P80 Glock trigger reset and most common issues GUARANTEED FIXED
ฝัง
- เผยแพร่เมื่อ 8 ก.ค. 2024
- Every P80 issue solved by JARG.
Fixed trigger reset, stuck, crossbar angle, light strike, Timney, feed, slide
Disassemble
• JARG discusses P80 Glo...
Trigger Reset Crossbar Angle
• P80 Glock trigger FIXE...
Slide Creep and Polish Safety Plunger
• Video
P80 in Recover 20/20 Brace with upgrades
• JARG upgrades Recover ...
P80 G17 Frame Cut for G19 mags
• JARG cuts P80 Glock 17...
P80 with Timney ALPA Trigger
• JARG installs Timney A...
Timney Trigger Bar fixed/Grinding
• JARG has Gen 5 Trigger...
P80 Feed Problems and Cycling Issues
• JARG’s P80 Glock 17 fe...
Polish Glock Internals
• JARG polishes Glock in...
Light Safety Plunger install
• JARG installs light we...
![[TH] VCT Pacific Stage 2 - Week 4 Day 3 // GEN vs TS | PRX vs ZETA](http://i.ytimg.com/vi/nspkjQuZve0/mqdefault.jpg)
I watched your trigger rest video. I watched several before yours and all mentioned polishing as well as spring issue in slide. Your video is the 1 that helped fix issue. Thank you
One thought. IF you are having trouble with the shells ejecting erratically, there is a fix. I noticed that in the video you are still using the original Gen3 ejector rod. If you replace this piece with the Gen4 ejector rod you may find as I did that the shells eject in a more uniform direction and pattern. Lone Wolf Dist. has this part for around $5.00. The part number is LWD-30274. You can order it by itself as Bare Ejector Rod. I appreciate the info on polishing the safety catch and trigger bar. Back to the workbench!
Thank you sooooo much!!!!
Bending that cross up fixed my issue.
YOU ARE THE MAN!!!!
I purchased a registered P80 PF940V2 G17 size and polished the trigger bar and changed the firing pin spring and then my trigger became binary 🤯. Went back to the stock P80 firing pin spring and no more binary mode thank god. But i am getting ready to start some different P80 builds. So I’m scouring for videos and info on does and donts and solutions. So I thank you for your videos.
Hey boss, I watched this video a few months ago for advice. It helped in my case, only now the striker firing pin sheered off so looks like I'll have to get another striker. Gotta love aftermarket MIM parts. Anyways, just came across this video again and wanted to make sure I said thanks, your video is the only reason I was able to figure out my trigger reset issue.
Check out my other videos. I have a folder of P80 shorts. I just did about 5 shorts on P80 problems. Like and Sub. YT hates 2A
Keep up the great work ur videos are awesome 🤙🤙
Great video! Thanks for sharing!
The first issue you described I'm willing to bet is my problem. Thank you.
Let me know
Lol I have done everything you said except a longer firing pin.
Thank you sir!!
Great content
U got a bad ass build brother
'Polished the dome'😂😂😂 Sorry, that was funny.
Thank you
having a problem where the firearm in in battery one in the chamber . At this point if I try to rack the slide back to unload the round the slide will not come back unless I depress the trigger.????
I've built 2 p80s so far just completed my 2nd one and on both of them I've had the exact same problem and it's the damn shark fin height.. I had to shave down both of my p80 fins.. and my 1st slide was from live free armory and my 2nd is leo precision Symmetry slide.. and both times I've purchased my lower and upper parts kit on ebay...
never again..
I had an oem trigger housing in my p80 that moved too much. The over travel OC housings off eBay fits amazingly better and doesn’t move at all.
The best thing anyone can do for their P 80s or Glocks is the Timnely trigger IMO. Unless a 3 lbs. trigger is to light. I have a lot of Glocks and 3 P 80s. All but one have the Timnely trigger and it a new P 80 that I haven't tried yet. Use the RED spring in the Timnely trigger kit, it will add a little pull weight but makes it much more reliable on the return. I haven't found the need to do anything to the Timnely trigger other than the Red spring. Also I had problems with the P 80 trigger housing, I use factory Glock trigger housing and found they work better for me.
See my Timney review in P80. Fit problems in Gen 5
@@JARG Thank You, I have 2 or 3 Gen 5s and the others are Gen 4s in the Glock line. If I remember right, the Timnely triggers are Gen specific as to Gen 3-4 and the Gen 5s. Again Thank You, P 80s can be a long learning curve as most have found out. I don't think many get them running right after building them. They seem to need to be tweaked on, some more than others lol. I know mine have had their fair share of failing.
Great video. Hopefully this help with my current problems. P80 and lone wolf 80 Glock 19 clones. Fail to feed, stovepipes, slide gets stuck part way fwd after feed so I have to whack the back of the slide fwd. I was going to polish the ramps and slide rails, then apply more lube. I only ran 1 or 2 mags of rounds thru each, so I thought it could also be break in issues.
Guide rod Spring. No doubt
th-cam.com/video/H1qZDmd3LNk/w-d-xo.html
Let me know. It will work
Do u think it’s my cross bar angle is my trigger only resets if I don’t have my finger pressing down on it if I do it won’t reset but I took my backplate off and manually pressed in the lug to across the cross bar and it’ll reset w pressure but with a backplate on nothing
Yes trigger bar angle
I have a question for you. The trigger resets and it travels perfectly without any play, but it fails to engage it to be in the firing state (cocked) initially it didn't have this issue. Aside from it not cocking you wouldn't be able to feel a difference between this one and one not malfunctioning
Possibly too high of a rear angle on your cross. Sounds like the trigger is not dropping
Thanks, when I have a chance I'll tear it apart, so I need to bend the angle on the trigger bar? Also have you thought about doing any AR videos because I feel like you would be really through with explaining common issues and difficult steps in the building process that could help along of us out. I haven't started on my AR build yet but I've got a feeling it's gonna be a fun one
I have a problem with a p80 build that I hope you can help me with. I bought a ryg phantom trigger but it seems like the trigger is not far enough forward, the saftey blade on the trigger hangs up big time on the frame. Have you ever experienced this?
Is the PRETRAVEL adjustable?
Uhh mine shoots twice with one trigger pull. Shot I one time at the range and haven't shot it since what should I do? Has agency arms trigger.
@@gizmakthegushaa5707 slipping over the cross bar
I have a problem with my p80 slide that I can't seem to find help for online. My slide cycles perfectly with no mag or with a mag, like butter. But if I put a round or snap cap in the mag and then rack the slide, once it resets and loads the round into the barrel and the slide goes all the way forward, it then locks onto something so the slide wont go back again. It's hitting something or whatnot and you have to muscle it as hard as u can for it to release and the slide will then be able to go back, eject the round, but when the slide spring returns it forward again, it's locking shut again. Take the round out and the slide can be racked back perfect. What can it be hitting? It's like the first eighth of an inch of travel back is locking
Sounds like the front of your locking block is binding in the slide. What marks does it leave
On the front locking block the cross member that connects both sides seems to have some scratches a little. But like I said, it only does this when the mag is loaded, works perfect unloaded.
One question, should my shark fin be coming dead center over the top of the plunger?
Ideally but might need to polish it and use lighter plunger spring
See other P80 video I did about plunger
Great info. Thanks! My P80-32 has an extremely mushy trigger. When pulling it, it goes all the way to the back, sometimes fires, sometimes not. When I release pressure and reapply pressure it usually fires. This is when dry firing, and when loaded (only tried one round). I have oiled it properly, and made sure the trigger bar isn't rubbing too hard on the frame. Any thoughts?
Initial thought is cross bar angle is Too high in the rear. Possibly too strong of a trigger spring. Where is the wear mark on strike lug?
I have that mushy trigger as well, sometimes fire and sometimes not when dry firing. Took it to the range and it has a hang fire. Not sure how to fix it and can’t find any videos how to fix a hang fire
@@JARG any info ? Thanks in advance!
@@Semper_haulin where is your wear mark on your firing pin lug? Send me a pic to justaregualrguy21@gmail
Possibly back of your crossbar is a little to high. Or your connector is not correct and the crossbar bar is not dropping
Could anybody help me out with binary trigger not working/ not moving completely at all like it’s stuck unless it’s manually handled on myp80 handle. Help ?
I wish but never used a binary
Any known issues and fixes with a P80-19 and Advantage Arms 22lr conversion?
I do not know. What is the issue?
@@JARG basically #'s 1&3 from this video but the design is a little different. Gen 3 BTW.
Hey, I have an issue with it not shooting where I aim, how can I zero in the gun?
Adjust the fixed sights
Your videos are so helpful. Now I am having a "double tap" automatically. The first round fires perfectly and then when the trigger goes to reset a second round fires. Any ideas to fix?
th-cam.com/users/shortsOKupkdfG_nk?feature=share
I’m 99% sure
@@JARGthank you sir!
I’ve got the Alpha Timney Trigger in my P80 as well. I can’t get it to reset. Everything installed great. I actually followed your installation video. Any tips on getting the timney trigger to reset?? Thank you.
What is it catching on?
@@JARG i believe the trigger bar is rubbing slightly on the polymer frame. I haven’t got around to grinding any metal off the trigger bar yet but will definitely give that a try as I seen on one of your previous videos. Could this be this issue? It’s the only place I see friction.
I have identified all spots where there was friction and eliminated all of those spots. Trigger still not resetting. Any tips? When I try reset the trigger it releases the firing pin as if pulling the trigger.
My trigger resets everytime except during live fire. It ran more frequent as I fired it but even 300 rounds didn’t solve it. Also got light primer strikes and failure to return into battery. Could it all be one thing doing this?
Liner the recoil spring. See #3 most common problems video on my channel
Mines When I Put the Little Pin on It Wont Rack Right It Gets Hard Don't kno Why, Maybe Need to Polish the Rails
I Need Help with This Issue as NOBODY Here knows about It I think that Im the Only One with This Dam Issue, JARG I NEED YOUR HELP BRO!
Can I please get some help with my issue on gst-9 build. When I dry fire the pistol the slide seems to move forward about 1/2 a mm. I have all glock oem components in both lower and slide. I noticed that the barrel seems to rest on the ejector? Is this how the mechanics are supposed to work? Doesn't seem right. If I remove recoil spring from slide and push back on barrel towards ejector, you can see where the ejector springs back some and the barrel will sit flush with slide until pressure is removed. With the gun assembled and the trigger in the back position (after firing of gun) the barrel is nice and snug as it should in the slide....as soon as I rack the slide and the trigger moves to the forward position that hairline gap appears again (between back of barrel and slide). I have tried switching out all slide internals with no luck. If I remove the slide internals (minus the firing pin) and re-install the slide no gap...re-rack and no gap...fire and no gap...I am lost on this. The only thing I can think of at this point is that the slide is slightly out of spec.
The problem is your recoil spring
Watch my video on P80 Slide creep. I think I switched to the 20lb recoil spring. What weight is your current recoil spring? Also what weight is your current firing pin spring?
Watch this video 1st
th-cam.com/video/H1qZDmd3LNk/w-d-xo.html
If it works like and subscribe
Hey Guy, so I went to test my new GST-9 mod1 build, and it randomly shoots full auto or in 6 round Burts. Why do you think this would happen??
Your firing pin is slipping over the cross bar while your safety plunger is being depressed. Your crossbar angle is off
I have problem on part 30274 I attached it the gen 4 ejector on gen 3 g19 when I attached the slide doesn't wanna slide till end by ejector tip after metal any help plse any ideas?
Not understanding the problem
Sounds bent. Make a video and send link
I need help why is my p80 trigger hard to pull and my slide wont slide all the way back im using OEM lower parts
Slide is possible that you have wrong gen barrel or your slide rails are bent. Try is on another frame to rule it out
Trigger difficulty is either Shark fin Hitting safety plunger at wrong angle or trigger bar angle is too high and it never break/drops to fire. Or parts of the trigger is rubbing in the gun
My p-80 fires once and doesn’t shoot, I have to re rack it to get it to shoot, and jams again and yeah it literally a bolt action lol😊. Can you help me?
What is it doing? Trigger not resetting? What do you mean by jam?
Any ideas on a Dead Trigger?
After racking slide and then pulling trigger nothing happens..
I tried another Slide on lower and it functioned fine.
Cannot seem to figure this one out..
Is trigger stuck forward or just not firing?
Or stuck rearward
It's not firing after racking.
Trigger is free and not stuck..
When I use another upper it functions perfecly..
Yeah i fixed the reset problem but now the trigger won’t set back to the original state it’s just reset reset reset now i can’t take my slide off?
See my vid about slide removal with trigger struck
My p80 g26 if having problems feeding and ejecting the shell just stays inside it doesn’t come out could tell me what should I do to help fix that problem ?
Sounds like an extractor claw issue
What happens if you eject manually
Also what pound guide spring is in it
For some reason my rwb mag works well with my p80 I have no problems to feed but with my gen 5 glock 19 mag every round gets stuck on the barrel feed ramp any idea how to fix this problem?
What part is getting stuck?
@@JARG I check out your failure to feed video and the same problem you were having I was so ima change out the recoil spring and see if that changes it. It's still werid the oem mag is the one I'm having trouble with but we'll see if this fixes it
I have a p80 I built and almost every time I rack the slide fast while holding the trigger down and then release the trigger to reset it it sounds like the firing pin fires and doesn't reset . I tried changing the spring and plunger it's better but still having the issue.
Your crossbar angle is off 100%. Means it’s not resetting til after firing pin is sitting on the safety. Your shark fin is activating the safety and a small strike forward happens
That was the problem thank you very much! 👍👍
I have a problem if I put the back pin in it doesn’t work but if I have no pin I can reset and pull it
What happens when pin is in?
Sounds like it’s slipping over the crossbar. If the pin is not holding the rear trigger housing down, the striker lug is catching the rear of the crossbar and it will then work. That is the best diagnosis I can do without knowing more
can you drop the firing pin link? getting light primer strikes
th-cam.com/video/2SOIS14tIq0/w-d-xo.htmlsi=qiUSoYxPVJgWExW2
Should be this one
Hey brother. I have a p80 glock26. It fires. It loads.I can cycle rounds just racking. They expell fine. But when I shoot it. It doesn’t expell on its own. I can rack it and shoot again. No problem.
@@mitchellfrost7467 possibly extractor issued. Or try a heavier recoil spring. Seems like slide is moving fast and not gripping the casing
I tried changing the extractor. And same issue. I’ll try the spring. Thanks bro
@@mitchellfrost7467 what spring is in there? If slide is not moving after firing… you may need a lighter spring. I misread the first message
How about on a Glock 43, trigger feels normal with no slide, I put the slide on, trigger resets, but if I press the trigger it’s just all mush and never trips. Then my slide is stuck on the lower and have to remove backplate. Happens 100% of the time
If trigger won’t reset, then lug misses the cross. 100%. If other symptoms… could be something else. Not likely
@@JARG with the slide off the trigger is able to break and reset, with the slide on the trigger will not break. So you think this too little engagement from the cross?
When racking the slide, if I hold the trigger back, instead of resetting the trigger, it fires. If the trigger is released, the trigger will reset. Will the angle help me?
Yes. Watch the run away gun video then watch the cross bar video in the description
Run away. th-cam.com/video/tNbeX1zTzZ4/w-d-xo.html
Hey bro I’m having the same problem were you able to fix it if so let me know i would really appreciate it
@@angelledesma2596 you find out?
I have a p80 slide on a Zev OZ9. Purchased an Apex trigger kit and if I rack the slide with the trigger firmly pressed, my trigger fails to reset, if I ever so slightly put some backwards pressure on the slide it releases the trigger and I get a reset. I have a feeling its #1 but I won't be bending it I'm going to try to take off some material from the top since it's so close to reseting on its own. I will report back.
It’s #1. No doubt.
Look at my recent video that is a detailed view of the bending
th-cam.com/video/wGw5aDG09dQ/w-d-xo.html
@@JARG thank you so much. 🙏
@@kdworak4754 Did you fix it?
I installed an apex trigger, and trigger bar. It functions perfectly. I went to install the apex ultimate safety plunger and when you hold the trigger for reset it automatically fires. Any thoughts?
Yes. Firing lug slips over the cross bar
th-cam.com/video/tNbeX1zTzZ4/w-d-xo.html
@@JARG
Thanks for the response. It only happens with the apex ultimate safety plunger. I just put the stock one back until I can figure out why it is doing that.
@@JARG
I sent pictures of my frame and slide to apex. I reinstalled my oe safety plunger which works perfectly until I can figure out why the ultimate safety apex plunger is not working properly.
I’ve built like 6 or 7 P80’s at this point but I just did my first 10mm one and I’m running into an issue I’ve never experienced before and am not finding any solution online. When I pull the trigger I don’t get a “click” it just feels mushy and goes back into place when I let go. I haven’t tried live ammo yet just dry fire. I tried bending the trigger connector slightly as I saw that as a potential solution in a video but that didn’t change anything. Could it be that I need a stronger spring for the firing pin safety? Thanks in advance for any insight you can provide, I’m pulling my hair out over here lol
Either the angle of your crossbar is too high in the rear and it’s not dropping to allow the the firing pin to go forward. See if you have high wear marks on striker lug
Or your shark fin I hitting bottom of slide before the striker firings
Does the trigger get full travel or short?
Let me know more details
@@JARG it has full travel. Do you have Instagram or something where I can send a video?
@@spencerbrown6325 justaregularguy21@gmail.com
I have a question my p80 19 fails to fire but when it does it still make a click is that lite primer strike is that dealing with the weight of the spring for the striker system and if so what would you recommend for the best reliable weight for the spring?
Could be needing an extended firing pin. Spring 5-6lbs. I have several other videos. One is on slide creep and lite strikes
th-cam.com/video/2SOIS14tIq0/w-d-xo.html
@@JARG I'm ordering that same striker system you recommend in the video tonight early morning tomorrow on my way to work it says 30 dollars for it and that guide rod in the other video I'ma get that as well
@@dariusreynolds2431 where you ordering from
What is the name of it? I can’t find it
My friends P80 worked great for a 100 rds. Then trigger froze. I helped him build, so I said I’d take a look. Removed slide to look and now it goes on but will not move pass normal resting place. Will not move. I hear it hitting metal. I took 100% of parts out and transferred to different lower and worked great. Put 2nd P80 parts in 1st lower, same think. Slide frozen. Sounds like lower, but holes are perfect and everything looks normal. I’m at a loss. Any ideas would be appreciated.
Thank you, Joe
Make a few min video and post to your channel. I will try to help
Any time that I have seen the slide lock… The barrel was a wrong generation
Don’t have the p80 in my possession. Barrel is not the problem. Whole slide is Zev. Works on other p80 frame.
hey so i'm having a problem with my p80 g26. When I rack the slide back the trigger doesn't reset at all unless i push it upwards and no matter how many times i do it it still won't reset. i can send some videos of it but im honestly dumbfounded by what to do. this is my first p80 so i know im going to run into some issues but i can't find any videos that are really having the same issue as me, but thank you if you can help me.
Short like 15 seconds
So your trigger won’t reset unless you push it forward… is that right
@@JARG Yes, it won't click or reset no matter how many times unless i manually push it forward. i could email a short video of me showcasing what it is but thats really it
@@vanillatec529 justaregularguy21@gmail.com
I’m having the same issue w my g26
Geez, nothing like having to re-engineer a Glock.
That's what you sign up for when you build guns like this. It's just gonna happen every now and then no matter what, tolerance issues will always be a thing.
I put the aftermarket slide but the trigger won't go click. Not sure what my issue is.
Won’t click. Be more explicit
Pin doesn’t fall?
Let me know
@@JARG Pull trigger back and nothing happens. With a Glock OEM slide it will go click. Normal function. Bought an aftermarket slide and I pull the trigger back nothing happens. I heard it described as a dead trigger. Goes back no engagement. Like I said the Glock 43x slide works fine the aftermarket one doesn't engage at all and trigger goes back.
Just got a glock clone took it to the range and 20 shots in worked great then all of the sudden started to shoot 3 bullets on 1 pull. Help😊
Cross bar angle needs to be higher
I have several videos on bending the angle. Check my P80 playlist
My slide moves back when I pull the trigger and the trigger won't fire. Not sure what's wrong
See my vid on slide creep
th-cam.com/video/H1qZDmd3LNk/w-d-xo.html
@@JARG thank you sir. Your the only person on TH-cam that went out of their way and helped. I appreciate you.
@@JARG just a guide rod and recoil spring should fix it ?
I answer every person. Please subscribe and tell friends
My Glock 23 slide won’t rack all the way with dummy rounds in whenever it’s racked back n extracts a round, the slide has to be pushed forward, any ideas?
As far as push forward…. It’s your spring. See my video on slide creep. It’s in the description
Send me a 10 sec video showing the problem
@@JARG how should I send it? Should I jus post it on my TH-cam or email? Tryna look for it and I appreciate it!
@@arthurr151 justaregularguy21@gmail.com
If you need to do a longer vid. Post to your channel and let me know
Another thing: If the trigger bar is rubbing too hard on the side of the magwell it will stop the reset. Just sand it down and smooth it and itll go.
Sounds like you been watching my Timney Gen 5 video
@@JARGNah I just fixed it on a printed frame like 12 hours ago after a couple hours of tinkering. I'm sure I'm late to the party but gotta mention it just in case.
@@JARG You are a legend for teaching these fixes
Did you ever hear of the P80 Front Locking Block Pin Or Trigger Housing Pin causing trigger inconsistencies? I left it out altogether and it resets perfectly without it. Is it necessary if the G19 doesn’t have one?
Not sure. Don’t that would help a reset issue
@@JARG I think it’s causing additional slide drag which contributes to an inconsistent reset.
My trigger won't reset unless I'm holding the trigger. So regular racking won't do it except for the first time
Post a video on your channel. Tell me when up. Sounds like crossbar angle or connector
@@JARG I will this afternoon, in the mean time have you ever had an issue with the slide lock spring not wanting to sit down flush in its slot. my spring has a slight curve on the end where it goes into the slide
@@JARG nevermind I snipped a tiny piece of the spring and now everything functions nicely
Hey Jarg, I have tried my hardest to get the timney trigger to function properly. I have installed and reinstalled at least 5 times. I'm getting failure to reset. I have tried both the red and silver return springs, but still getting the same issue. I am running a minus connector which I have polished. You mentioned you had to grind down the trigger bar for the timney, did you try sanding a few thou off of the frame instead of the bar? Also what were your failure to reset look like?
Yes did you watch my 3 Timney Reset videos
@@JARG I have, I'm also using a p80 frame, so grinding the slide release won't pertain to me.
@@alexvu7686 when you pull the trigger, where is the friction. Something is holding your trigger The frame, connector, etc. where is the friction. Have the slide off and look at where your parts are rubbing
Hey I made a Glock 20 p80 and have trigger problems completely won’t dry fire lmk if u could help.
Tell me a little more about it
@@JARG I have a short of it posted on my channel but the guy I ordered from said it’s probably the connector and sent me a new one
@@bandzz.4036 I saw you video
@@bandzz.4036 I think it’s your connector or your cross bar angle is too high in the rear. You are pressing the sear into the striker lug but the sear never falls so the lug just pushes your trigger back forward from the weight of your striker spring
@@JARG you think the new connector will fix it?
my slide won’t rack all the way back
Send me a quick video on it
Help! My slide seems to behave, but my trigger just gets heavier and stiffer with every pull until it locks up. Then I have to rack it a bunch to get the trigger to brake.
Post a video on your channel. Tell me when it’s uploaded
@@JARG ha! With the Biden admin watching? No thanks. No disrespect though. I appreciate what you're doing. Also, fixed my prob with 220 grain paper and vegetable oil. 😉
How can I email you? Have a video I’d like to send you of mine and get your thoughts.
justaregularguy21@gmail.com
my trigger won’t reset unless i rack the slide twice, how do i fix that? what is the issue causing it to do that? the trigger bar kinda seems a bit high but i’m not sure if that’s the issue.
Likely cross bar angle
If you pull trigger and don’t hold it back. Rack it and tell me if it resets
What kit is that ?
P80 Glock 19 with Recover 20/20 Brace and Holosun 507C reflex sight
Oh and I run it with a suppressor generally I have a Stamp for it
Looks almost like a sub machine
@@Pay_Cinco Thanks look at my Music Maker video. It’s only 1.5 mins
Edit for: 🖕 CNN !!! 🖕
Also, round off the plunger and make sure the extra material is cut out really good in your dust cover where the recoil spring channel is in your P80.
That's always a big issue.
Great vid 👍
who has good after market rails
Rails for what platform
@@JARG pf940 sc
@@stephensmith9334 for you internals?
What is wrong with yours?
@@JARG nothing frame shipped without rails or pins
I need help, tried all things you listed.
What is going on with your piece?
@@JARG trigger fails to reset after firing 2-3 rounds. Is not the slide. I have a zev complete trigger and zev complete upper parts kit
@@MrRomero.A what lbs firing pin spring
@@JARG it came with the zev kit, I believe it is a 4lb although zev doesn’t specify
@@MrRomero.A Recommend 5 lbs minimum. When it does not reset does the firing pin stay back or go over the crossbar
I THINK THE MORAL OF THE STORY IS USE GLOCKT STOCK PARTS
You must be a wizard
@@JARG Nope, just a cheapskate that tried cheap aftermarket parts that stock pars resolved, lesson learned
M ppl
Hey man I just uploaded my video can u check it out and tell me what I did wrong with my trigger please!
Going into meeting. Will look after
Looks like your trigger safety is blocking the trigger
I need your help on troubleshooting my 43 is therea away I can get your email or something else so I can send you videos of the issue I’m having?
justaregularguy21@gmail.com
You can post it to your channel and send me the link
Don’t heat up the cross bar. It’s not needed and bad advice to give because someone is going to ruin the heat treat on their cross bar.
Sir I clearly state Do need over heat…. If you don’t like the advice then keep scrolling
@@JARG but you don’t need heat at all to adjust the cross bar for sear engagement. Sooooo yeah it’s bad advice. The entire trigger bar is essentially a giant spring. Heat destroys springs. Last thing we need is to advise people to heat up their trigger bar potentially ruining the heat treat with a heat gun for example and eventually having a negligent discharge. Sorry but my recommendation is correct and better practice. Sorry you got so fucking butt hurt about it pussy haha. Jesus Christ…take some constructive criticism…essentially around ohhh I don’t know…the fucking structural integrity of a fucking trigger maybe? Douchebag haha