วีดีโอ

no ai music PLEASE

this video is pointless lol

It's crazy the default uses the cloud for a local device...

I'm here just for the really really cool! colors

i am watching this like i can afford anything more that amazon basic pla

Is this AI generated music? 😃 Which tool did you use to create it?

what glue did you use?

Wow.... thank you for the shout outs. I'm humbled to help out in any way I can. One note about the Inner/Outer/Inner wall ordering - I don't think it comes into play when you use vase mode with 1 continuous wall. If I gave you the impression that it does then I apologize. In my limited experience I see it really come into play when you have 3 or more walls. With 3 walls where you have Outer | Middle-Inner | Inner-Inner, Bambu Studio first prints Inner-Inner wall which is good because if there is any excess build up in the filament it gets deposited where you will never see it. Then the Outer wall is printed (which leaves a gap for the Middle-Inner) which helps ensure uniform outer wall layer lines as it is not being pushed/bulged out. Then finally the Middle-Inner is printed which fills in the gap between the two. Interestingly if you have 2 walls, Inner/Outer/Inner does the Outer wall first and then the Inner wall, which is the opposite of the default of Inner/Outer which does Inner and then Outer walls. Again sorry if I misled you on what that wall ordering does on a vase mode, but again thank you for the shout outs. 🙂

Oh no another filament to buy lol, thanks for the review.

Have to say the finish on the base using that star plate is amazing. Very nice.

Hey Len, is there any chance you could help me tune ninjatek chinchilla filament for the x1c? Right now it's a 50% fail rate and just stops extruding. I flush it with a bit of 95a tpu and it's good to go again. And have a bit of stringing. Other than that the surfaces are nice and smooth good quality. Thank you in advance if you or any other members could help me to figure these issues out.

I’ve been wanting to try this filament! Thanks for this vid can’t wait to watch!!!

Do they wear down?

Your theory on the aluminum sides holding more heat does not make sense in a physics sense. Aluminum is one of the best conductive materials we have. As such it will dissipate heat way faster than plastic. This is why heatsinks are made of aluminum. The X1C probably has different bed heaters than the lower cost p1p / p1s. From my research the differences in the X1C over the P1S are Lidar, door sensor, hardened extruder and nozzles, Control interface (color touch vs basic display), and I just learned from your video the bed heaters. That said the p1s can still print fiber filament IF you upgrade the extruder and nozzle to hardened steel. Though the lower temp bed may make the prints more difficult. Thank you for the video.

I would think that you can't sand them up to make them even smoother, as the effect is imprinted, right? I would love to see a very smooth surface, but I guess its the nature of the prints.

I just bought these as well, i know they're a trend, but man I keep finding really great spots to use them in. The one thing I can't find though, is a STARs one that only has the small dots but NOT the big stars on it. that would look so cool

I don't even use bamboo studio. Unless I'm doing something for someone else I find bamboo studio a piece of crap. I use a derivation of cura for slicing. Then I put the modified G-Code on a card and run it from there. The camera is useless. The firmware is crap. You get your acceleration and deceleration of the hot end from the code generated from bamboo studio unlike klipper which modifies the code on the fly. The only thing I really do appreciate is the electrical connectors. They sometimes flake out and give you erroneous codes but unlike the k-max they're pretty sturdy and not going to fall apart after connecting them a few times.

There was no High Temperature Plate in our X1 - Carbon package. Also, that plate cannot be delivered currently by Bambu Lab. Their website lists the Engineering Plate as an alternative for 100°C printing. Is that a good choice, too? That one we have.

Sir, the other side of that plate with star holo is not holographic, it's a regular gold PEI plate like in Bambu and not supposed toale holo effect

Maaaaaan. You are too cool for taking the time to lay this down

Subscribed. Rad vid

Great video, I can't say enough good things about this one. Your way of explaining things is very easy to follow even for us that may not be so good at this. Thank you for the video and for the links to the products as well.

Can I use WS281 Addressable COB lights? Please show a wire IG diagram. Ie how to actually connect to printer? Lastly, most of us would Not rather connect to HA, just be independent. Can that be done ir through Alexa? 18:01

Wow this is way too complicated for me. Maybe bamboo lab could just have all this crap in a simple program that would identify your machines and your operating system that you want to look at the camera. And Wawa you have s*** your worthy paid for on your system. F*** you bamboo lab.

Do you need to use the app in order to add the printer initially?

Aux fan on or off for ludacris?

Thank you so much. The configuration update was why I was here. I couldn't figure out why I kept getting an error for ABS-GF and that was the cure!

16:50 its warping like crazy! That's even worse than any ABS I have used thus far. Just saying that your print 'came out well' is silly to be honest, I would consider that a hard fail.

One of the keys to ABS not warping is preheating your enclosure for longer. I Turn my bed on @ 100 C for 10-15 min before I send the print job.

I’m new to this process. Maybe I missed something but wouldn’t it dissolve with hot tap water? I’m guessing you would still need to replace it with hot water every hour.

AVOID AVOID AVOID at all costs, Bambu f'ng Labs is the worst company I have ever dealt with.

I laughed out loud when you said "That's stupid!" about BL not having the filaments loaded in there. That was awesome and I agree with you. I have to admit I didn't know the thing about pressing the numbers on your keyboard. That's so obvious now that you pointed it out, so thank you for that.

Looks like that last print warped. Add 5 to 10 degrees more bed temp

Sorry to bother, but I enjoy ABS as well, just curious do you use anything special for supports? I know that there is a specific support material for PLA, but is there one that you have found for ABS/ASA? Thank you for your time and your AWESOME videos!!! I just ordered some ABS-GF!!

Damn there was no comment on the warping which was abit intense. I love your content but you need to be abit more critical and point some flaws. Maybe comparisons etc but Iove your content

Yes, make more songs 😂👍, i love it !!

Pretty bad warping. Mouse ears wouldn't help?

LOL bonus likes are deserved for that song!

Lmao, did you make that song? Is that you singing? That is awesome, I love it!!!

I have had good luck printing the PVA as just the interface layer. then not bothering dissolving. just let it come off easy. Just make sure to set the gap to zero. keeps the surface finish good. depending on the main part material defines the best support. One thing to consider is swapping filament takes time, and poops

I have a question. On my a1 mini it has the bed temperature at 65°C for their filament but on the bambu wiki it shows pla should have a bed temperature of 35-45°C and so do other filament brands. Does the bambu just run a hotter bed or is the pla they make need to be printed at that temperature? I’m confused

A question. My PC ( Windows 10 ) is connected tot the web by LAN. How to make if I go for the connection PC - Bambu Lab X1 Carbon, over WIFI but keep on the PC / WEB over the LAN ( cabled ) connection? Reaaly in a mood here should I drop my Bambu Lab to the scrapyard or keep ik anyway.

What speeds did You use? Generic, or did You changes any? Seem to be quite too fast :O

be aware that the stl's for the light guide and frame from bambu dont fit together.

I swear by AquaNet...so cheap and works so well, but I have the Sliceworx Flex Dipped plates that everything stick too with out needing any adhesive at all

Interesting video. Why did you don’t use orca slicer? Spécial reason?

Great video Thank you.

There was a filament update available for Bambu Studio 1.8.4.51 this morning that added the PA-GF, ABS-GF, plus a few more new filaments.

Ah man i missed it..

I liked the Bambu Studio until I saw Orca Slicer's measuring tool. Game changer if you're someone who resizes things and want to check sizes.