Nice video ! I do have a complete unrelated question however ... Can you tell me what background you have with the bridge or what bridge it is? so nice !
In order to change the camera's to motion only you need to go to event settings and turn on the check box for motion. this will enable the system to use motion. Under settings and storage manager this is where you state what will be recorded. either full record ( Green ) or Motion ( Yellow )
Why internet network.Can it work in village without any internet connection to any public network??? or without any mobile device phone or computer. only TV with HD input???
How did you get Dahua NVR to recognize Hikvision Cameras on your network? Are you able to view the actual live feeds of Hikvision cams and record to hard drive in Dahau NVR?
Just watched the video, not bad, I guess if Hikvision is ONVIF enabled and Dahua NVR has the same standards , it must work. I'll have to check it out as well.
Hikvision cameras will work on this NVR because I had some setup already. You have to enable ONVIF function and create an ONVIF user and password. Assign Hikvsion ip camera within the same range of your network.
Is it a must to plug in the camera's in the NVR? I have DAhua camera's on my network, but I have them in a different POE SWITCH. Can the NVR pick them up and record for the cameras?
thanks for information. i have swann nhd 815 cameras and just bought dahua5216 p NVR. is there any way that i can connect each other? thanks in advance.
Does it record and display without pluging the network cable ? Can i just plug the camera cable only for viewing and recording? i do not have network connection on my construction site.
I ordered on of these NVRs and I am worried about it overheating. I live in Southern California and it's often hot here. Does heat continue to be a problem? Is there some way to put a fan in the case? Thanks.
Hi, Good video. Why it is necessary to change the default IP addresses? Can't we continue with default IP addresses? Secondly, how we can do multiple display if we have another LCD?
what if the default ip address is directly to the network range of your network? So if this is a stand alone camera system then its fine to use default. However, if you are connecting to an already present network, you will need to adjust the default ip address to match the other ip address range of the home network. Multiple displays can be done on only some NVRs. If you have both hdmi and vga, you may be able to use both but some NVRs dont allow it. In that case you would need to get a amplified splitter.
@@ecologicaltime Thanks for reply. will the splitter do any problem to showing multiple display? Secondly, do you make any video regarding how to take recording (any specific date and time) backup into USB?
Sir I have Dahua XVR DH-XVR4B04. I have enabled motion detection. In region setting I have tried multiple settings for sensitivity and threshold but the alarm triggers for shadow falling on the selected region and not when actual human being enters select region. Can you help
hi. really appreciate your time in creating these videos. thank you. Could you please help me. l have the dahua ip cameras and recently l went from pss 4.06 which was quite good at downloading camera footage to smart pss 1.14 or 1.15. it now takes overnight to download say 2 hrs of footage. my internet speed hasnt changed its quite fast. any ideas how l can fix this? maybe l shouod try an old version ? or am l using the wrong program even?
want to know more about frame rate, what the maximum number of frame rate...i watch it that show 20 fps in maximum resolution..but if it set to medium resolution just say 640x480 so is it still maximum 20 fps ?
Hello, I'm about to buy a system with the 2Megapixel Full HD 30x Ultra-high Speed HDCVI PTZ Dome Camera. I want the NVR, Do i need anything else for a 2 cam system? (ie.cables,POE switch's) I also want to view live on network and record at the same time, is it possible?
Hi, i set up my dahua ip cam thats linked to my nas but on the motion detect "area" tab oh dahua interface the settings are covered by a window of the camera view so i cant adjust anything, I've tried to fix it but no joy, kinda stuck, any advise please?
Dear Sir I have install Dahua ip camera with micro sd card without NNR. But now the problem is this when i copy sd card data there is then a format problem. they give me .dav format but i need mp4 format. What to do now? is it possible to get it in mp4?
Hi there, I have a Dahua 16 channels NVR with 4mp Dahua cameras but I can't even get the PTZ to work - I have tried different PTZ profiles as as well as setting the PTZ to 'Remote' rather than 'Local' . I have also tried doing it while connected straight to the NRV, from a local computer as well as from a remote computer however I had no luck. I have set up pretty much everything else apart from PTZ. Any suggestions?
Some of dvr have inbuilt setting of ptz or some dvr could not support Ptz function u need to change cable in camera and give some extra power to camera
One important question plz.. How your cameras connected to your NVR? Each one in different subnet each one in different network. So how they connect to each other?? Your ip cameras 10.1.1* Your NVR 10.0.0.*
look closely and check if they do, its unlikely that they have the same address if they are on the same network. However, if they show the same address, which is possible, it will result in one camera streaming and not both. one takes priority or they toggle from time to time. My advise is to change one of the addresses. I have a video on the IP address conflict issue th-cam.com/video/EG2-ynXXyCI/w-d-xo.html
quick question I hope someone can help me. I've set up my NVR with a computer monitor and configured the harddrive etc. I added 3 cameras, but only 1 is accepted and running. The last two shows "Account has been blocked" -I can login from the WEB Interface, to the last two cameras if I set up a static IP address. I've been through any settings I can possibly think of... There are no reset button on the cameras (checked everywhere). I've reset the NVR 3 times so far, disconnected the PoE on the cameras multiple of times and have not gained an inch closer to setting my camera system up and running... My cameras are: IPC-HFW1420S If somebody could help I would really appreciate it!
D Shvan there is a small watch battery on the circuit board turn of power take the battery out wait 30 sec put it all back together and it will be factory reset
sir in my office we have panasonic NVR. recently i forgot the password for that system. I cant login to gui and also web is there is any solution to reset password. K-NL308 model
I wouldn't waste my money on this shocking system. Since I purchased a 4K NVR v4.0 and 8 cameras a year ago, I've had problems after problem with live video and its mobile app, gDMSS. Hard to set, hard to have a smooth flow live video, hard to review recorded video on PC screen and mobile app. Freezes a lot. Sometimes notification aren't received and then all of sudden the notification I didn't receive earlier are being released all at once. Plus, its supposed to be a 4K system, I am lucky to get 10.80p or 720p. Plus, all this time I've spent trying to fix these problems by contacting the seller or Dahua support to no avail. It's all questions and answer. You find the question that matches you need then click on it and you get the answer. That's all you get as support. Nothing Like or Live Chat. And that stink. Another reason I will not recommend this product is, if I have a problem I have to turn to TH-cam for help, but they are security cameras installers and if you try and ask they will ignore you. In fact, it's too much to explain it all but I do wish to say I won't recommend it to anyone.
Thanks for the video, lots of good information on setting up the motion detection only recording.
Nice video ! I do have a complete unrelated question however ... Can you tell me what background you have with the bridge or what bridge it is? so nice !
thanks. i think it was a screensaver pack i downloaded from Microsoft. I think its Manhattan bridge or one of the bridges to NYC.
In order to change the camera's to motion only you need to go to event settings and turn on the check box for motion. this will enable the system to use motion. Under settings and storage manager this is where you state what will be recorded. either full record ( Green ) or Motion ( Yellow )
Why internet network.Can it work in village without any internet connection to any public network??? or without any mobile device phone or computer. only TV with HD input???
How did you get Dahua NVR to recognize Hikvision Cameras on your network? Are you able to view the actual live feeds of Hikvision cams and record to hard drive in Dahau NVR?
i have not tried that. The NVR sees the cameras on the network but i dont think it streams them though. I would have to fiddle.
Just watched the video, not bad, I guess if Hikvision is ONVIF enabled and Dahua NVR has the same standards , it must work. I'll have to check it out as well.
Hikvision cameras will work on this NVR because I had some setup already. You have to enable ONVIF function and create an ONVIF user and password. Assign Hikvsion ip camera within the same range of your network.
Is it a must to plug in the camera's in the NVR? I have DAhua camera's on my network, but I have them in a different POE SWITCH. Can the NVR pick them up and record for the cameras?
thanks for information. i have swann nhd 815 cameras and just bought dahua5216 p NVR. is there any way that i can connect each other? thanks in advance.
Does it record and display without pluging the network cable ? Can i just plug the camera cable only for viewing and recording? i do not have network connection on my construction site.
you need the NVR and the cameras(s). You do not need an entire network.
I ordered on of these NVRs and I am worried about it overheating. I live in Southern California and it's often hot here. Does heat continue to be a problem? Is there some way to put a fan in the case? Thanks.
no it was fine even in summer of 33 degrees C.
is it able to connect to Onvif compliant IP camera?
Hi, Good video. Why it is necessary to change the default IP addresses? Can't we continue with default IP addresses?
Secondly, how we can do multiple display if we have another LCD?
what if the default ip address is directly to the network range of your network? So if this is a stand alone camera system then its fine to use default. However, if you are connecting to an already present network, you will need to adjust the default ip address to match the other ip address range of the home network. Multiple displays can be done on only some NVRs. If you have both hdmi and vga, you may be able to use both but some NVRs dont allow it. In that case you would need to get a amplified splitter.
@@ecologicaltime Thanks for reply. will the splitter do any problem to showing multiple display?
Secondly, do you make any video regarding how to take recording (any specific date and time) backup into USB?
Sir I have Dahua XVR DH-XVR4B04. I have enabled motion detection. In region setting I have tried multiple settings for sensitivity and threshold but the alarm triggers for shadow falling on the selected region and not when actual human being enters select region. Can you help
hi. really appreciate your time in creating these videos. thank you. Could you please help me. l have the dahua ip cameras and recently l went from pss 4.06 which was quite good at downloading camera footage to smart pss 1.14 or 1.15. it now takes overnight to download say 2 hrs of footage. my internet speed hasnt changed its quite fast. any ideas how l can fix this? maybe l shouod try an old version ? or am l using the wrong program even?
I have some question with kind of this NVR. Can I set up this using P2P? fro remote viewing. without the portforwarding and DDNS.
I already have CAT 7 cable ran throughout my house. Would this work with CAT 7 cable?
CAT7 just means you have a higher spec cable that can handle higher data rates so yes it would work
@@ecologicaltime Thanks for the replied !!
so many thank for your sharing
want to know more about frame rate, what the maximum number of frame rate...i watch it that show 20 fps in maximum resolution..but if it set to medium resolution just say 640x480 so is it still maximum 20 fps ?
Can you connect your Hikvision cameras to this nvr ?
Noticed 3g in network settings. What the model of nvr is it? How did you get 3G modem settings in menu?
Did you test to connect the HikVision camera yet to the Dahua?
Andree Helmersson did you have an answer?
Hello, I'm about to buy a system with the
2Megapixel Full HD 30x Ultra-high Speed HDCVI PTZ Dome Camera.
I want the NVR, Do i need anything else for a 2 cam system? (ie.cables,POE switch's)
I also want to view live on network and record at the same time, is it possible?
you need a hard drive, cat 5e cable boots and rj45s, crimper. live view- you will need a cellphone or a pc
Hi, i set up my dahua ip cam thats linked to my nas but on the motion detect "area" tab oh dahua interface the settings are covered by a window of the camera view so i cant adjust anything, I've tried to fix it but no joy, kinda stuck, any advise please?
Dear Sir
I have install Dahua ip camera with micro sd card without NNR.
But now the problem is this when i copy sd card data there is then a format problem. they give me .dav format but i need mp4 format. What to do now? is it possible to get it in mp4?
This NVR could work with BOSCH CAMERAS?
Hi there, I have a Dahua 16 channels NVR with 4mp Dahua cameras but I can't even get the PTZ to work - I have tried different PTZ profiles as as well as setting the PTZ to 'Remote' rather than 'Local' . I have also tried doing it while connected straight to the NRV, from a local computer as well as from a remote computer however I had no luck. I have set up pretty much everything else apart from PTZ. Any suggestions?
Some of dvr have inbuilt setting of ptz or some dvr could not support Ptz function u need to change cable in camera and give some extra power to camera
Hi pls, what is the meaning of residue bandwidth on dahua nvr
Do you still prefer the hikvision DVR to the Dahua?
nope. Dahua is good
One important question plz..
How your cameras connected to your NVR?
Each one in different subnet each one in different network.
So how they connect to each other??
Your ip cameras 10.1.1*
Your NVR 10.0.0.*
same subnet.
Hi mate could you send me link to buy this hard drive
please
HELP PLEASE connect the nkb1000 to the nvr 16ch4k managed to control the nvr but the ptz ip managed to move left right up down but not zoom help
Sir please can you make video on heitel nvr full setup please!!!
Our cameras have the same ip address. Hows that?
look closely and check if they do, its unlikely that they have the same address if they are on the same network. However, if they show the same address, which is possible, it will result in one camera streaming and not both. one takes priority or they toggle from time to time. My advise is to change one of the addresses. I have a video on the IP address conflict issue th-cam.com/video/EG2-ynXXyCI/w-d-xo.html
Why not use smart pss instead of the browser version?
+piet beier yes i will do a video on that.
Great :)
+piet beier th-cam.com/video/8MQ8J2mvUY8/w-d-xo.html
SmartPSS video
does this reconize hikvision cams?
It sees them on the network but i have had trouble getting them top work with the Dahua
How to trun off sleep mode off
I'll try this setup in my Xeoma software
How to get rid of image ripple in nvr dahua
what is the default ip of "dh-ipc-hfw2231tp-zs-s2"IP CAMERA
quick question I hope someone can help me.
I've set up my NVR with a computer monitor and configured the harddrive etc. I added 3 cameras, but only 1 is accepted and running. The last two shows "Account has been blocked" -I can login from the WEB Interface, to the last two cameras if I set up a static IP address. I've been through any settings I can possibly think of... There are no reset button on the cameras (checked everywhere). I've reset the NVR 3 times so far, disconnected the PoE on the cameras multiple of times and have not gained an inch closer to setting my camera system up and running...
My cameras are: IPC-HFW1420S
If somebody could help I would really appreciate it!
D Shvan there is a small watch battery on the circuit board turn of power take the battery out wait 30 sec put it all back together and it will be factory reset
sir in my office we have panasonic NVR. recently i forgot the password for that system. I cant login to gui and also web is there is any solution to reset password. K-NL308 model
Never screw or unscrew HDD with motor screw drive , cause HDD could damage by hard vibration.
Fat chance of that happening if its powered off.
I use my Dahua camera with Xeoma software
Cp plus nvr 8 camera installation
I wouldn't waste my money on this shocking system. Since I purchased a 4K NVR v4.0 and 8 cameras a year ago, I've had problems after problem with live video and its mobile app, gDMSS. Hard to set, hard to have a smooth flow live video, hard to review recorded video on PC screen and mobile app. Freezes a lot. Sometimes notification aren't received and then all of sudden the notification I didn't receive earlier are being released all at once. Plus, its supposed to be a 4K system, I am lucky to get 10.80p or 720p. Plus, all this time I've spent trying to fix these problems by contacting the seller or Dahua support to no avail. It's all questions and answer. You find the question that matches you need then click on it and you get the answer. That's all you get as support. Nothing Like or Live Chat. And that stink. Another reason I will not recommend this product is, if I have a problem I have to turn to TH-cam for help, but they are security cameras installers and if you try and ask they will ignore you. In fact, it's too much to explain it all but I do wish to say I won't recommend it to anyone.
Wtf is the MODEL NUMBER?