I’m putting a 2002 cab on my 2000 only think I questioned being different besides the way mileage is read is the way the plugs come through the fire wall anyone dealt with going round to square
Can you do an in-depth in the 4x4 control switch i need to replace mine in my 04 f250 and if u can show me how that works it’ll save me from breaking what doesnt need ti be replaced
How far will the dash rotate foward without unplugging everything? I'm wanting to sound deaden my firewall for engine noise but I don't really want to have to remove entire dash.
With the amount of time you're going to put into getting the dash out far enough to try to put sound deadening material behind it, you are better off just spending the extra 5 to 10 minutes getting everything done enough to just pull the dash out. It's going to be more of a pain in the ass to try to work around the dash. Plus, unless you're going to remove the HVAC system (A/C and heater duct box assembly behind the dash), then it's not going to do you any good to put sound deadening material in it anyway. You need to get the HVAC system out so you can put the material directly on the firewall AND put it on the ENTIRE firewall. It won't really do much good to just do small patches here and there. If you're going to spend the time to try to remove the dash part way, just don't bother and save your money because it won't be worth it. Just spend the time doing the job right so you'll be happy. Besides, it won't cost you much more to do it this way. Although you would have to spend money to have someone properly remove your A/C refrigerant and then spend money to have it recharged again, it would be better this way if you want to really get the noise out. I'm not going to suggest the alternative to having your A/C system properly reclaimed and recharged and you can look that information up yourself. I don't want the EPA breathing down your neck. But you "can" do it yourself and recharge the system for the cost of about 3 or 4 cans of refrigerant from Walmart (about $25 to $30).
@@eldridge201 i really want to do it properly, i have my entire cab deadened with extra thick rubber mats on the floor and back panel. Road noise is almost nothing, its great. Now i just need to get behind the dash so i can cut out some of the engine noise.
@@conFIGuredAPK Well, like I typed previously, just spend the time and do it right once. No sense spending a few hours trying to do a "patch" job around the HVAC ductwork or unit when you could spend a little more time and money having it removed and do it right. That's just me though. You can obviously do whatever you want but I just think it's pointless to do a "half-assed" job which is what it sounds like you would be doing.
fred dubose Well it depends on how much electrical work you want to do. Excursions stock dashes went till 05. Newest you can swap in would be 2016. It’s all a matter of how much work you want to do and wiring. 08-10 is a lot easier and cheaper than the luxury 6.7 dashes
I literally just want to take the dash pad out of my old truck for my excursion since before I got it someone either had a oops or got bored and shot through the glove box
This video allowed me to remove a dead rat stuck in the dash after my truck had sat thank you
Man, you saved me a massive headache with this video.
It's awesome,
Thank you!!
This is all pretty helpful to make sure I’m not missing anything. Thank you good sir
Very well put together video. Great job on capturing everything to do and talking on topic. Nice work
get to the fucking point
GREAT video, sir. Well done & thank you!!
G
Excellent straight forward instructions and footage. Thanks!
Very helpful video doing a cab swap this winter and planning on reusing the dash in my existing truck. So that would be very helpful
Thank you so much dude 🙏🏼 dropped something in the defrost vents and finally was able to get it out. Can’t fucking thank you enough
Was it legal
@@stacy.spennyit’s not illegal to drop stuff into the vents, yo. It just happens sometimes! ;-)
I’m putting a 2002 cab on my 2000 only think I questioned being different besides the way mileage is read is the way the plugs come through the fire wall anyone dealt with going round to square
Nice video. Is the hvac any different from an 02 to an 04?
Can you do an in-depth in the 4x4 control switch i need to replace mine in my 04 f250 and if u can show me how that works it’ll save me from breaking what doesnt need ti be replaced
Bro!!! When you touched the antenna plug what the hell was that... looked like it had a tail 😳
I’m trying to do my 97f150 single can into a king ranch let’s see how it goes
How far will the dash rotate foward without unplugging everything? I'm wanting to sound deaden my firewall for engine noise but I don't really want to have to remove entire dash.
Probably 2 feet before it starts tugging on everything. At the point just take the dash out for the extra 7-8 ish plugs.
With the amount of time you're going to put into getting the dash out far enough to try to put sound deadening material behind it, you are better off just spending the extra 5 to 10 minutes getting everything done enough to just pull the dash out.
It's going to be more of a pain in the ass to try to work around the dash.
Plus, unless you're going to remove the HVAC system (A/C and heater duct box assembly behind the dash), then it's not going to do you any good to put sound deadening material in it anyway.
You need to get the HVAC system out so you can put the material directly on the firewall AND put it on the ENTIRE firewall. It won't really do much good to just do small patches here and there.
If you're going to spend the time to try to remove the dash part way, just don't bother and save your money because it won't be worth it.
Just spend the time doing the job right so you'll be happy.
Besides, it won't cost you much more to do it this way. Although you would have to spend money to have someone properly remove your A/C refrigerant and then spend money to have it recharged again, it would be better this way if you want to really get the noise out.
I'm not going to suggest the alternative to having your A/C system properly reclaimed and recharged and you can look that information up yourself. I don't want the EPA breathing down your neck. But you "can" do it yourself and recharge the system for the cost of about 3 or 4 cans of refrigerant from Walmart (about $25 to $30).
@@eldridge201 i really want to do it properly, i have my entire cab deadened with extra thick rubber mats on the floor and back panel. Road noise is almost nothing, its great. Now i just need to get behind the dash so i can cut out some of the engine noise.
@@conFIGuredAPK Well, like I typed previously, just spend the time and do it right once.
No sense spending a few hours trying to do a "patch" job around the HVAC ductwork or unit when you could spend a little more time and money having it removed and do it right.
That's just me though. You can obviously do whatever you want but I just think it's pointless to do a "half-assed" job which is what it sounds like you would be doing.
@@eldridge201 don't know I make it sound like I'm gonna do a half assed job but ok. Thanks for the info
Gracias por el video 🙏🏻 me ayudo mucho
Can you use an expedition dash on a super duty truck?
Super duty would be: f250 and up as well as the excursion. Expedition dash will fit in an f150 though 😊
What tools did you use
Thanks
Question. Wat is the newest dashboard I can put in my 2003 Ford excursion?
fred dubose Well it depends on how much electrical work you want to do. Excursions stock dashes went till 05. Newest you can swap in would be 2016. It’s all a matter of how much work you want to do and wiring. 08-10 is a lot easier and cheaper than the luxury 6.7 dashes
Definitely unplug both batteries before starting tho.
Is this the same of 05-07 I know your title says 99-04 but there is no videos I can find anywhere on 05-07
Did you ever find a answer ?
@@iceweedman nope
How can i contact u.id like a dash and front clip swap
I literally just want to take the dash pad out of my old truck for my excursion since before I got it someone either had a oops or got bored and shot through the glove box
I'll be taking the glovebox too but it blew a hole in the dash pad and door panel also.
👍🏾
How much would it cost to pay someone to change it out
G Paul Welch I’m not sure. Might have to ask around and get a quote from someone
@@Jimmyziggy what's a guess at it