You people are ridiculous. You just worry about a weld. The EPA should be going to every location and shutting every shop down every muffler shop and putting the owner in jail for it because they know it’s illegal they should not be doing it it’s tampering with federal emissions.
When using the cutting wheel, you and those nearby need to wear a full face shield. When welding, use a welding mask. When painting, use a respirator intended for painting. Be safe because injuries suck!
I can’t stand people when they take the cutting guards off of grinders because they can’t get close enough to it. Use a different Saul or put a new blade on it. They want to run it all the way down to nothing there is a reason why it only cut to a certain point it is call safety.
The _"I literally have no idea what im doing"_ was surprisingly reassuring since after seeing a fellow practitioner of the bruteforce method it sparked great confidence in me after realizing i wanted a catdelete this morning. The go with the flow figure it out along the way is severely underappreciated and has always served me well. most of the time. Sorta. 80% of the time it worked every time so the odds are in my favor imma just go for it
@Guitargreat right..who hired him?does not even know what a sawl zahl is just waiting to see him cut off a finger..i dont know some people just SHOULD NOT do certain things.
This man was staring straight at the welding😂 I hope you can still see. Also you’ve gotta be a lot more careful with the grinding disc I’ve known quite a few people to have to go to the hospital holding them like that
you should have removed the cat with a wrench at the flanges then straightpiped flange to flange so that you can reinstall the unused cat for smog and it doesnt show any signs of modification
How does this affect the vehicle performance now that there is very little back pressure? I've heard mechanics say cats are necessary because they provide back pressure for the correct HP.
The vehicle will actually need to be tuned now for adequate performance as more air flows you need more fuel to mix otherwise it sounds like sh!t like this car and you will actually lose performance. All in all it works amazingly when done properly and with the help of someone that can adjust fuel injection rates. Otherwise you are wasting your time. Also if you move sensors around a bit you will still pass any inspection and wont throw codes. This was kinda a backyard DIY vid it seems.
You really need to get into another line of work. You have no concern of your own safety and well being. Use some common sense ,you only get one set of eyes in this lifetime.
He just wet behind the ear. Just cause he's green don't mean he should stop. I am sure he's researched, studied, and experience more in this field of work.
After seeing this video I learned how to fix the car THE WRONG WAY! 1st u need to use gloves not the ones you stole from dentist 2nd cut the cat off between the mounting flanges ( pre bend pipe if needed before starting the project 3rd is practice welding on the ground 1st 4th wear a welding helmet, even if u just spot the 2 metals without a shield u will feel your eyes burning later Just think safety 1st And you need to do a before and after sound of exhaust so that people can hear if the modification will make a diffrence on there car
VZ And you need to do a comparison of your spelling and the difference between there and their before and after an English course, grade 5 or 6 I believe!
I just had a pipe welded onto my Ford Taurus se.The guy said he was gonna gut the other two I believe. Now it runs a little loud while idling. But my speed is back up.
it could be that your cats were clogged just like mine so it sounded like it was normally quite. but now since they are new or deleted you have more air flow which could make it louder.
Take the heat shield off convertor. Cut a small square 3 sided hole in convertor, bend metal back. Take a hammer drill with a chisel adapter, break all the honeycomb out, weld the square shut. Done. This will keep piping all in one piece and much safer.
zip cut blades can blow apart, you should be using a guard and keeping your face out of the blades trajectory path... I never use a guard, only with zipcut blades, man that was stupid.
I have a 2008 Ford Escape Hybrid by removing the catlytic converters do y’all think it would instantly affect the truck’s performance since it’s an electric hubrid??? thank you
@@spiritualangel824 those you would have to buy a new one. If it was just a straight pipe that you can cut from each end then it would be easy. Or you can take it to a shop and they would have to re-weld the 2 pipes to one
The sound of 4 cylinders straight piped sounds like trumpet and I hate the guys on my neighborhood that think they’re cool for being loud as hell is them 😂
They will know it when they get welders flash, and they can’t see it. They’re blind for life it’s not a joke it’ll burn your eyes. and it burns like sand in your eyes all the time they think it’s only for a couple seconds now they’re blind for life. What are you doing? Even using a cutting torch acetylene you should wear glasses because of the flames. It affects your eyes. It’s not as harsh, but it still affects it.
The cat i took off didn't have a sensor because it was a secondary cat. It had 3 cats, since it was a v6 there was one on each header. Those ones had it. This one didn't. No engine light
OMG, started welding with no hood, nothing protecting your arms and then I look and you have latex gloves on 😆. I hope that little bit of welding you did before you got a welding helmet on didnt burn eyes. A helmet is always a must for welding. You can skip all the other stuff but always have to protect your eyes. If not you will burn them and feel like someone threw sand in them. Good upload though
Thank you very much James, I have learned alot since then. But I appreciate that you enjoyed the video. Stay tuned for awesome new videos. Like and subscriber
@@erickosolismartinez9523 I wouldn't know. I have always worn a helmet. Just stating what was told to me when I started welding many years ago. People should always protect their eyes though.
louder and misfiring due to lack of back pressure because cat was taken off.....he should have left the cat on, now he needs to spend on an ECU remap to get it firing properly.
Not really he filmed himself committing a felony and yes cutting off your cat is against the law, federal law that is. He better hope it was not done in a business because it follows with 100's of thousands of dollars of fines on top.
Its not illegal to cut off anything in your car, its illegal to drive an unsafe vehicle on public roads. Some people use their "ilegal" cars on private roads or tracks only, which is legal. Take a racecar for example. We in the buisness call these trailer princesses. Because they only leave the trailer for storage, maintanance/modification, or racing.
Lil buddy that's supposed to be teaching him keeps setting him up for failure, like letting him weld with no eye protection, not showing him where to cut the cat off, not pointing out the cat is bolted on one side and making it more difficult to install or remove because the bolted coupler midway was replaced with a solid weld done by a solid welder and now the pipe has to be welded on, and cut off to be removed instead of removing 3 bolts. I'm sure there's more this guy didn't show him how to do the work properly but let me know if you agree?
How the hell this guys survived this long?? No straps on the pipe they are cutting No face shield Using wrong tool No welding mask shield eye protection No right clothes Oil fumes and throwing sparks everywhere Good luck guys
@@salimkarimov7401 oh ok thank you. My upstream oxygen sensor melted because of a head gasket leak I already fixed and somehow ended up at the location where I had my muffler deleted. So even If I did want to get a full delete I would still need both sensors so yeah going to buy the one I need tonight at AZ.
It does, but if you can find a good ecu tune shop. They can get it done for you. Another tricked I've learned is if you cross wire the oxygen sensor and the light goes away
Where are the adults in this shop? I mean his hand was right beside the side grinder cutting wheel, he was staring directly at the ark while the Rodriguez guy welded, then he starts burning wire without a sheild. Did he wake up later that night with retna burn?
Yeah I can’t find any shop around to actually weld a pipe in place of my 3rd cat they said they won’t touch it and the only way is to put a cat back in place of it. They said it’s a $25k fine. I asked them how in the works are there so many people doing these performance exhausts Catless none of these shops has the answers
You can buy a high flow catalytic converter. Or you can do it yourself. You don't need a welder. There are exhaust clamps and exhaust pipes at your local parts store. Just time consuming is all
@@salimkarimov7401 well right when the 2 banks merge to the Y pipe is a pipe that is like 4” or so it’s huge then welded to the cat then right after the cat it steps down to a small pipe I think 3” so I need a pipe that is stretch to like 4.25 on one end to 3.something on the other. It seems weird but it’s all factory. Thought about just buying the whole header kit and y pipe from TSP. But either way I may just see if the shop will cut me pipe and stretch it on one end and I buy it and the clamps
@@hemi5.7villain problem solved last month. Friend of a friend used to work at the exhaust shop. She was able to cut out all the cats and weld in and bend where necessary. I then took it to have it all tuned out and an initial tune done. Runs very good deleted the dod afm. Next I’ll get it tuned all the way including trans but I may be putting in 4.10 gears it has a 6l80 6 speed so it shouldn’t be too bad when I occasionally use the interstate
Go ahead be a idiot cut that flex pipe out do you have busted exhaust manifolds? There’s a reason for that so when the motor twist it flexes or you people ridiculous you don’t know don’t do something.
This is like watching homer simpson work
Bro fr
LMFAOO
Painful, so painful.
Rodrigo is ned Flanders
🤣💀
This guy single handedly made insurance premiums go up.
I love how your buddy just lets you weld with No eye protection 🤣😂🤣
F’ing mint 😂
Probably his buddy wants out of the shop for few days😊
You people are ridiculous. You just worry about a weld. The EPA should be going to every location and shutting every shop down every muffler shop and putting the owner in jail for it because they know it’s illegal they should not be doing it it’s tampering with federal emissions.
Aren’t you people learn how to speak saying probably you don’t know you’re not sure if you’re self
@@CharlesLease-ei1eefound the liberal tree hugger
“Close your eyes”
Him 👁👄👁 stares directly at it
Hahahaha that made me laugh.
When using the cutting wheel, you and those nearby need to wear a full face shield. When welding, use a welding mask. When painting, use a respirator intended for painting. Be safe because injuries suck!
a face shield for cutting/grinding is the most liberal shit i’ve heard learn how to use a grinder
I can’t stand people when they take the cutting guards off of grinders because they can’t get close enough to it. Use a different Saul or put a new blade on it. They want to run it all the way down to nothing there is a reason why it only cut to a certain point it is call safety.
Your just a whuss.
My first thoughts when I saw this video.
The _"I literally have no idea what im doing"_ was surprisingly reassuring since after seeing a fellow practitioner of the bruteforce method it sparked great confidence in me after realizing i wanted a catdelete this morning.
The go with the flow figure it out along the way is severely underappreciated and has always served me well. most of the time. Sorta. 80% of the time it worked every time so the odds are in my favor
imma just go for it
Just going with the wind. Or in this case the cutting wheel and welding
did he just weld with no mask what 😂
Idiot going to lose high eye site real quick
His*
Fr when i saw that i was like PUT ON A MASK
@@MaseFade Ironically calling someone else an idiot as you spelled his and sight wrong. Then you only correct yourself on 'his' and not 'sight'.
@@jesusislord4060 facts lol my bad
This man gives me anxiety holy shit
Haha why?
@@salimkarimov7401 You operating power tools is scary. Watch your hands and fingers bro.
😂😂😂
He’s good yet
Also welding with no mask
Omg did you really just weld with your eyes open ? 😂😂😂😂🤦🏽♀️
Thomas Shelby he’s fucking stupid hahah has bet he was crying that night haha I hate ark eye
Haha yeah, my eyes are pretty bad already so it doesnt bother me as much
Lewis Jones yeah man I thought the same ark eye is seriously a bitch , couldnt sleep properly cause of it when I got it,
Salim Karimov you’re eyes are one of the most important things on your body. Looking at that light can make you go blind.. smh
Gonna feel that flash burn real good
Stay away from power tools..and i mean that sincerely..
@Guitargreat right..who hired him?does not even know what a sawl zahl is just waiting to see him cut off a finger..i dont know some people just SHOULD NOT do certain things.
Psych!!
Don't know about u guys but i love this dude😁
Thanks my guy. Hope you enjoy it
This man was staring straight at the welding😂 I hope you can still see. Also you’ve gotta be a lot more careful with the grinding disc I’ve known quite a few people to have to go to the hospital holding them like that
😂😂😂
😂😂😂😂😂😂😂he a legend for that
I can’t wait to get home and watch this cause I scrolled to the comments right away and now I wonder what I’m missing out on😂
Watch all my videos. Hope you enjoy them
you should have removed the cat with a wrench at the flanges then straightpiped flange to flange so that you can reinstall the unused cat for smog and it doesnt show any signs of modification
Maybe there's no "smog" where he lives lol
Stared at another man welding for ~15 straight seconds with bare eyes while holding a hood in his hands LOL
How does this affect the vehicle performance now that there is very little back pressure? I've heard mechanics say cats are necessary because they provide back pressure for the correct HP.
Raccoon Willie
That's the EPA who say that! Not mechanics!
The vehicle will actually need to be tuned now for adequate performance as more air flows you need more fuel to mix otherwise it sounds like sh!t like this car and you will actually lose performance. All in all it works amazingly when done properly and with the help of someone that can adjust fuel injection rates. Otherwise you are wasting your time. Also if you move sensors around a bit you will still pass any inspection and wont throw codes. This was kinda a backyard DIY vid it seems.
Welp, hes not gonna be the new champion catalytic converter thief.
🤣🤣🤣
3 cats? Welp 12 o clock at night grab a jack and battery sawzal we gettin rich tonight hahah.
What does your comment mean??
@@loueretabrown9956 That cats are worth a lot of money dumbass
Underrated comment
Almost every car has 3 cats ...
@@loueretabrown9956 he's gonna steal them because cats go for a lot of money
This man will never touch my vehicle.
😆😆😆😆😆😆😆😆😆😆😆😆😆😆
just staring at the weld like it ain’t nothing 😂
😂😂
Ummm... the right tools for the right job maybe???🙄
Is this comment because of the grinder?
Regular steel hardwire?
Did you get flashburn?
No I did not
Running straight pipe now
manifold exhaust turn red. Any suggestions i tried everything
Turned red? What do you mean?
@@salimkarimov7401 it gets so hot it turns cherry red
dude has been to ER prolly 3-4 times a year...LOL
I want to straight pipe my towncar. Is it ok to delete front cats also
Its up to you. But if it has O2 sensors then it will give you a check engine light
@@salimkarimov7401 ok light now front cats clogged
@@MrBodean2010 you should replace them or buy aftermarket high-flow cats. Again its up to you
Is it a genisis
Tiburon. The father of genesis
Dear can we bye pass catalytic converter .
What do you mean by bye pass?
nice, hope you've gotten better at welding, it's a very useful skill.
Yes I have. Thank you for asking
Are you people serious? You’re worried about a well job. Nobody could see that all they hear is that ridiculous sound
You really need to get into another line of work. You have no concern of your own safety and well being. Use some common sense ,you only get one set of eyes in this lifetime.
He just wet behind the ear. Just cause he's green don't mean he should stop. I am sure he's researched, studied, and experience more in this field of work.
It’s good that your learning but you should really do some health and safety bruh , all the best stay safe man 👍🏼💯
Why you calling me fat. Haha
After seeing this video I learned how to fix the car THE WRONG WAY!
1st u need to use gloves not the ones you stole from dentist
2nd cut the cat off between the mounting flanges ( pre bend pipe if needed before starting the project
3rd is practice welding on the ground 1st
4th wear a welding helmet, even if u just spot the 2 metals without a shield u will feel your eyes burning later
Just think safety 1st
And you need to do a before and after sound of exhaust so that people can hear if the modification will make a diffrence on there car
probably the emergency room and not the dentist
VZ
And you need to do a comparison of your spelling and the difference between there and their before and after an English course, grade 5 or 6 I believe!
I have a good feeling my welding teacher will use this as a video of what not to do.
I hope it helps
I just had a pipe welded onto my Ford Taurus se.The guy said he was gonna gut the other two I believe. Now it runs a little loud while idling. But my speed is back up.
it could be that your cats were clogged just like mine so it sounded like it was normally quite. but now since they are new or deleted you have more air flow which could make it louder.
So would it fkk up the car if you do cat delete 🤔
Please don't use a cutting wheel ever again.. they already have a bad rap...
What is the name and location of this exhaust shop
Since it is not my shop I can't disclose that information
Take the heat shield off convertor. Cut a small square 3 sided hole in convertor, bend metal back. Take a hammer drill with a chisel adapter, break all the honeycomb out, weld the square shut. Done. This will keep piping all in one piece and much safer.
zip cut blades can blow apart, you should be using a guard and keeping your face out of the blades trajectory path... I never use a guard, only with zipcut blades, man that was stupid.
thanks bro. i appreciate the the advise and i know that. at the time i didn't have one and couldn't afford one.
Thank you for this video!
You are very welcome
I have a 2008 Ford Escape Hybrid by removing the catlytic converters do y’all think it would instantly affect the truck’s performance since it’s an electric hubrid??? thank you
It won't really affect performance in a negative way. It will actually give you more airflow and will give a better sounding noise
@@salimkarimov7401 thanks man appreciate the reply wont also start smoking right?
@@raulmartinez6722 no it won't start smoking
Now I know why men lives shorter
My v6 accord gave 2 codes respectively P0420 & P0430. Any suggestions besides changing the cats?
You can try fuel cleaner to clean the deposits and remove alot of the clogged dirt and stuff. That's the cheap way. But it will take a few times.
Or your sensors can be faulty. You can take them out, clean them and your good. If that doesnt help then you might need to replaced
Salim Karimov Thx man but I used lacquer thinner half tank, drove about 150-200mi and the code disappeared. So far so good man...
Great bro. Let me know if you need anything else
Salim Karimov The code come back again
What do you do with a Y pipe converter
Please give more detail for me to be able to give you the best answer I can give
@@salimkarimov7401 the pipes split one to manafold one to the back
@@spiritualangel824 whats the year make and model
@@salimkarimov7401 96 3500 dodge ram van
@@spiritualangel824 those you would have to buy a new one. If it was just a straight pipe that you can cut from each end then it would be easy. Or you can take it to a shop and they would have to re-weld the 2 pipes to one
The sound of 4 cylinders straight piped sounds like trumpet and I hate the guys on my neighborhood that think they’re cool for being loud as hell is them 😂
I agree
Fuck u, inline4 engines have beautiful sound.
@@fiklicernas8298
So do turbo powered golf carts
DON’T look at the welding being done without a mask.....arc eye !!
They will know it when they get welders flash, and they can’t see it. They’re blind for life it’s not a joke it’ll burn your eyes. and it burns like sand in your eyes all the time they think it’s only for a couple seconds now they’re blind for life. What are you doing? Even using a cutting torch acetylene you should wear glasses because of the flames. It affects your eyes. It’s not as harsh, but it still affects it.
hey everyone learns it just takes time keep it up bro ❤️
Thank you. I appreciate it. I will be uploading more
Tiger Patch exhaust tape works awesome!!!!!!!!! I gets at hard as steel after it cures. No Bullshit!!!!!
Thank you
12:09 your eyes 😂😂
Were did he plug the 02sensor after deleting his cat that would cause his engine lights to come on
The cat i took off didn't have a sensor because it was a secondary cat. It had 3 cats, since it was a v6 there was one on each header. Those ones had it. This one didn't. No engine light
My cats its been cut off and my check engine light on how do i turn it of 🤨
@@joebadd9667 Put in new cats and o2 sensors
@@flippyhustle5713 first class comment sir.
U mean to tell me, without the cats, u still have to buy 02 sensors.
OMG, started welding with no hood, nothing protecting your arms and then I look and you have latex gloves on 😆. I hope that little bit of welding you did before you got a welding helmet on didnt burn eyes. A helmet is always a must for welding. You can skip all the other stuff but always have to protect your eyes. If not you will burn them and feel like someone threw sand in them. Good upload though
Thank you very much James, I have learned alot since then. But I appreciate that you enjoyed the video. Stay tuned for awesome new videos. Like and subscriber
Not sand like someone put out a cigarette on your eyes
@@erickosolismartinez9523 I wouldn't know. I have always worn a helmet. Just stating what was told to me when I started welding many years ago. People should always protect their eyes though.
I speak from experience when I was a kid
Watching this guy work... makes me feel like and expert next to him...🤣🤣🤣🤣
Thats what I'm here for my guy. For you to become an expert
Sounds nice👍🏿
Did it do louder??
Yes
louder and misfiring due to lack of back pressure because cat was taken off.....he should have left the cat on, now he needs to spend on an ECU remap to get it firing properly.
Girl cant even speak proper english🤣
I was cringing wile you were cutting with your hand there.
Everyone seems too
did a check engine light come on
Nope
Rodrigo is smart
Po Panda yeah he knows his trade
Not really he filmed himself committing a felony and yes cutting off your cat is against the law, federal law that is. He better hope it was not done in a business because it follows with 100's of thousands of dollars of fines on top.
Its not illegal to cut off anything in your car, its illegal to drive an unsafe vehicle on public roads. Some people use their "ilegal" cars on private roads or tracks only, which is legal. Take a racecar for example. We in the buisness call these trailer princesses. Because they only leave the trailer for storage, maintanance/modification, or racing.
2:49 "I literally have no idea what I am doing." Yes, this is where I stop watching. If you are looking for a how to...this is not the video for you.
Thanks for the heads up.
I was wondering what kind of car made that noise?
Will I get pull over in tx deleting cat,,,
i dont think you will get pulled over as long as its not too loud. you wont be able to pass emissions if you get an engine code however.
@@salimkarimov7401 got it fix.cleaned.they did put a straight pipe but with waaaaay less noise
@@salimkarimov7401 I just got it replaced,,n a straight pipe..nothing loud,,
If your state runs runs a yearly vehicle check the emissisions will fail whether you get an engine code or not.
I know everyone's giving you shit, but props for just diving into it. Not everyone can do that.
😂😂anyone on the planet can do what happened here.😂😂 not many can do it properly and get the desired effects.
Man should wear a face shield anytime you cut with a grinder and wow there goes your eyes 😂
What is the car?
2005 hyundai tiburon
This guy is DANGEROUS..!
There are plenty of SAFER ways than this fool..!
Lil buddy that's supposed to be teaching him keeps setting him up for failure, like letting him weld with no eye protection, not showing him where to cut the cat off, not pointing out the cat is bolted on one side and making it more difficult to install or remove because the bolted coupler midway was replaced with a solid weld done by a solid welder and now the pipe has to be welded on, and cut off to be removed instead of removing 3 bolts. I'm sure there's more this guy didn't show him how to do the work properly but let me know if you agree?
electric motors have a tremendous amount of torque I would never hold that grinder with one hand two at that angle was dangerous enough
Thought you were gonna send that disk into your body. Take your time. It's quiet while its idling because you still have your resonator in.
When I said it was quit the whole exhaust was off. But true, I should've taken the resonator off
What have you achieved?
In my life? Not much haha
@@salimkarimov7401 what have you achieved in cutting and deleting the catalyc converter ? ? Is the car not making a wild noise like helicopter?
How the hell this guys survived this long??
No straps on the pipe they are cutting
No face shield
Using wrong tool
No welding mask shield eye protection
No right clothes
Oil fumes and throwing sparks everywhere
Good luck guys
I have a question? Where will the oxygen sensors be attached to if there is a delete?
There isn't a oxygen sensor on secondary cats. They just extras ones
If they had one you would buy the cat delete pipes that come with a hole for the oxygen sensors to go
@@salimkarimov7401 oh ok thank you. My upstream oxygen sensor melted because of a head gasket leak I already fixed and somehow ended up at the location where I had my muffler deleted. So even If I did want to get a full delete I would still need both sensors so yeah going to buy the one I need tonight at AZ.
@@israelcruz6274 good, hopefully I was helpful
@@salimkarimov7401 yeah my car already smells like gas so yes it is necessary I believe so.
Wow........ I am dumbfounded by this guy.....
Rewatch the whole video. Maybe you won't be dumb after. Maybe 3rd times the charm
Not to be mean but now I see why he is wearing glasses 😁
Doesnt a cat dlt throw up warning lights?
It does, but if you can find a good ecu tune shop. They can get it done for you. Another tricked I've learned is if you cross wire the oxygen sensor and the light goes away
@@salimkarimov7401 Still illegal to take off an antipolution device that the car was design to have.
@@stef2797 its illigal if its the primary cat. do any of you actually watch the god damn video. i know that.
Where are the adults in this shop? I mean his hand was right beside the side grinder cutting wheel, he was staring directly at the ark while the Rodriguez guy welded, then he starts burning wire without a sheild.
Did he wake up later that night with retna burn?
Right here. An adult.
Is that a Tiburon?
Yes it is
Very good video
Thank you
Working with a butter knife 😂
Protect your eyes FFS!
So did a engine light or anything come.on after the cat delete
No
Of the topic but I got the same sweater u had in the first clip
I’m doing the same thing
Yeah I can’t find any shop around to actually weld a pipe in place of my 3rd cat they said they won’t touch it and the only way is to put a cat back in place of it. They said it’s a $25k fine. I asked them how in the works are there so many people doing these performance exhausts Catless none of these shops has the answers
You can buy a high flow catalytic converter. Or you can do it yourself. You don't need a welder. There are exhaust clamps and exhaust pipes at your local parts store. Just time consuming is all
@@salimkarimov7401 well right when the 2 banks merge to the Y pipe is a pipe that is like 4” or so it’s huge then welded to the cat then right after the cat it steps down to a small pipe I think 3” so I need a pipe that is stretch to like 4.25 on one end to 3.something on the other. It seems weird but it’s all factory. Thought about just buying the whole header kit and y pipe from TSP. But either way I may just see if the shop will cut me pipe and stretch it on one end and I buy it and the clamps
@@nickgrayy alright. I hope everything goes according to plan. Keep me updated or if you have any questions
You call the shop or you went directly to them sometimes you go up there directly it might be something different
@@hemi5.7villain problem solved last month. Friend of a friend used to work at the exhaust shop. She was able to cut out all the cats and weld in and bend where necessary. I then took it to have it all tuned out and an initial tune done. Runs very good deleted the dod afm. Next I’ll get it tuned all the way including trans but I may be putting in 4.10 gears it has a 6l80 6 speed so it shouldn’t be too bad when I occasionally use the interstate
I feel like cutting the flex side first then cutting the pipe side second would have gone better
Go ahead be a idiot cut that flex pipe out do you have busted exhaust manifolds? There’s a reason for that so when the motor twist it flexes or you people ridiculous you don’t know don’t do something.
Sawzall would have cut it off in 60 seconds
And that's good for the car????
Actually it is especially even more if the catalytic converter is clogged. Gives it a better airflow for the engine and cooling system
@@salimkarimov7401 cool thinking about doing that to my 2005 navigator
Thanks for the upload, now I know how not to do it.🤣
You are very welcome
Mexican guy to the rescue!!
For real. Awesome dude
What is the song used at the beginning?
French lemonade by senpai ru
ayo this foo hilarious 😂😂😂
Two Words.. Reciprocating Saw!
2 words. Got it 👍
Crimson Chin would be proud
Who is that?
Oh hahaha
You should’ve done to catch elites
Emilio Estevez working on cars now
*stares directly at 10 second arc*
Haha yup
🙏 Really appreciate the sub
Did you remove your o2sensors? And did it trip the check engine light
No sensors were there. This was the secondary cats. No check engine lights or anything.
He’s gonna get one hell of a flash burn
Nope didn't get one
5:16, best part of the video! cheers
I agree haha
Bros definitely needing stronger glasses after this vid
Surprised osha hasn’t showed up
Greatness
Bro you don’t supposed to make sparks under your fuel tank