FTECU.com. You can also have a professional custom flash your bike. The same is true for a Power Commander. On newer bikes you can adjust all sorts of settings within the ECU. It doesn't automatically cut off your engine breaking. That's up to the owner of the bike. A PC and ECU working together is actually the way to go for high performance.
Which is better for a 2019 Yamaha MT10 PC or ECU flash?
Flash! You can also get a better results that way. Especially if you can out your bike on the dyno instead of shipping the ecu to be flashed
What if you get a pc and an ecu flash?
That's what I did....simply the best
Is it possible to do both?
I think that's what someone is saying reflash all the restrictions and use a pcv to tune air flow . I think I'm correct but hell what do i know I'm on here myself trying to figure it out and can't make head nor tail of it .it sounds to me like it boils down to people's opinions yet again like everything else in this fucking post . All the best .
The choices are very similar but you forgot to mention the added cost of a Power Commander v.s the already installed ECU. A Power Commander costs $360 and requires installation. A FTLink costs ~$50 but I can't find one for my motorcycle. For ease of modification, I'd opt for a dino verified ECU flash.
Is this like hacking your bike's software, and kind of dangerous to do? I hack phone software all the time but at least no one is gonna get into an accident when they use my flashed phone.
If the manufacturers didn’t restrict the performance from the factory they wouldn’t need to do this , unfortunately environmental bs and liability concerns prevailed
true.
Can I choose neither and keep the bike running lean with backfire downshifting or will it eventually mess up my engine and (burn my piston rings) and what not
F
I say Ecu. and if you go to the ftecu get the bench kit. it's way better. this comes from a guy who got the bike side. I was 100% confident i can do that. well I was wrong
Stupid laws over in Australia state that for Restricted Open riders, we cannot exceed 150kw per ton power to weight ratio... and the MT 07 is already a bees dick off being over that. So having a tune could void my warranty and insurance if I have a crash. The only way to prevent that is to go onto an Open license, which requires another $300 riding course.
+DA2THFA1RY Boooooo
No wonder there are so many drug addicts in Australia. Country sounds worse then China/Russia
Or another of looking at it is they would rather a 17 year old with no experience not go out and jump on an R1 and kill himself in not time due to crazy power to weight with no skills, truly a recipe for disaster. A year is a reasonable amount of time to gain some road craft before riding a weapon.
It is a lot better than before when there was 250cc limit. Kids went out and bought RGV's , RZ's and KR1's which while being fantastic bikes, they were also not good bikes to start on due to the power delivery of these bikes. It's now more about linear power that is easier to control so you can buy up to 660cc with power to weight of 150kw per ton or less.
As far as the MT 07/FZ 07 is concerned there are 2 versions, a restricted and a high output model. The restricted version is sleeved to reduce capacity from 689 to 655cc. On the street there is not a lot of difference as while the high output version has around 78 rwhp and the restricted version has I believe around 42 rwhp the restricted version is pretty close in torque output and that torque is tuned to come in lower on the restricted so in effect it's not really slower at normal speeds, will be noticeable at higher revs however.
The restrictions are throttle via a dog leg section on the throttle body which restricts the travel, this can be easily replaced. A airbox restriction which reduces air intake, this can be dremeled out and 5th and 6th gear are limited to i believe around 6000 rpm in the ECU so a flash is required to remove.
DA2THFA1RY - As well as getting an open class license you would also need to re register the bike as non Lams and once this is done it can never been downgraded back which will affect resale of the vehicle given the market is a lot bigger for LAMS approved bikes, also as you state no insurance, cops catch you you're gone as well if they wanted to be really picky and have your bike examined at the pits. Wouldn't however void your warranty unless Yamaha can show the mods you have made are the cause of the claim.
All in all though this bike is i believe the current bang for your buck champion followed by the even more mental mt 09/ fz 09. Anyways be safe people and live to ride.
are you Punjabi.
on revzilla for Akrapovic full exhaust (yes full exhaust) lot of people are saying no need for power commander or flash.
will fj09 pipe fit fz09. and do I need to do anything to ecu
I'm a dyno tuner, not a dyno operator the difference being I know what changes work and what little tweaks work or don't. A dyno operator simply does what the software tells him to do! Anyway I'm completely against flashing a ECU. Reasons being, one - no two bikes are the same, we have proved it with two bikes built one after the other and running exactly the same spec and almost the same miles, but when set up on the dyno we had two different maps one for each one, both making within 1-2HP difference. Two - ECU flashing is just hacking into a ECU, we know how much we hate hackers! When a ECU is just hacked the person doing the hacking just breaks into a small layer of the code and doesnt know the full extent of the code he is playing with. So a small tweak here to change the AFR value could also effect something somewhere else. We are seeing this time and time again and for example auto blip functions are added in a flash to a bike that doesnt have that function. Then the auto blip goes wrong and doesnt shut the bike down, instead it opens the gas and drives the bike and rider into the corner and disaster. We saw this at Laguna Seca earlier this year and at the NW200 with John McGuinness and various other riders in British Superbikes. A add on fuel module sure they can go wrong and break leaving you stranded but so can any part on your bike and its far more likely for something else to fail than a PCV.
how about woolich racing ecu ? that is really good for my bike
So a Schnitz Dragracing flash with fuel tables is bullshit?
To me, its a double feeling. On one side, leave ECU stock add PC... if PC fails just unplug and drive on.
On the other hand, someone who truely knows the ECU to reprogram, he can optimise it better, throughout. Especially on older bikes where PC isnt able to do ignition.
I honestly dont believe those accidents were caused bij de ECU giving throttle instead of shutting fuel down or whatever.
If you have proof, please let me know, cause that really interests me
Simon, I reread your post and though I tend to agree for a big bit, the statement you made about the race accidents are completely faulty. Those guys dont just run a ECU flash. Those drive completely adjustable racin ECUs or the stock one gets tuned by someone with adequate gear and knowledge. Most often with backup from the factory....
What are your suggestion?
I got CB650F with Ixil x55 full exhaust. Planing to change air filter.
Question - whats better? Ecu flash, dyno tune, or leave it as it is?
Do both. Flash for general not specific
Can u put both
Yes you can. ECU flash to remove the restrictions and PCV for a custom maps
@@BrapModeOn thanks for the instantaneous response ♥️
I'll listen to the comment below, i dont wanna break down with the PC
I went with the ECU flash, why? Because it does things a power commander can't, It remapped my fuel like a power commander with pre settings, controls my timing, lifts the speed limiter, raises my rev limited by 500 rpm, also for my bike there is a safety feature in 2nd and 3rd gear wear throttle is controlled by the ecu and will not to go quite full bore, so that is restriction is removed. I do want to say once you flash your ecu the bike is for a road coarse only and is illegal to ride on the street, I don't know if I crashed the bike if they would check for this but I have been warned by a tuner here where I live, he would only do a power commander and would not touch my ecu. My bike is still in pieces but when I get it all together I will let you guys know how I feel about the ecu flash, my friend has the same bike I do and we are eager to race to see which one is better. I will say this, like Paul Davis said below, both is the best but if you have a choice of only doing one, the ecu flash is the way to go. Ya I plan on spanking my friends ass lol
Oh and one more thing, a power commander is 300 bucks for my bike plus another 300 for the dyno tune, my ecu flash was only 200 bucks.
Dj Zielinski where did you get it flash at? I got a 07 750 gsxr
Schnitz racing Gallardo, they are based out of Indiana, very quick turn around time and I am very pleased with the flash. Great company, highly recommended.
@@godofthunder67 you re right. I bought a used PC2 for me Srad, for think 80euro? But dynoing will kost around 240 prob...
Now I read that there are 2 tuners in holland, that are epicly good in suzuki ECU tuning... for 150euro!!!
So the PC2 goes out...
@@godofthunder67 Cheap Ass!
um, you can import maps from a power commander into the FTEcu software. I bought an FTEcu flash kit for my bike and I don't even have to take the ECU out to make changes. I also bought active tune which monitors air to fuel ratio and it makes corrections the fuel maps while you drive. You can also have it learn so it applies to changes to your base maps while still making changes as conditions around you change. If you are afraid of making changes to your maps then depending on the exhaust you get there are maps tuned for that exhaust. I have a Graves full titanium exhaust and loaded the Graves fuel maps and my active tune monitors and adjust while riding. A setup like isn't cheap. Graves and Yamaha go together and the quality of their parts are on par if not better than Akro exhaust, at least when it comes to putting them on a Yamaha. If you want cheap then go with a PC and a slip on from any one like Yoshi, M4, just stay away from anything from Two Brothers Racing.
I’ve had 3 power commanders, the cobra power pro works much better, it tunes to the fastest acceleration. They have no memory but ten minutes riding, and it’s dead on.
Carnegie PA?
Yup :)
Dont bother with a 2nd fueler idea..Go direct with flash...There will be a small info delay with a secondary fueler..Flash allows a tuner do make huge changes over a fueler,which is now a possible added part to mess up....If you see alot of updates in oerformaces parts in bikes future,buy the kit which allows you to make your own maps for all conditions...Ex of one of the best kits to do all your own flashing is woolich raceing kit........Oh and with a secondary fuel deal like power commander,just changeing the fuel map doesnt mean it benifits your bike...Its a fuel map from joe blow who may live in another country with a dyno guy who did a poor mapping on a really dry or damp day,different altitude n such...So for me,i bought the entire flash/tune kit from woolich for my bike..
just flash it know and feel the power
Dude you are talking bollocks. With a power commander you can add fuel to the 0% throttle column in the table to tune your engine braking. I did this on a dyno.
I learned nothing. Thanx
Jose Moreno then you're fucking stupid cuz i actually understood the difference cuz of it
Lol.
yes the phone is nice
I don't get why in the US you are calling the MT series FZ... It doesn't make any sense since MT means "Master of Torque". Calling it FZ is getting rid of the bike's soul. About the flash/PCV, you should do both. 👍👍
+americadanyus Lmao!! I likr that!
Yamaha decided for you and now FZ is called MT, even in the US.
Motos et Potos The FZ is still the FZ and the MT is still the MT. The difference between FZ and MT is that the MT has a little more power than the FZ. The reason they call the MT and FZ same bike is because they practically are with the exception of the amount of power they output.
“As announced at EICMA today, the MT-09 and MT-10 carry different names for 2018 but are otherwise the same as they were in ‘17. The MT-07, however, gets a few updates. Yamaha reworked the bodywork, mildly changing the look of the tank, tail, radiator shrouds, front fender, seat, and headlight. The headlight has a slightly pointier look similar to the previous FZ-09’s setup, and the seat now extends around the sides of the tank, adding 30 percent more area for riders to move around on. Overall, the makeover gives the MT a more aggressive, sportier look.”
Link to quoted reference:
www.cycleworld.com/2018-yamaha-mt-07-is-an-fz-07-with-euro-name-and-few-other-updates#page-2
U didn’t even put video
Engine breaking is bullshit and it makes the bike jerky, and makes the bike so much better
If you want the best performance possible..BAZZAZ.. stores 2 Maps. + AFI To DYNOTUNE.. YOUR BIKE to the best it can run .. all the rest are street mods
I agree, plus the Bazzaz uses all 8 injectors on liter-bikes out if the box. PC requires secondary module.
good to know, i always engine break. my brake pads are like new after year of driving. rear brakes probably only touches few times cuz of dumb ass drivers in front. so im just gonna stick to pcv
Or you can buy a woolich racing kit and flash it yourself...
Dude nobody changes exhaust often. Exhaust changong is expensive and nobody swaps them out like u said
jeremybly lol I’ve had 5 exhausts for my bike in less than a year, Dan Moto, Toce, akrapovic, and 2 different M4s
@@brandonjones5787 than you ve got too much money...
Wrong! Most people do!
Cool video, absolutely wrong with the information but ok....
Why do you keep calling it a fuel commander? It's called Power Commander.
8701michael because it works with the fuel and timing dumb ass
8701michael same thing
Does it really matter?? Small potatoes Buck.
i didnt like filming with your phone. it looks bad. i vote for the power commander because its better in every aspect but that depends on how deep your pocket is.
+Qais Alehremi I already recorded some videos like that :(
I can hardly hear this guy so muffeld up at his engine noise
Knows nothing about tuning motorcycles or cars.
Tries to tell people about tuning.
I agree - i had pretty basic knowledge back then and should not have tried explaining it.
waste of time watching this
Thanks for the feedback! Working on improving content.