วีดีโอ

Thank you, I agree 👍

Pretty sure your looking for the red 1995 panels. Use this Google search: 1995 400ss red door panels coverlay Find the cheapest seller closest to you. Good luck with your project 👍

I have updated the link Thank you 👍

I used vinyl and fabric spray paint to go from grey to black. Looks better black, in my opinion. A year later, I swapped out the original seats for new ones with lumbar support and better cushions. There are links in the description of each video for anything I used in a video 👍

As long as you start in park, when installing a new switch like I did on the side of the 4l60 the switch is in park too. Then each gear is picked up by the switch as you pull back the shifter. 👍

@@thisoldhooptie That cant be the case because the other connector you didnt add is the range switch section. I know because right now Im doing a 4l80e swap and Found out this transmission wont do anything cept reverse and 2nd gear default without the range feed connector wired up.

@@thisoldhooptie if you dont have the range switch, At the very least you have to wire a on/off switch on the dash to turn on for D4 when you shift into Drive on the column. To be fair I could be running into some confusion because Im using a 2000 3500 van computer and cant for the life of me figure out where to supply a tach signal to from the HEI old school distributor (one of the wires for the cam or crank sensor, no idea because no information out there). Im finding the sloppy or flat out wrong information put out there by people to be pointless. I dont understand why some put out fake or incomplete information.

I'm not a mechanic, I can only give you my experience with this truck as it was my first ls swap. When I had the original wire harness, which did have all the transmission plugs, every thing worked fine when I drove it around the block after fixing wire issues. Then I swapped to a cheap Amazon ls swap harness, which only had the one plug for the switch, and that drove fine, swapping the gears as I test drove it. I would have noticed if it was stuck in 2nd gear. I have since pulled it apart to fix the body issues. The engine and trans are out right now. What I can do is go over it when I put it all back together later this year. I followed info from this site to deal with wire issues when I was stuck. Definitely easist yo use the common swap parts and wires if possible. 👍 www.lt1swap.com/

My guess is the large round connector on the 4l60 passenger side has what it needs to allow computer control.

Thank you 😁 good luck with your project 👍

No, not yet. I'm waiting too. I need one for my tahoe.

Get the fix it's totally worth the 100 dollars. 👍

Yes, I would buy it again. It is very easy to pull apart and clean when the kids spill things on it. Also, the warranty is solid when a piece broke last year. The part was shipped fast, and the repair took a few minutes diy. As for the deep choice, yes, I would take the deeper one if you and whoever uses it are tall. When putting our feet up on the ottomans for movies, it would be nice for the seat to be deeper. It would also be nice to be able to put throw pillows down with more space.

Thank you. I went up to 320 or 400 with the black. It's in the prep. If you get things smooth, it will look great. It also depends on what you're painting with. If you're using rattle cans, you may want a finer grit so the paint can easily hide the sanding marks. As long as you use thin enough coats and the prep is right, it will stick with 600, too. I just didn't feel the need, and it came out fine, in my opinion. Good luck with your project 👍

Thank you 👍

Will do 👍

It's over 100 degrees with crazy humidity where I'm at. Closing the door is not an option most days in Florida. One day I'll install an ac then I'm good to go. About the light, it has been great for when the hood is up blocking the lights or for in the cab work. 👍

We have a pretty big family that has used and abused the couch for a while now. It is nice to be able to lift the bottom cushion and the panel under it to get things the little ones have dropped. I would estimate that maybe 3 times things have passed the cushions. Coins, a comb, and little toys. The pillows are thick and hold shape. The remote doesn't fit in the gaps, cell phones do not either. Not much has squeezed past. The ottomans that are full of stuff are heavy and don't slide forward. The empty one slides all the time, and phones slip between the couch and that ottoman.

@@thisoldhooptie Access with a vacuum might be the plus side. I am looking at the chair and a half.

@cynvision One thing a few people have commented on is that there is a deeper version. If you are tall or want to use throw pillows, I would give that deeper version a try. While I am still happy with what I have, the one thing I would have liked if available when i purchased is a little more depth to the chair.

@@thisoldhooptie I am sure I would enjoy that. I am very used to sitting on a CordaRoys bean bag. The wide chair was my favorite at my parent's home.

Thank you 👍

No problem 😁 👍

Sounds like a great place to work. I will have a look at the dehumidifier you listed. Thanks for the info 👍

@@thisoldhooptie just looked up,mine is discontinued the replacement is E100. You can install a condensate pump and water your garden.

That's in the works. It's 100 degrees in my garage sometimes. Super hot 🔥

They have been welded closed. I open them with a remote like an alarm. If you want to see how that's done in my truck playlist a few months back, I started another truck cleanup.

@@thisoldhooptie that is pretty cool I try it on my 96 suburban

The dash will fit its a lot of work. The stuff behind like ac and wiring, also the doors are all not going to line up and play nice. If you have a full doner truck, it can be done 👍

I wish it was deeper. That would make it perfect. Yes, we still use it every day. I have washed the fabric after the kids spill on it. I also tested the warranty, which was great. Im still a happy customer. 👍

Thank you. It has been a blast learning and trying things out. As you will find out in the next video on this truck,I ended up going all black for a bit to give me more time to practice with flake and perl. You should have no problem with a single color. I will be testing what I have learned later this year with orange perl over white on the s10. The now black truck is doing great more to come when time permits. Family first always! Good luck with your truck 👍

Definitely standard. That's the one flaw. Still enjoy them daily. We have the extra long ottomans, which even things out.

Thank you. Yes, the seat belts I used come in a full set as you see in the video. Everything was in the box. They have held up well, great buy! For the billet dash pieces, go to cunninghammachine.com look through their obs section. Good luck with your project 👍

@@thisoldhooptie appreciate the feedback brotha! And will do haha slowly but surely #billettheworld

Thanks, bro! Good luck with your build 👍

Hello, is there a way to contact you?

@@Mohammed-uz1sn You just did. What's up?

@@thisoldhooptie Hello my friend, thank you for your response. I wanted to ask you about I want rear axle bearing seals for a 1988 Chevy C1500 truck. Can I get those parts from Amazon?

@Mohammed-uz1sn Yes, you definitely can get them from Amazon. I highly recommend getting them from a local auto parts store if you're not familiar with what you are buying. If this is your first try, bring one into the local parts store to compare with what you get. This may save you a trip home and back if there is a mix-up.

The turbo can and standard are not interchangeable. The white tip under the cap is much larger on the turbo cans to feed the big cap. I will pop the cap off the first empty can when I spray the cab and let you know in the video if they can be swapped to the standard cans. My guess is no, let's find out 👍

@@thisoldhooptie that would be awesome. The color I'm going to be using doesn't seem to come in quarts. It would be worth it to buy one of the turbo cans just to get the better nozzle. From off the grid in Az.

Another good option is to decanter the spray can with the color you like. You poke a hole or shoot it out a straw into a container until you have enough to spray from your gun. That's going to give the best finish. That also takes the most work. Either way should turn out sweet 😁

@@thisoldhooptie yes, I just saw that on another channel today. He just sprayed it right into the paint cup. And sprayed it. Which would be ok, because it's already thinned, no guessing. Right on.

That's the plan 👍 😎

Thank you 😁. How's your truck doing?

@@thisoldhooptie rear end blew up . 9 " . I have new locker with 8 "

It happens. Keep on trucking 👍 😎

I have never tried to pull them all the way out. They like the original lock when pulled fast. I use my daughters booster with the seat belts. They work properly.

@@thisoldhooptie thanks man

Thank you, I think 🤔 🤣👍

😁👍

Thank you 👍 No, I still need to finish the paint job on the obs. I also have a full air suspension setup for that truck. I will be bringing that back in the garage this year now that I can winch the s10 in and out.

@thisoldhooptie sweet. I am also building an obs that i currently have a 5/7 drop on and will eventually bag

Thank you 👍 I will definitely do that. I ended up going back to black for a bit due to not being able to match the panels. I'm about to start a rustolium playlist. Stay tuned. This group of videos will answer all the questions. As for your questions, no, the clear was crystal clear, even better when cut and buffed out. The only clear that I have used that went on cloudy and then cleared was the 1k stuff on the dash. I'm not happy with the 1k. It's not as hard and shinny as the 2k. It's clear and looks great as cam be seen in many of my videos. I just prefer the 2k for all its benefits. The black other then being dirty has held up great so far. The dash has too. I'm also a big fan of the rustoleum paint jobs 😁

@@thisoldhooptie thanks for your response ,im thinking of doing the same thing to my obs stepside. but with pearl .i live in west Texas where the sunshine and uv rays are brutal .keep up the good work ,happy trails .

There is a video for each in my truck playlist. The description of each video has links and product info of everything I used in that video. Quick and dirty, dash lmc truck, seats seats4trucks.com, door panels are from Google search for coverlay door panel your truck make and year. Good luck with your build 👍

Nice! Even though it's tiny, this thing is the best mod for these suv. Having to hit that button drove me crazy.

Thanks, bro :) Did you get any wrench time in this weekend?

@@thisoldhooptie Unfortunately I did not. In between getting things done around the house and creating content I have to still work around the house and honey-do’s. . I travel for my job and work gets in the way. LOL. I always like what you are doing so keep them videos coming bro!

In the middle of what?

They are listed in the description under the corner lights. I would definitely check that the seal is good on the headlights. If not, grab a tube of clear silcone and seal the whole front piece. I have not had moisture issues. Others have and mentioned that to me. Good luck with your project 👍

It will very much depend on what you plan to keep and what you plan to add. The best place to start is here lt1swap.com/wiringharness.htm

I'm glad it helped 👍

The plastics and dash and back carpet still look great today. The floor needed a touch-up under the peddle area from sneakers scuffing the area up over time. The smell went away fast for me, a few days. I got rid of the seats and got new ones shortly after this video. I can't say how long the bench seat lasted. If i did things again. I would still do all the plastics, dash, and the back carpet. I would order a new floor carpet and get a black seat cover. Good luck 👍

Thank you 😁 1. Yes 2. Yes, all can be removed and washed. I have little ones that spill over all the time. :) 3. The issue I had was fixed in production they sent me both end tops, so the other side was stronger, too. My 180-pound nephew sat on the top, and it cracked. He has sat on the new tops, which have held up since. The warranty comes with it free. Other then the size that was a big factor in my purchase. We have broke a few couches from the kids jumping on them. I wanted to be able to fix them at home instead of paying a fortune sending it out or getting expensive warranties from local stores. 4. The return policy should be somewhere on the website link is in my description of the videos for this couch. I highly recommend getting one chair piece to test prior to buying. I know that is returnable. That's what I did to be sure it would work for us. It's not a deep couch but was perfect size wise where others were not. It has held up well. Other then the top issue which new versions do not have, it's held up great.

@@thisoldhooptie thanks so much for your help!

Nice 👍

Which bolt are you referring too?

I'm glad it helped. 😁 Thanks for taking the time to leave a comment 👍

Check my playlist for the door panel video. It's a couple years back. The details are in the description of that video. They are coverlay and are doing great, very happy with them 👍

Thanks, I need to make an epoxie top for that at some point this year. My little girl loves it, too. After the top tore, I promised to fix it this year. But until then, it's the perfect height for body work on this low truck 🤣

Thank you 👍

Thank you, 👍