Just wanted to point out that you should NEVER use brake cleaner (or any chlorinated solvent) prior to welding. Welding causes the brake cleaner to decompose into phosgene gas which is extremely toxic and can kill you.
@@jacobegnor4197 The wheelchair broke while he was near a stove and he knocked himself out turning the gas on. This caused his his entire apartment complex and every nearby building to burn down, killing over 9000 people. It was quite a tragedy.
JB Weld is actually a very good adhesive, with great tensile strength. My ME engineer buddy tested some lap shears, using this epoxy, and it had very similar results to adhesives used in the composites industry, but at a fraction of the cost.
Mr.Mister I work industrial maintenance and I'm not positive about this application but I've seen plenty of proof for me to always give it a full set time. Like concrete. Definitely not strong after 12 hours max they only waited one night then tried to break it hahaha.
I have made some pretty insane things out of JB weld, you are 100% right it is all about the cure time. I don't know if two or three packages of JB weld would be enough even fully cured... Kind of makes me want to try before I swap in my new rear gears and locker :)
You should have packed it with JB Weld! Like basically fill it to the case with JB weld so the gears are bricked together! I honestly think if it was completely full it might work
Welding after spraying it on a surface to clean it won't do a damn thing, it evaporates. However, I had a coworker who sprayed a bunch of chlorinated brake cleaner through a Honda gx390 engine and it bogged down and came out as black smoke that burned his lungs and his exhaled breath was white fog for some reason lol Funniest thing I ever saw.
Just for a warning! Cleaning parts that will be welded with brake parts cleaner is NOT safe. When you weld a part that has been cleaned with brake parts cleaner it creates toxic fumes.
You are wrong, Brake cleaner is designed to evaporate very fast, you have never used any parts or brake cleaner have you? I fix motorcycles for a living .
Yes, on a flat, polished and clean surface brake cleaner evaporates quickly, on material with deep pits or crevices it can remain. I don't know if you weld, but it's a real hazard if you arc weld with a gas shiled. This is a well published phenomenon to the point where practical welding was breifly introduced during my freshman yeae of engineering we all had to sign to say we had listend to the safety warnings, been given a written copy and read it. Modern brake cleaner is less likely to be chlorinated, but if you happen to use a chlorocarbon to prep before arc welding with a gas shiled there's a very real risk of phosgene.
Uncle Quack really? You fix motorcycles for a living? That means you change parts in and out? How much welding do you really do? I bet it’s squat in comparison to me. I’m a welder for a living! I’d say it’s a safe bet to listen to the welder when it comes to welding.
You have to use NON clorinated (sp?) Brake cleaner. Its the clorinated part in most brake clean that is dangerous, if you hit it with the welder it becomes dangerous. Finnegan went over this in one of his videos.
We used to JB Weld our Caterpillar Engine Blocks when they would crack, I remember filling in a .5 inch crack on a D-9 block that was 6 inches long and it lasted the life of the Tractor. which was 20 years.
@@AlexLopez-vx3cr that'd work maybe the manufacturer should do that. The wallet has around 24 tiny screws. I guess I was naive assuming the wallet would work without modification. Even you wanted to take the time to put thread locker on 24 tiny screws. You'd have to do it before they fell out and got lost, when you had no idea they'd fall out.
WHO_TEE_WHO I JB welded a 13hp honda engine block after the flywheel lost a magnet and smashed the magneto and mounts right off the block. There was 2 holes right into the block. I used brake clean to remove oil and then jb welded the mounts back on the block. After a week i reassembled the engine with another flywheel and magneto and ran it for years. Then i sold it working fine
You can grab a wire feed welder from harbor freight for about 100$. Its not pro grade or even close, but will stick shit together just fine. Perfect for the home gamer who needs a welder a few times a year.
@@Aint1S In all honesty, I despise C-clip axles. That design is just asking for a problem. Full-float hubs are the way to go man. No C-clips. Heck, if you need to remove the drive shaft, you chock a wheel and simply unbolt 4-8 bolts and slide it right out. No need to pop the diff cover or even remove any cargo from the vehicle.
I live in the u.k and have used it twice. Once to repair a cylinder head where the water in the engine froze popping a core plug and cracking the head by the sparkplug. The Second time I used it to put a fuel return pipe back on the tank where some vandal had snapped off to steal fuel. It is amazing stuff no doubt and worth every penny.
With everything i build and all the projects I've done.....i would love to link up with you guys. You guys are full of life and remind me of my brother lol
My shifter on my DRZ400 punched a hole in my gearbox about the size of a large donut hole. I slapped a washer with some JB weld and it ran great for three more years till i sold it! Saved me like $200!
Little trick guys, get steel metal shavings from the machine shop and mix it with the JB. It will make it strong like Iron Man ! This is what we used to do on the used car lot back in the day.
That's a really bad idea. The sweeteners will gum up immediately and it combusts at fairly low temps. Now using straight vegetable glycerin which is used in e-liquid might work pretty decently.
tbh your videos give me euphoria. you jump straight from the title into the question that got us to click on it, no clickbait sh**, and then right into your content. SUBBED!
You should have mixed up all 4 packs and put it in a zip lock cut off one of the corners and squirted it like cake icing while rolling the gears around to give maximum coverage and filled the entire void in the carrier!
I feel like if you coated the spider gears in JB Weld, spun one tire so it got in between all of the teeth, and then slathered the rest with what was left, it would have held.
PACE ARROW Bullshit, Homer. Us normal people point out that someone is a pervert because we're couldn't help but to notice when it's this obvious. Only a ignorant pervert would assume that must mean that we are a "closet case " because we expressed an opinion based on observation. So shut the hell up with that "closet case" nonsense. You look stupid. But again, your lifestyle includes feces eating. so...
Fixed a big hole in a oil pan, never let go, we cleaned with brake cleaner, then scuffed it up a bit with files, then used JB Weld, my FRIEND was AFRAID it wasn't gonna work, he hit a rock in his driveway, needed his car for traveling for work, he put over 125,000 miles on it later, then he sold his car when cluth was slipping at 325,000 miles, he got $1500 for it, only paid $2,900 at a car auction that i took him to, he saved about $1,500 on it. The guy was thrilled to only pay that. He drove it out of there.
Zarze 99 as someone who has personally seen both a carborated and an efi engine run on nitro I can assure you that it will run, not well, but it runs and but will completely demolish the engine it's in after continued use
They should have filled the gap around the spider gears completely then rotated one wheel until all of the teeth and crevices were completely filled with jb weld then filled the remaining voids.
Seth Francis Sim Racing well its actually a better idea. You'll raising the surface contact points for a better adhesion. So more surface area-more strength in bonding. So you probably can apply more torque. Any rattle or...ah no I don't wanna talk about Young's modulus.
I would think by doing this it would fill all of the gaps in the teeth and the gears would not be able to turn when the weld hardened. plus the adheasion of the jb weld. it would eventually break tho but i think it may have held for a trip or two.
@@acef3d It wouldn't be in the ring and pinion gears, which are the only gears that would still operate. The other spider gears you don't want to move, that's the whole point. They would only be completely filling the spider gear area, not the whole meatball.
![ลองสั่งของจากแอพ temu ถูกจริงหรอ?? ( part : 1/2 ) [โกงไหมครับ ep.89 ] | DOM](http://i.ytimg.com/vi/RTcZSQTiDZw/mqdefault.jpg)
Check this out !! We made a MOPED powered CAR : th-cam.com/video/MS4itA1dSjA/w-d-xo.html
Fill the tires with helium and drive off a mountain to see if you will fly
Wtf this is the dumbest comment I've ever read. Unless it's a joke...
Helium at equal pressure to air is actually more dense, so it would actually be heavier. Lol
That's why helium tanks don't just float away.
It's a joke about these guys driving off a mountain
nambinhvu oh that’s why heavy metal tanks don’t fly away thx
I'm sad you had to explain this.
Just wanted to point out that you should NEVER use brake cleaner (or any chlorinated solvent) prior to welding. Welding causes the brake cleaner to decompose into phosgene gas which is extremely toxic and can kill you.
just let it evaporate
He says that.
I used my jb weld on my wheelchair 4 years ago and it is still holding !!!!
It’s been over 5 years. America wants to know, is it still holding the wheelchair
6 now
@@jacobegnor4197 The wheelchair broke while he was near a stove and he knocked himself out turning the gas on. This caused his his entire apartment complex and every nearby building to burn down, killing over 9000 people. It was quite a tragedy.
@@Crashandburn999 Jesus Christ I never thought I’d see another one of me in the comments on od vids
Cool bro :D
Next try JB welding your wheels on instead of using lugnuts...
I wanna see that
It would work, until your pads or tires wear out
Yes
Don't give them any ideas 🤣
I just went through this on my Polaris sportsman the previous owner Jb welded the outer axle instead of a castle nut
JB Weld is actually a very good adhesive, with great tensile strength. My ME engineer buddy tested some lap shears, using this epoxy, and it had very similar results to adhesives used in the composites industry, but at a fraction of the cost.
I know, I used it on my wife. Very good stuff
try some tarzans grip lmfao@@linuxtuxvolds5917
Lasted longer than my first relationship
And 2nd, 3rd. But the 4th shall last for forever.
Awesome comment
10 months later still gold
F
"Shove it in there dude"
"Oh im shoving it dude. Dont worry"
"Those are some fat beads dude"😂😂😂
Anal beads?
Alex Youngberg yeah there was alot of suspect convo in this video
Oohhh Look at that chow :p
😂😂😂
3:09 don't do anal
Dude, this has been on my list for shit to do for years.
Omg its diwd. Good harley vid
Do It With Dan Danny boy
When you're a bike guy, and a car guy... And find another bike guy, watching car guy stuff.
Do It With Dan Yooooo
Love your vids Dan!
7:56
That's the laugh dumb people make...
Yeah, that's what I think every time I see them laugh. I like watching dumb stuff 😂
True
The surface has to be very clean when applying JB weld. Also you need to let it set for 48 hours for best results in a heated area.
It takes 48 hrs for the jb weld to fully set.
I don't really think it would matter.
Mr.Mister I work industrial maintenance and I'm not positive about this application but I've seen plenty of proof for me to always give it a full set time. Like concrete. Definitely not strong after 12 hours max they only waited one night then tried to break it hahaha.
In a case where JB Weld would work, waiting for the full cure is highly recommended. However, this is just not a good candidate for JB Weld.
I have made some pretty insane things out of JB weld, you are 100% right it is all about the cure time. I don't know if two or three packages of JB weld would be enough even fully cured... Kind of makes me want to try before I swap in my new rear gears and locker :)
I think with adequate surface prep, cure time, and 3x more jb it could possibly work for low stress applications
My grandpa jb welded his dentures to his gums, hes 70, and had to have them surgically removed😂
colinTheCat No way lol
James Ireland i shit u not my guy😂
Poor grandpa
Shit, I'd be worried about that tree that I came from if I were you. :D
MV60 you came from a tree... Dude.. there is a time and place for everything..
Coming from trees.. you're on your own.
I’ve been driving for 2 years in Alaska with my intake manifold JB welded 👌🏼👌🏼
James Rodriguez Prove it
why and where is it jb welded???
@@sity909 he probably added too much boost and cracked his manifold
Grand Marquis now has posi-track. Joe Dirt would be jealous.
Dude! Dude! My diff! Dude! Sick dude! Dude! Weld my diff; diff dude! Dude!
Yeahhhhh dudeeeeee
Fuckin stupid
Yes you're right, that is exactly what "bro talk" is, fuckin' stupid.
RevengeFromAngel a dude dude living ina a dude house with a dude car and dude windshield dadadidudududidadadaduuuude
Duddddddddeeeeeeeeeee my diff
drifting on the cheap should be a series on the channel
OMG frr
You clearly didn't see the haggard garage channel.
As you can see it no longer exists.
Turo Fonz lol
What is going on with this channel. Are these guys stoned 24/7 now.
If you have never smelled used diff fluid you're missing out.. Lol
Oscar Mayer worst smell ever
I thought transaxle oil was bad but this shit is just nuclear waste.
Fucking terrible...
Trans fluid is awful i can't imagine diff fluid lmao
It's nice, but I prefer smelling freshly pulled head bolts....
But can you use WD40 as diff oil?
Can you duct tape a diff to make it a welded diff?
KennyKGaming woke
No chows pee please
KennyKGaming Yes if you use flex tape
SAMMIT why would you that stuff is more expensive than proper diff oil
You should have packed it with JB Weld! Like basically fill it to the case with JB weld so the gears are bricked together! I honestly think if it was completely full it might work
That, plus let it cure for a couple of days. :)
That stuff looks like a bunch of thermal paste for a CPU😂
This is the dumbest thing I've seen this week and I LOVE IT!!!
1987FX16 Chris rudnik has a totaled skyline
Orion breaks in welds a diff
just a warning...do NOT use brake cleaner to clean welding surfaces...It’ll basically turn into mustard gas lol. Use acetone!!
Just killing some brain cells there
But I love the taste of mustard won't the gas taste the same
Phosgene gas is what you're looking for. WAAAY worse than mustard gas.
As long as it is non chlorinated it isn't a problem. Phosgene will only be produced by chlorinated brake cleaner.
Welding after spraying it on a surface to clean it won't do a damn thing, it evaporates. However, I had a coworker who sprayed a bunch of chlorinated brake cleaner through a Honda gx390 engine and it bogged down and came out as black smoke that burned his lungs and his exhaled breath was white fog for some reason lol Funniest thing I ever saw.
I can not tell you how long I've wanted to try this, lmao
i was gonna say you should of done it on the steve but thats FWD lol
Braden Carlson i can not tell you how much i hate you for this comment... Diff lockers are so cheap... Why would ypu do this except for views...
donnie hooker For personal entertainment, lmao. Why does this make you so mad?
Uhh to see what happens... and have a blast doing it. Human curiosity.
donnie hooker you ever tried one on a FWd? I want one bad a phantom grip im doing it regardless instead of welding
Im proud to see these young kids locking their diffs, I grew up on a farm Lincoln locking diffs was a requirement or your always getting stuck.
I wish there was way more content from you guys just like this, I love your videos
This is great lmao
This is great if u have an iq of a fucking hen
@@mcqcjc8409 this is all just for entertainment, sheesh.
U should have used word cheap. I guess it is on par with the entertainers.
Are u assuming that i was expecting it to work?
I once JB welded my oil pan... roughly 140k miles later (and 2 new owners) it's working perfectly!
can you use maple syrup to turn an open diff into an LSD?
all canadians use maple syrup in their diffs - fact
Captain Zoll syrup as diff oil 😂
Can you put cement mix into a diff to weld it? That would be cool
Pack it full with moly grease instead.
Captain Zoll LSD's are fine, but shroom diffs feel more natural.
In conclusion I'm jb welding my transmision case 👍
Just for a warning! Cleaning parts that will be welded with brake parts cleaner is NOT safe. When you weld a part that has been cleaned with brake parts cleaner it creates toxic fumes.
Really toxic, potentially phosgene toxic.
You are wrong, Brake cleaner is designed to evaporate very fast, you have never used any parts or brake cleaner have you? I fix motorcycles for a living .
Yes, on a flat, polished and clean surface brake cleaner evaporates quickly, on material with deep pits or crevices it can remain. I don't know if you weld, but it's a real hazard if you arc weld with a gas shiled. This is a well published phenomenon to the point where practical welding was breifly introduced during my freshman yeae of engineering we all had to sign to say we had listend to the safety warnings, been given a written copy and read it. Modern brake cleaner is less likely to be chlorinated, but if you happen to use a chlorocarbon to prep before arc welding with a gas shiled there's a very real risk of phosgene.
Uncle Quack really? You fix motorcycles for a living? That means you change parts in and out? How much welding do you really do? I bet it’s squat in comparison to me. I’m a welder for a living! I’d say it’s a safe bet to listen to the welder when it comes to welding.
You have to use NON clorinated (sp?) Brake cleaner. Its the clorinated part in most brake clean that is dangerous, if you hit it with the welder it becomes dangerous. Finnegan went over this in one of his videos.
Next tests: Can you flex seal a diff? And casting molten aluminum in a diff
Orion asking all the important questions project farm doesnt
haha project farm.. can you use jbweld as gold?
Can they use a 3D printed header 🤔
Onion*
Do a segment on different materials for drive shafts, wood, pvc, concrete etc...
We used to JB Weld our Caterpillar Engine Blocks when they would crack, I remember filling in a .5 inch crack on a D-9 block that was 6 inches long and it lasted the life of the Tractor. which was 20 years.
I like how you say you clean before welding with breakclean.... you probably should stick to jb weld you shouldn’t touch a welder 😂😂😂
Just hold your breath
tortron say that when you inhale and your meeting god 🤷🏾♂️
Thinking the same
You obviously dont understand that the brakeclean cleans it your supposed to do that lol
@@triix5 if you weld something with brake cleaner it creates phosgene gas and sort of kills you.
Jb weld didn’t hold my bellhousing but you never know
Don't use brake cleaner prior to arc welding. It creates a poisonous gas that will kill you. Look up phosgene gas.
They are still alive tho
If you use non-chlorinated brake clean it won't create poison gas.
You should fill the whole diff housing with jb weld.
Nick Rittenhouse I can’t get the damn axles out! WTF!
If this isn't the best ad for JB Weld I've ever seen...
I got one of those wallets. The screws fell out after a month or so. Complete garbage.
Tracy Goodlett 😂
Just like their videos.
Put some thread lock on it. Lol.
@@AlexLopez-vx3cr that'd work maybe the manufacturer should do that. The wallet has around 24 tiny screws. I guess I was naive assuming the wallet would work without modification. Even you wanted to take the time to put thread locker on 24 tiny screws. You'd have to do it before they fell out and got lost, when you had no idea they'd fall out.
Also those have to be for front wallet people. Theres no way I could have that in my back pocket
I'm in the UK so I don't stand a chance of winning anything from you guys, but its fun watching you.
Thanks for the laughs and fun stuff.
Ofcorse they let go, you didn't fire clean the brake cleaner first. There are still small amount of fluid mositure on the gear.
i bet you cant drive with peanut butter on the steering wheel ;)
Well have a dog in the front seat, while trying this. {A big dog}
Bowtie Thirteentwenty or put the dog in the back of an IQ like James May did once
I cant believe it held on that long ! JB Weld is serious S**t ! Great Video !
oh my god i realized today i havent watched a haggard garage video in about a year and a half the progress is real this is insane wtf
props Orion
I tried to JB Weld the key on a motorcycle crankshaft one time... It failed immediately
WHO_TEE_WHO Who Tee! You crazy, bro!
All you needed was a bastard file a new key, and a lot of time.
Didn't expect to see you here haha!
WHO_TEE_WHO I JB welded a 13hp honda engine block after the flywheel lost a magnet and smashed the magneto and mounts right off the block. There was 2 holes right into the block. I used brake clean to remove oil and then jb welded the mounts back on the block. After a week i reassembled the engine with another flywheel and magneto and ran it for years. Then i sold it working fine
You didn't wait long enough
I seen jb weld hold up in a crank case of a crf 450 .
You can grab a wire feed welder from harbor freight for about 100$. Its not pro grade or even close, but will stick shit together just fine. Perfect for the home gamer who needs a welder a few times a year.
Watching this taught me what the difference between differentials
Every video I've ever seen from these guys is basically just the automotive equivalent of hitting an iPhone with a hammer.
Best thing about welding diffs is that you remove all the nasty hardening from the steel parts
LMAO, but what are c-clips?
@@Aint1S C-clips? Pay no mind to them, just the man tryna keep you down
You're killing me man, LMAO! I like your style 😂👍🏼
@@Aint1S In all honesty, I despise C-clip axles. That design is just asking for a problem. Full-float hubs are the way to go man. No C-clips. Heck, if you need to remove the drive shaft, you chock a wheel and simply unbolt 4-8 bolts and slide it right out. No need to pop the diff cover or even remove any cargo from the vehicle.
Darren
Flex Seal diff??
flex seal is basically rubber so it will just fly everywhere
THATS ALOT OF DAMAGE
"look at those beads, I'm gonna lay a phat bead right here" oh damn.
@@garystinten9339 He said beads dude lmao.
word of wisdom from a man who has a welded diff still going strong from the 70s: weld a bunch of washers and bolts in it, it helps
I live in the u.k and have used it twice. Once to repair a cylinder head where the water in the engine froze popping a core plug and cracking the head by the sparkplug. The Second time I used it to put a fuel return pipe back on the tank where some vandal had snapped off to steal fuel. It is amazing stuff no doubt and worth every penny.
Dude, did you remember to JB WELD IT?
"CAN YOU USE ELMERS GLUE TO WELD YOUR DIFF??"
Probably use that big ass nose
Smashing
No.
Rubber cement!
With everything i build and all the projects I've done.....i would love to link up with you guys. You guys are full of life and remind me of my brother lol
My shifter on my DRZ400 punched a hole in my gearbox about the size of a large donut hole. I slapped a washer with some JB weld and it ran great for three more years till i sold it! Saved me like $200!
Little trick guys, get steel metal shavings from the machine shop and mix it with the JB. It will make it strong like Iron Man ! This is what we used to do on the used car lot back in the day.
Dukes Mayonaisse as oil
Attempt #4
That's not mayo dude!!!!!!! wth
Can you try and use vape juice as engine oil please
$100000 later
That's a really bad idea. The sweeteners will gum up immediately and it combusts at fairly low temps. Now using straight vegetable glycerin which is used in e-liquid might work pretty decently.
A tube of quick steel would have probably worked better. You can pack it in there like playdoe and it’s harder than jb weld
Looks like poor adhesion was the failure mode here. Needed to be cleaned better and surfaces scrubbed with a wire brush or sandpaper
Jake Heke 👈😎👈
Jam bolts in the 4 corners between the teeth then use quiksteel
right on
Krankie V sandpaper should be used right here cuz the teeth are well hardned. And yeah, pure adhesion failure mode right here.
tbh your videos give me euphoria. you jump straight from the title into the question that got us to click on it, no clickbait sh**, and then right into your content. SUBBED!
You should have mixed up all 4 packs and put it in a zip lock cut off one of the corners and squirted it like cake icing while rolling the gears around to give maximum coverage and filled the entire void in the carrier!
Next time on Onion OD. "Can you make a fleshlight out of rolls of pennies? "
Brought to You by the NoGirthGang.
You should try putting flex seal in a diff and see if it acts as limited slip diff.
i wondered why all the jb weld's from my walmart were gone
haha, u went to walmart to buy JB weld to try this!
It's probably won't stick to the diff itself normal but the hardness of the JB is awesome, that's what's probably keeping it locked.
Video summed up in 10 first seconds. Saved me 9 minutes of my life.
Step 1 fill tires with cement
Step 2 buckle up
Step 3 drive into nearest lake
A bunch of knuckle heads. Lol. Were can we hang out lol
I made a JB Weld hood exhaust
Brake cleaner is honestly God tier, I clean myself with that shit
I feel like if you coated the spider gears in JB Weld, spun one tire so it got in between all of the teeth, and then slathered the rest with what was left, it would have held.
You should try to seal a cracked engine block with jb welds
icycoldfire4 that actually works...
Repaired a head on a v10 ford lasted 60k then went to auction still holding strong
Repaired split water jackets in a 20R with jb, worked for the rest of the engine's life.
Richard Roper 20rs need coolant? Lol
Jake Browne lol had a bad flash freeze one winter
When in doubt Walmart to the rescue!!!!
If you cannot be arsed to weld it properly you deserve every bit of breakage you get
Goes through tires real quick when you do that. Lol
He says jb weld does wheelie good 😂
this is gonna be bad hahahaha
Clutch Kick Junkies very two clutch kicks on a manual and its gone
These guys all make my gaydar overheat. They really are putting something in the water to make the friggin frogs gay...
Agree
Lool
Man, people get so salty over this channel. Jealous that you don't have $500 to buy a Craigslist beater to play around with?
I thought everyone knew that but I guess not
PACE ARROW Bullshit, Homer.
Us normal people point out that someone is a pervert because we're couldn't help but to notice when it's this obvious.
Only a ignorant pervert would assume that must mean that we are a "closet case " because we expressed an opinion based on observation.
So shut the hell up with that "closet case" nonsense.
You look stupid.
But again, your lifestyle includes feces eating. so...
No gloves? Brutal.
Fixed a big hole in a oil pan, never let go, we cleaned with brake cleaner, then scuffed it up a bit with files, then used JB Weld, my FRIEND was AFRAID it wasn't gonna work, he hit a rock in his driveway, needed his car for traveling for work, he put over 125,000 miles on it later, then he sold his car when cluth was slipping at 325,000 miles, he got $1500 for it, only paid $2,900 at a car auction that i took him to, he saved about $1,500 on it. The guy was thrilled to only pay that. He drove it out of there.
i JB weld my AC lines, worked like a charm!
without watching the vid i can tell you it will break
Can you run a car on rc nitro fuel? 🤔
Serioga Markovas you can untill either the engine blows or your wallets runs out of money cause that shit is expensive as fuck
Ethan Knight no
no because nitro fuel has a higher flashpoint than gasoline. i mean it will run for a bit but your injectors and fuel pump are not going to be happy.
Zarze 99 as someone who has personally seen both a carborated and an efi engine run on nitro I can assure you that it will run, not well, but it runs and but will completely demolish the engine it's in after continued use
It would blow up very fast. It’s alcohol based which will cause it to run hot.
you guys are exactly like me!!!!! I fucking love yall!!!! I JB welded my JB welded my axel😂😂😂😂
Orion!!!! Killing it with the personal channel never been better keep it up dude.
*Can you use Flex Seal to WELD your DIFF?*
bellcc2 flex seal head gasket
Only works for making wings to fly through the sharknado or putting a screen door in the bottom of a boat
Dude you so........ Dude dude dude
They should have filled the gap around the spider gears completely then rotated one wheel until all of the teeth and crevices were completely filled with jb weld then filled the remaining voids.
Seth Francis Sim Racing still wouldn't have held.
@@tonyp8808 yea your probably right, I just would have liked to see the result.
Seth Francis Sim Racing well its actually a better idea. You'll raising the surface contact points for a better adhesion. So more surface area-more strength in bonding. So you probably can apply more torque. Any rattle or...ah no I don't wanna talk about Young's modulus.
I would think by doing this it would fill all of the gaps in the teeth and the gears would not be able to turn when the weld hardened. plus the adheasion of the jb weld. it would eventually break tho but i think it may have held for a trip or two.
@@acef3d It wouldn't be in the ring and pinion gears, which are the only gears that would still operate. The other spider gears you don't want to move, that's the whole point. They would only be completely filling the spider gear area, not the whole meatball.
Every time they say "JB weld" take a shot
🤣 he said it feels really good in my pocket actually
You guys should not be allowed near cars.
Will Sloan by the looks of you.. you shouldnt be allowed near kids
@@bradrarkus604 Oh god im dead.
Pow!! Will Sloan you cant come back from that.. dead
@@bradrarkus604 OOOOooooof...
@@bradrarkus604 Oh ma lordy
Your next video should be Can you use gatorade as coolant
I think that would make a great video!!
It's got what plants crave!
i literally cannot finish to watch the vid, that accent is so upretting:D
does working without welding. awesome!!
I have missed many many videos bro. But i just watched the last 3 and man im happy for you. Keep having fun bro