ฝัง
- เผยแพร่เมื่อ 3 มิ.ย. 2017
- I have tried and tried and tried.
I can no longer say that i know what to do anymore.
If you search around TH-cam for this speedometer, you will find nothing helpful.
I get the speedometer to function although i cannot change the parameters for the wheel size so it constantly miss shows my speed.
I have also changed the possition of the magnets provided for me, with 3, 2 and 1 magnet and change the changable parameters in the little menu that i am able to enter.
Engine revolutions is impossible ( meaning that i am not smart enough to know what to do to get it to show revolutions on the speedometer ).
Anyone that may not have figured it out, you need to put the odometer onto the trip function and then hold down the left button to get into the menu...it will ask for id which is supposed to be 750 as default and then hold left button again and it will go to tire circumference and then hold left again to get to pulses for speed sensor and then to factor which i assume is engine stroke? Dont know about last one though
I think I have some answers for you. The tachometer signal has to be negative going pulses. Mine starts showing rpm's when the signal is -2 volts. I've taken it all the way down to -15v without problems. I suspect the input impedance is on the order of 10KΩ so it doesn't take much of a signal to drive it. It also works fine is the pulse train goes plus and minus. From my calculations the tach will read correctly if there is a pulse for every revolution of the engine. i.e. 167Hz = 10,000 rpm.
You figured out how to get into the circumference settings by being in the b-L display mode and pushing both the SEL and SET buttons for 3 seconds and releasing them. I think the 4 digit number is the circumference in mm. If your tire is more than 2999mm, then add a second magnet to the opposite side and set the circumference value to half of the actual value. Be aware that the speed sensor will not sense the magnet if the wrong pole is towards the magnet. You can test which side of the magnet should face the sensor by waving the magnet in front of the sensor while watching the speed display on the unit.
You're right! There are many variants of this universal meter speedometer out there! They all look the same and basically work the same, but there seem to be several firmware versions that all use different methods of getting into the settings menus / setting parameters. It's frustrating!
i have the same Speedo, i need to instal 4 magnet on wheel for have good speed indication, and with set wheel circle on b-l menu (avg 1800 for 110/50 17)
do you think tachometer would work on a magneto style ignition, that mopeds use?
I know it's an old video but just thought I'd try to help others I've spent most of the day with the same issue and finally figured it out for some reason it won't let you enter the menu to set up wheel size and other settings etc when you have your permanent live memory wire connected! You have to disconnected the permanent live memory wire, then hold the left button down and turn ignition on then the menu will appear once set up connect back up your permanent live before switching ignition off,
I appreciate the help anyways mate! Cheers👍
@Paul Stacy thanks for this comment i will try. May i ask what is the color of that live wire?
Thank you man is very importand video because like you sed the other videos about this speedometer is in Chinesse language. Thanks to all of you guys for the answers.
I had the same issue on my Reiju. had to use a wheel size calculator to get the right digits to input in the menu to enable the speedometer to calculate the correct speed readings.
Can you send a list from the color of the kabels? I dont now wich cabel gos to rpm or something.
Try press and hold then open the ignition. I have the same speedo and its working . The red and black wires. One of them is + direct to the. Battey . And the other is on the ignition lock. And theres a setting there for the rpm if - or + your rpm signal is .speed sensor and fuel gauage.
Apologies if this is a stupid question, but what advantage do these speedos have over the stock speedo that comes with your bike?
none at all! exept that my original speedometer was totally toast, AND the parts needed to fix it was way to expensive, so i started to search for cheaper alternatives :)
Also problems with this.
Speedometer hall sensor does not work.
I do not know if the problem lies on the cockpit or on the sensor.
Does anyone know if this can be measured?
What voltage is generated between the speedsensor signal + and signal -?
What is the output signal?
Cockpit wire connection:
Black/white: sensor signal
Green: sensor signal negative
Yellow: sensor positive
The cockpit works very well. Only my speedometer gives problems.
Thx
Long as powered and it tells me speed .. wasn't bothered about rest of It, so didn't connect it .. happy enough at that
Hi, can someone let me know the position of the wires in the plug? Sometimes, here's the problem. The wires can be swapped in the sensor plug.
On the instrument itself, the following wires are provided:
Yellow = speed sensor plus
Green = speed sensor minus
Black = Speedsensor signal
Is this also with you ??
Digitronix BE have you watched project next he mite be able to help you with what you need to no as in the wiring programming if it helps
I found the solution for this model. You have to be switch off then you must have pressed the left button and switch on the key at the same time. You must continue to press the button until the demo stop and you will be at settings menu. It's a little tricky and i had headache until i figure out
To access in the menu, turn off the key, press de "del botón" and turn on the key, when the speedometer is on left de botón sel
Thanks for all the replies guys👍 appreciate it 😊
hello, how did you manage to get inside the menu to select the wheel size and calibrate the speedometer, i can t get to the menu to reset it and the speed is not real al the momment. cheers
@@valentincosmin4391 you need to press the left side botton 4sec before turning the whole system on, you can access the whole calibration after you done that
hey how did you get the gear indicator wired up
The RPM is wired to the signal pulse from the stator pickup, tap into that lead at the CDI unit.
Shane Thans do believe me, i have surely tried...
MANY times, i tried takling the site around each and one of the spark plug cables, and got a signal! But it ruined the LCD display, and now i bought a New one👍
i have the same Dashboard you have sir, i install it on my underbone motorcycle, for the speedometer calibration, you need to turn off your key then hold the left side botton 4sec before turning the key on, it will show the first 3 digits which is for speedometer, the 4th one is for the Rpm calibration then the last is for fuel level maybe, for the RPM sensor, you need to use the yellow/blue wire then tap in either from the pulser(blue/white) on the stator or the charging wire(white wire)also in stator, i wasted whole day just to figure everything out especially that damn fuel gauge
hi sir did you manage to make the fuel gauge work? may stock gauge has three wires for fuel, i dont know how to connect it here thank you in advance.
@@janeaustria5257 you just need one wire from the whole tank assembly, if I'm not mistaken its colored Blue/white, you need to disregard the other two wires, and also that blue/white wire corresponds to blue/white wire at the dashboard assembly
Can you use it on scooter? Like aerox or smth.. ? Because i have stage 6 sport handleabar, and i need a speedometer, and odometer, so can i use it on my scooter?
hello Nojus.
i guess you could? i have seen several using the speedometer on their mopeds, such as Yamaha DT 50 and such, as long as you hook the RPM wire around the coil cable going to you're Spark plugs.
put the odometer on the front or back wheel, does not matter as long as you get the correct dimensions on the wheel, inside the menu :)
Good luck, man.
high five!
Can you set the odometer to the current miles on OEM dash?
Hello! Not that i know of 🙈
The rpm works with a positive signal. You have to connect it to the trigger of the CDI
Iván Barton i tried to do that but it still malfunctions quite badly
@@thatdude5477 You need to choose the right settings for the pulse .
Ex. 1 pulse per 1 revolution (1P1R) 1 spark per 1 rpm of the crankshaft (usually for 1 cylinder 2 stroke bikes/ for 1 cyl 4T bike it will be 2pulse1rpm). You need to figure out what is the spark mechanism of your bike by knowing how many cylinders you have and if its a 2 stroke or a 4 stroke
One of the wire is need to be connected at one of the terminal of the ignition coil. That how the rpm gauge work. Speedometer sensor is nothing to do with the rpm gauge.
Hold the left boton for 10 sec and turn on the ignition and you will go to its settings, I have the same speedometer
the wire that signals the coil to fire is the one you hhok to tach wire
Would this work with 84 Honda magna v30
Fernando Rivera
Probably?
This is on a suzuki gsx 750 es from 1986
hasta ahi bien. ¿como se accede al menu para poner señal positiva P o negativa N para que capte RPM. tengo que acceder a ese menu para que capte RPM
Could you put this on a 2006 drz 250? Has a mechanical trip meter?
Yes you can! it will fit motorcycles with 1 to 4 cylinders👍
I will help you with the menu ...
How ?
As far as the gear selector go's, your bikes old cluster had to have that feature before, you cant just add it because there won't be a cable for it.
Hello! Yes i am aware of that 🙂 luckily the old Gsx 750 ES have the gearindicator from factory 🙂👍
How accurate is the speedometer on speed?
Michael Bartlett it is actualy not too bad taken in consideration that it costed me like 25$. 😐
maaaaan,i have exact same situation.I did the same things over 100 times)))And what i got? Nothing!)
Found out that this is a bad copy of an copy of an copy of the original one.... i am terribly sorry to tell you this my friend,
so i ended up buying a different kind of Digital speedometer. gonna try that instead. hope you get it working dude!
Dude do you have an english translated copy of the wireing, i just bought the thing and its all writen in a language i dont have
Hey, you should on om the Banggood app and find it there👍 although the english isn't very good😂
@@thatdude5477 All good man i went to a Chinese restaurant and got a meal there.....oh yeah and they translated it
@@saltymedpac3943 awesome 😂👍
How do you manage to make the fuel indicator works?
The fuel meter works by sensing resistance between the fuel sense line and common / battery negative. Full is 6Ω to 10Ω, Empty is > 90Ω. It basically uses a 100Ω linear potentiometer connected to a float inside your fuel tank.
Same question, I have a 3 wire sending unit on my tank, ground, blue/why and yellow/blk - only 1 wire for the signal on the display, how do you wire this?
If it's a resistive sending unit, use an ohm meter to measure from your ground wire to the other two wires. If you're lucky, the highest reading will be about 100Ω. Next, if your tank is more than half full, find the wire combination that is less that 50Ω. If it's less than half full, find the combination that reads more than 50Ω. One wire goes to GND and the other goes to the yel/wht wire on the meter.
@@Fourcycle hello sir, i have 3 wires on my fuel gauge as well, do i connect the two wires to my new cluster which has only 1 wire, and tap the ground wire to ground? thank you in advance
@@janeaustria5257 I already explained it above. Do some research on potentiometers if you don't understand.
On your bike where you plugged in the tachometer wire
I tapped into the signal pulse on the cdi - the lead that comes from the pickup on the stator
Is it possible to set the total mileage?
Dmitrijs Nikitins hey man.
Not that i know of?
Do you want the total milage from the original speedometer to also be Seen in the digital speedometer?
Then you would have to take the magnet on å small spinning disk with the magnet on it, and run it the total milage by "hand".
Hope this gave you an answer :) high five!✋
I was wondering the same thing. I think I'm going to put the magnet on a high-speed grinder and just run that thing as fast as I can
Hi how did you get the speed to show because mine just shows 0
Speedo Junkye
Hey Dude!
Have you placed the magnets correctly according to the sensor? Theres North and South poles 😉 and keep the distance between magnet and sensor at aprox. 1 MM i found the best reading.
That Dude Well the sensor is facing the magnets with magnets little circle inside the casing facing the sensor if you know what i mean, Is that the wrong way around? Otherwise magnets are defo 1mm apart in distance to sensor
Speedo Junkye hey dude.
Try to take one of the magnets off, and the sensor aswell, switch the magnet rapidly in front of the sensor (Both sides of the magnet) and try to see if you can get a reading? If you get a reading, try to either put in 3 magnets, as i did, download GPS speedometer, and change the numbers inside the speedometer to match youre speed. Mine is showing 10km/h more than ny real speed, but i left it like that pusposly
That Dude Will try that in a bit. I acctualy didnt fit few wires from the speedo, but I doubt that should make a difference, Didnt plug 2 round heads(dont even know what they are) coming from speedo seperately, fuel line, oil line, and no gears just hooked N up.
That Dude Ye its still not working on either side of the magnet... Ive 2 magnets in total tried many sizes of wheels still 0. any ideas? The support crew are helpess they just ask for a video but what am i gonna show them...
I know this is old and others have said. but you have to hold the left button and then turn on the ignition.
Thanks mate! i know this will be helpful for allot of the other people in this chat :) realy apreciate it :)
@@thatdude5477 i now have a problem with mine though where it wont turn on everything until i plug and unplug a connector. just the neutral light comes on
The numbers are the diameter of ur tire/rim in mm
Can only see a strip up the middle of the screen. You need to sort that out first.
Can I use this in my mopad ?
Koustav Khatua yes you can🤩
@@thatdude5477 thanks bro.
Did someone know how to wire the fuel and rpm wires I need some help
The fuel wires can connect with the cables from you’re tank, RPM wire had to be curled around the spark plug wire
@@thatdude5477 did you know if the fuel need one or two cables.
Some one told me for rpm the wire need to be somwear in ecu
It took me a minute to figure out the tachometer wire. I'm running this on a 1986 Honda VT 500. There's four wires that come off of the spark unit for the spark plugs. There's one on my bike that's bright yellow. Solid yellow. And that is what you need to hook up. It goes to what they call the rotational rate wire. It should be blue and yellow. That's it for the tachometer. I want to know how to shut the gas gauge off because I don't have a gas gauge in my tank. Any input on that?
What is a wideo ?
Good question🤯
What is your motorcycle?
bartha oLg Suzuki GSX 750 ES
@@thatdude5477 cool
How'd you go ? I've figured it out.
hey man, i finally figured it out myself! but i recently sold the bike with the speedo installed, cus i wanted to start on a new project :)
your doing wrong sir. .. just only press sel button for 3 second then on the egnition switch then release. dont steak on pressing the button . once the key is open, release the button.
Still laughing my ass off; your language choice and comments are just brilliant!!! (Ps. Chuck the shi1t in the dustbin and don't buy Chinese again) Have you found and alternative that actually works? I'm looking for one for my 2010 CBR 1000rr, but the internet is not very helpful... Cheers
Hey mate! Glad i can still make people laugh😂👍 yeah i found some alternatives, but ender up selling the bike though! Bought my self a NX650 and have ordered a new type of digital speedometer from china🛵 thanks for the comment, have a good one!
I have the same shit, no RPM, the speed is rong , bought another one , another crap but at least
the speed works, different copy .....
Hahaha funny
It's Impossible to get into the menu , tried everything doesn't work 👹
nigel russell welcome to the gang 😂👍
Ayyy same here lol
You on Instagram or Facebook?
WIDEIDOS, WTF
What?
Sorry I feel for you and anyone that has bought this Chinese fakes. I think among best are Samdo and vapor speed digital meters. The market has been flooded with fakes and unless someone evaluates them and advice us here it's really a terrible con game.
I totally agree with You! I would not advice anyone to buy these chinese speedometers.
STOP SNIFFFFING YUCKKKKKKKKKKKKKK