Honda Motorcycle Carburetor Cleaning
ฝัง
- เผยแพร่เมื่อ 10 ก.ค. 2024
- DIY Cleaning a Honda Motorcycle Carburetor with Mercury marine PowerTune , and Honda Carburetor and Combustion Chamber Cleaner.
And a word on JIS Cross screwdrivers and screws.
How to.
#jis #honda #motorcycle #carburetor #howto #diy #snocrushr
Get JIS screwdrivers here (where I did)
www.vesseltools.com/
DIY How to - แนวปฏิบัติและการใช้ชีวิต
![[Full Episode] MasterChef Junior Thailand มาสเตอร์เชฟ จูเนียร์ ประเทศไทย Season 3 Episode 5](http://i.ytimg.com/vi/g5wpgeAIzMs/mqdefault.jpg)
Thanks snocrushr. All around best video out there for my dirty Rebel 250 carb. Sat for almost 2 years, didn't drain the bowl, didn't add Sta-Bil. Started, but only idled rough with the choke half way all the time. Took it apart, cleaned everything with new Gumout spray. Thought I cleaned the jets and enrichment valve, put it back in, but it only improved a little.
Second time through: Reviewed your video and realized idle jet was still TOTALLY plugged. Found the right size copper wire and poked out a load of dirt - not varnish - this was some kind of corrosion. More cleaner, blew everything out with the compressor, back together, started right up and runs like new.
So listen to this video! If you're not sure about the jets and emulsion tubes, buy new ones. Drain your bowl if you're not riding for a while. And ride more!
Glad you found it of some use, cheers and ride safe.
I cleaned the CBR125 carburetor with White spirit/Naphtha from the Drugstore and a brass brush in a bowl. And works fine too. Looks and work like new, no special cleaner required.
I love how step one is get a drink of your choice...Newcastle brown...top choice. lol love it.
If for no other reason than the explanation of a JIS screwdriver, it’s a good video to watch. Thanks!
Good pointer on the screw heads. I stripped a couple before I learned that there was a difference. Nice job, take care
+Rusty “rustyglovebox” Glovebox Thanks for stopping by.
Sweet video Greg! Awesome tip on the JIS screws.
+tomswonderfulworld Thanks Tom
Thank you for this. My '95 Honda XL 250 was missing and jerky when applying throttle and I thought it needed a carb cleaning. First I checked the spark plug, totally carboned up, then the air filter - filthy. I replaced those and it's running great now. Smooth acceleration through the entire power band. It's got 53,000km on it so maybe a carb cleaning like this will help too. I'm not convinced I can do it yet!
I thought you were going to clean it in beer there at the start and I would of had to give you heck on that LoL. Great tip on the jis screw driver sir.
+Cheator40 No I keep my carb cleaner and beer separate...although I'm sure I've had some beer that tastes like carb cleaner 😜
Great video and awesome instruction on how to clean the carburetor it came out really clean.
Informative! I have overlooked the JIS screwdrivers in the past... poor bolts.. Thanks!
+Daniel Noest Thanks for watching.
I learned something new. Thanks!
Nice work. Thanks for sharing!
+CT moog Thanks for watchin'
After I cleaned my Carb I Chrome Polished my CRF Carb for shits and Giggles and it came out like a Mirror. Thank You Dremel
Yesss mate! Love the drink👌🏼, my home town Newcastle, Gateshead! Great video btw
good video !
the 1st 45 seconds & it got my approval and I ain't even seen the rest 😅🤘
Wow, being from Newcastle myself I never expected Americans to be drinking that stuff! Nice one, I've had many a drunken night from that stuff
That's because I'm an Canadian 😀
1:22 at last someone knows what screwdriver to use... Well done.
Just spent a bunch of time rebuilding my xr100r carb...before service bike would barely start or stay running, I cleaned everything, jets, bowl, the whole nine, now it starts right up and ldles,but you hit the throttle to excel and it spits and pops...is the float supposed to be set "level" when held upside down with the bowl off.?"my float was sagging down, my bottom outside screw is 2 1/4 turns out. Now what?
I tapped the JIS cross-head screws with a small hammer to loosen them up and they came out fine with a PZ1 screwdriver & body weight (CMX250).
Good video Sir! My Shadow has a gummed up carb. This info will be quite handy and is very timely. Take care, be safe!
+Ironheart Fabrication Thanks JE
Love the tasty beverage of choice! Long live the Ale!!
Great little posting... was quite anxious about taking apart my bike to clean the carburetor but like a parent after their second or third child, I am much less worried about 'hurting' the bike. :0) Like the Newcastle but have you tried any of the Scottish Highland beer? Cheers...and thanks. :0)
Very well done , I would have used a Phipps driver and bodged it up. LOL
+STEVE ROB I've bodged a few in my day....before I learned of JIS.
Did you take any protection using these dangerous spays during drinking beer?
Had to watch it again to see your hashtags sir.
" its the inside that makes the difference " 7:10 ... deep..
informative video, we use to boil carb in hot water. ,worked well.
+finpainter1 Carb soup...Haha
good
How to service brek
Sir can you. Guide me about stock maain jet and slow jet of honda cd200
Sorry that model was not released in North America so I have no information on it.
sir can u pls guide me how to clean the carb of suzuki Raider R150?
rockzen rage raider 150 is not available in the US.
Nice we're can you get JIS screw driver
Link In the description.
Good video
+wtbm123 Thanks Terry.
in my experience, regular old carb & choke cleaner will badly distort the float bowl o-rings. for that reason, i have never used it on the rubber-tipped float needles. i noticed that you tossed the float needle right into your combustion chamber cleaner so i guess you have found that it doesn't damage those at all ? by the way, thanks for spreading the gospel re: JIS screws and screwdrivers.
I knew that he would know what he’s talking about by cracking open a brew before he works
ေကာင်းတယ်
loved it....just sub to your channel...
I used CLR in the past and it worked good
I've used PowerTune for over 30 years now. I also tried some others but kept coming back to an old faithful.
Coor's light im working on a cb125 79
Newky Brown Ale :-)
And the model of carburetor in cd200 honda . which one I use from these pz30 ,pz26 or pz27 ?
pz26 is for 125cc engine
pz27 is for 150cc and pz30 is using for 175-200-250cc engine
Bang Nguyen thanks mate
malik gee
sante!!!
First step is key
Didn't know about jis
+Buckswoodshop I was unaware of JIS for many years myself
snocrushr 465759568
Newcastle Brown Ale give that man another can...
im so scared of not knowing how to put everything back together
Graham Bikes it's not as bad as you think record it well it's being taking apart and review it if you get stuck
Fernie Rodriguez I took it a part I found out why I was leaking out of my drain tube it’s because my floats were bent and there for not floating got a rebuild kit otw!
The problem is if something surprisingly come off, above all that components linked to springs, it would be a nightmare trying to find out how they were originally and you may end ip taking all the mess to the mechanic lol 😆
youjis
good vid but you skipped taking out the oran washer and clip !