140K? You just getting started... 🙂 My 07' Si I bought new in 07' now with 281K I left stock is my daily and my 22' Si gets lonely sitting in the garage a lot...stock clutch lasted until around 233K and Starter until around 250K or so. Alternator is still original. No other issues motor and transmission just solid... The car does burn oil so I check and add as needed. Change it regularly around every 5K since new.
@@real_bukla8s345 that platform is SOLID really... I have my doubts with my 22' Si 11th Gen Si EVER reaching that type of mileage (if at all even possible...) with minimal issues...esp. the Turbo.
I actually learned in the 8th gen forums that people put the rear lower motor mount in the freezer so that it shrinks a little bit so that you have more wiggle room to install it!
A little tip for anyone who is under 300whp. Just inject your factory mounts with 80A polyurethane. You can get this from the autoparts store as widow cement. Works absolutely amazing, much cheaper, and not as many vibrations. Took away all my wheel hop at the track on a prep surface. Helped me cut a 2.0 60'
@@johnlong9532 there are gaps to fill up. I tapped a peice of cardboard on one side, and injected it until it couldn't take any more. Flipped it over removed the cardboard, and filled up any airbubbles. A little olive oil on your finger tip, and smooth it out to make it look uniform. Give it at least 24hour to cure, 48hours if you can... Then reinstall, makes an absolutely huge difference.
@@SomeOne-on6yf Got it, thank you for the explanation. I’ll be picking up an 06 FG2 this Sunday and it’ll be nice to not have to worry about wheel hop as much, it was pretty noticeable on my 07 I owned previously. Any other tips in regards to wheel hop and having a good launch in general?
@@johnlong9532 yeah this helped tremendously with wheel hop on the track. You virtually get no wheel hop at all after this mod. And feels better than any aftermarket mounts ive tried
You took my advice and got a dash cam, good job bro. My accident last year January that almost killed me, if it wasn't for my dash camera, I would've been screwed.
Highly under rated mod! I have a 2008 FG2 that tore one of the mounts... It clunked around when shifting hard, or even just stabbing the gas. And I drove on it for a WHILE... So when it finally decided to do a repair, (and I am of the mindset that, if you're going to replace a part, instead of putting the same thing there, put something better!) So I got the whole set of 62A mounts... It felt expensive in that moment, but that all changed once I drove the car. Shifts are crisp and clean. And throttle response is ever so slightly 'sharper'. But what surprised me the most (and something that I wasn't even expecting...) because I got used to the blown mount that would smack around every time I moved from a stop, I didn't realize how it affected the clutch engagment when moving from a stop... However, driving with the new mounts, I instantly noticed that they gave me back a great level of accuracy and clutch feel, resulting smoother and more predictable engagement from a stop. I was amazed at the difference. Not even 15 minutes into my first drive with them, and I no longer had any regrets of spending what I did, these are worth it... Not all mods need to add power to be satisfying. I say the same about my Hybrid shifter... It doesn't add power, but it adds enjoyment.
I drove an 8th daily for 14 years it was my 2nd car ever my first was a 95gsr when I was 16 busted my ass cleaning tables all Summer for that gsr. 3 years later I sold it to get a new 8th Gen. Mine had 50 miles on it when I drove it home. I put 310k miles on it and had changed those motor mounts twice. 😂 and yes my biggest complaint of this whole generation of Hondas was engine bays were way too freaking small!! From the civic, the fit, crvs, and the RSXs. Baby Engine bays! PS my 8th Gen was still firing up strong when I sold her to get a civic sports hatchback. I hit a deer with her a year ago and totaled her. My current daily is my 2023 Civic Si 😎 hondaboiz for life!
Those hasport mounts are amazing for driving 10/10 and beating on the car. However when cold or idling at light it’s like driving a vibrator on wheels. Helps a lot with wheel hop tho.
I have been daily driving a 4dr 8th gen si for about 2.5 yrs now the cars are such a blast with a 6 speed and k20 that I recently acquired another one with a bad motor and a 9th gen si trans. Things escalated quickly and I bought a 2dr si that had major front end damage but original more and trans that way I could swap everything to make my second one a track car like I’ve all wanted. Now I just need a tow rig 😂
Hey John, if you clean those headlights with wax and grease remover then spray with adhesion promoter, let dry then clear coat those headlights, the scratches will disappear .
I ended up going with innovative 75a mounts due to the front mount being included. Vibration is very minimal. It’s a huge difference compared to stock. Shift are much more accurate and the engine doesn’t move at all.
Hey brother just ordered my mounts today thanks to your review on them because the other videos i have seen was not what I was looking for !! And the content is fire!! Just subbed to the channel!!
I don't have hasport mounts but I do have innovative mounts with the same stiffness as your hasports on my EM1 which are pretty equal I think. I've had them for 2 yrs now and I love them but like you said the idle and accelerating is where most of the vibration is but overall Im lovin the upgrade.
So glad I went with 62a for both rear and upper torque mounts as it's my daily.. Rear mount is best installed with the car 'level', on a hoist lol😅 Jacked up front end only force's engine weight to the rear, hindering install..
I just did the rear Hasport mount and it went in pretty easily…. Using the scissor jack to push motor forward against the brace, everything jsut slipped in and out easy…. Most people wrestle the motor and muscle the mount in with a hammer for a while..
@@boosted_john 70A but I only did the upper and lower torque mounts, I left those two larger side mounts stock. I figured majority of the engine movement was from torqueing backwards anyway so that helped out with the vibrations, if it gets annoying with your full mounts I'd recommend at least trying that out!
I'm on my 2nd 8th gen my 1st si had 75a innovative they were great so I went and installed them on my 2nd si as well and they're great I love them but I can't thinking that maybe I should've tried the hassport to compare
Just a fyi it cant send it to china cause it doesnt have access to the internet when you connect to it via wifi you dont have access to the internet you are just connecting with the dashcam itself similar to how bluetooth works with earbuds unless it has cellular capabilities which werent mentioned but then you would need to pay to use the cellular capability using the normal providers like Verizon or t-mobile.
140K? You just getting started... 🙂 My 07' Si I bought new in 07' now with 281K I left stock is my daily and my 22' Si gets lonely sitting in the garage a lot...stock clutch lasted until around 233K and Starter until around 250K or so. Alternator is still original. No other issues motor and transmission just solid... The car does burn oil so I check and add as needed. Change it regularly around every 5K since new.
I’m at 240k with my FA5 and just got new speakers and sub all around and the real only mechanical issues so far were my water pump and cmc and slave 👍
Since I been running royal purple motor oil on my SI, it has drastically reduced oil consumption. Give it a shot.
@@real_bukla8s345 that platform is SOLID really... I have my doubts with my 22' Si 11th Gen Si EVER reaching that type of mileage (if at all even possible...) with minimal issues...esp. the Turbo.
@@powerbybeans7389 Really what is your mileage? Thanks!
@@edwardinvegas just kswap it and reliability shoots up 200%, along with reduced labor costs 😂
I actually learned in the 8th gen forums that people put the rear lower motor mount in the freezer so that it shrinks a little bit so that you have more wiggle room to install it!
Great advice!
A little tip for anyone who is under 300whp. Just inject your factory mounts with 80A polyurethane. You can get this from the autoparts store as widow cement. Works absolutely amazing, much cheaper, and not as many vibrations.
Took away all my wheel hop at the track on a prep surface. Helped me cut a 2.0 60'
What exactly do you mean when you say inject? Are the stock mounts hollow and you can literally use a syringe to inject the polyurethane?
@@johnlong9532 there are gaps to fill up.
I tapped a peice of cardboard on one side, and injected it until it couldn't take any more. Flipped it over removed the cardboard, and filled up any airbubbles.
A little olive oil on your finger tip, and smooth it out to make it look uniform.
Give it at least 24hour to cure, 48hours if you can...
Then reinstall, makes an absolutely huge difference.
@@johnlong9532 you can use the 80A polyurethane they use to attach the front window.
@@SomeOne-on6yf Got it, thank you for the explanation. I’ll be picking up an 06 FG2 this Sunday and it’ll be nice to not have to worry about wheel hop as much, it was pretty noticeable on my 07 I owned previously. Any other tips in regards to wheel hop and having a good launch in general?
@@johnlong9532 yeah this helped tremendously with wheel hop on the track. You virtually get no wheel hop at all after this mod. And feels better than any aftermarket mounts ive tried
You took my advice and got a dash cam, good job bro. My accident last year January that almost killed me, if it wasn't for my dash camera, I would've been screwed.
Highly under rated mod! I have a 2008 FG2 that tore one of the mounts... It clunked around when shifting hard, or even just stabbing the gas. And I drove on it for a WHILE... So when it finally decided to do a repair, (and I am of the mindset that, if you're going to replace a part, instead of putting the same thing there, put something better!) So I got the whole set of 62A mounts... It felt expensive in that moment, but that all changed once I drove the car. Shifts are crisp and clean. And throttle response is ever so slightly 'sharper'. But what surprised me the most (and something that I wasn't even expecting...) because I got used to the blown mount that would smack around every time I moved from a stop, I didn't realize how it affected the clutch engagment when moving from a stop... However, driving with the new mounts, I instantly noticed that they gave me back a great level of accuracy and clutch feel, resulting smoother and more predictable engagement from a stop. I was amazed at the difference. Not even 15 minutes into my first drive with them, and I no longer had any regrets of spending what I did, these are worth it... Not all mods need to add power to be satisfying. I say the same about my Hybrid shifter... It doesn't add power, but it adds enjoyment.
I drove an 8th daily for 14 years it was my 2nd car ever my first was a 95gsr when I was 16 busted my ass cleaning tables all Summer for that gsr. 3 years later I sold it to get a new 8th Gen. Mine had 50 miles on it when I drove it home. I put 310k miles on it and had changed those motor mounts twice. 😂 and yes my biggest complaint of this whole generation of Hondas was engine bays were way too freaking small!! From the civic, the fit, crvs, and the RSXs. Baby Engine bays! PS my 8th Gen was still firing up strong when I sold her to get a civic sports hatchback. I hit a deer with her a year ago and totaled her. My current daily is my 2023 Civic Si 😎 hondaboiz for life!
Those hasport mounts are amazing for driving 10/10 and beating on the car. However when cold or idling at light it’s like driving a vibrator on wheels. Helps a lot with wheel hop tho.
I have been daily driving a 4dr 8th gen si for about 2.5 yrs now the cars are such a blast with a 6 speed and k20 that I recently acquired another one with a bad motor and a 9th gen si trans. Things escalated quickly and I bought a 2dr si that had major front end damage but original more and trans that way I could swap everything to make my second one a track car like I’ve all wanted. Now I just need a tow rig 😂
Hey John, if you clean those headlights with wax and grease remover then spray with adhesion promoter, let dry then clear coat those headlights, the scratches will disappear .
Thank you for sharing. The reflection on the car of your garage lights are incredible
kinda crazy a sponsor would send you a used product lmaoooo
I ended up going with innovative 75a mounts due to the front mount being included. Vibration is very minimal. It’s a huge difference compared to stock. Shift are much more accurate and the engine doesn’t move at all.
Hey brother just ordered my mounts today thanks to your review on them because the other videos i have seen was not what I was looking for !! And the content is fire!! Just subbed to the channel!!
Welcome to the channel bro! Glad I could help 💪
You should have put grease on the motor mount rubber, it makes it easier to slide in.
I don't have hasport mounts but I do have innovative mounts with the same stiffness as your hasports on my EM1 which are pretty equal I think. I've had them for 2 yrs now and I love them but like you said the idle and accelerating is where most of the vibration is but overall Im lovin the upgrade.
Because you have one of the best shifters out there for sure
Should of jacked up the engine for lower rear mount
So glad I went with 62a for both rear and upper torque mounts as it's my daily..
Rear mount is best installed with the car 'level', on a hoist lol😅
Jacked up front end only force's engine weight to the rear, hindering install..
Let’s race!!
Good stuff John, i plan on getting out to some track days this year. Hope to see you out there
I got the Boomba ones and they’ve been great for the price. They don’t include the side mounts but I don’t know how important that really is
I just did the rear Hasport mount and it went in pretty easily…. Using the scissor jack to push motor forward against the brace, everything jsut slipped in and out easy…. Most people wrestle the motor and muscle the mount in with a hammer for a while..
Loved my Hasport mounts! Great mod for sure
We’re you running 62A or 70A?
@@boosted_john 70A but I only did the upper and lower torque mounts, I left those two larger side mounts stock. I figured majority of the engine movement was from torqueing backwards anyway so that helped out with the vibrations, if it gets annoying with your full mounts I'd recommend at least trying that out!
Definitely makes me glad that that lower torque mount is much easier in my 9th gen lol.... 😅
John that 6th Gen Coupe is beautiful. I miss the one I had.
Your reviews are perfect bro very descriptive..
Id be paranoid 100p with that dash cam lol great video as always.
Bro they’re listening 😳
@boosted_john I mean only in minecraft my bad
I would have gone with the billet 6061 hasport Race engine mounts
The k swap out my hatch came from a 06 si had 260k miles it currently made 620hp on a turbo never opened lol
i need mounts soon Lol, feel my engine jitter too when it’s cold
I'm on my 2nd 8th gen my 1st si had 75a innovative they were great so I went and installed them on my 2nd si as well and they're great I love them but I can't thinking that maybe I should've tried the hassport to compare
No tint? Do u plan on selling the car soon? Or prefer no tint
tint cop grabber im ok
What stereo do you have installed your 8th gen and do you recommend it. Tryna change my stock radio
Just a fyi it cant send it to china cause it doesnt have access to the internet when you connect to it via wifi you dont have access to the internet you are just connecting with the dashcam itself similar to how bluetooth works with earbuds unless it has cellular capabilities which werent mentioned but then you would need to pay to use the cellular capability using the normal providers like Verizon or t-mobile.
same thing happened with crossthreaded bolts to me on my rear knuckle in my st car was down for 5 days:(
What radio is that. Does it have car play ?
70A mounts kind of vibrate too harsh for me tbh
Especially when taking off lol and freeway usage
My homie has em in his 8th gen si
Yeah man, I generally have a pretty high tolerance for car induced pain. I hear ya though. Probably too aggressive for some. Perfect for others.
johnny went from nice clean hands with gloves to fck this sht, lemme get down n dirty lolol
Yoo just wondering what kind of oil I should use to break in my rebuilt b20v? For break in and also after. Thanks!!
I just always run conventional 10w-30
Ngl #novlight is actually really reliable and bright asf. No sponsor
I crushed my finger also and the top of my hand. Doing brake pads on my mate golf gti. ✌🏻🇳🇱
Rip.
I put it in sideways easily 5:18
What happened to the k24 civic giveaway?
More info coming soon.
Good stuff
Dingdongdrift??? Wheres prizzamike😂😂
That rear mount is the worst haha
how tf am i sitting in my 8th gen with the exact same fbrown flanel on rn? 😂
I hope your finger is okay. LY❤
All better haha.
lol I already did all of those! Good video though.
❤
No idea how I got here but I have an 8th gen si sedan
Welcome!
Just subbed great content man! Help me mod mine please hehe jk i'll be learning from you.
Just water sand old clear and re clear and water sand don’t this on few cars
Why would it be named something "American" when it's made in China lol
bro have you met prizza mike? hes done a video with DingDong, yall should colab🫣
Mike and I are gonna turn John into a drift rat
I’m in
@@boosted_john you're gonna need one of the rwd johnies
yes broo, ive got an 07 si and she may or may not be whipped occasionally 😅
@@boosted_john drift s2k? 👀