You didnt waste my time, Your video & audio is clean and crisp, I Appreciate your Tutorials! I believe I said this not to long ago. Thanks Again Greg, - Ryan
Its nor nearly as hard as youd think. I pulled My Tilly 212 out the box and tore it right open and went stage 2 lol. It's a beast now today as I've learned so much more since then too.
I just ordered the stuff to finish my stage 2 setup and I added the billet side cover because its badass looking and it just happens to have a way better oil drain plug than the stock ones for my setup.
RBG awesome content and the instructions are very clear. It makes me want to build one. I build chevy v-8s and when I do head studs arp reccomends not tightening the studs all the way down. Use oil on the under the head of the fastener to help with proper torque also.
I think a video on installing a electric start on a212 hemi with Honda pts. would be nice for people with mudmoters. Mine is hard to pull start because of the upgrades.
The fact that first of all it’s a 20hp fully built lawnmower engine but second of all There’s still room for improvement Such as hydrolic roller lifters instead of the stock flat tappet ones
I built this exact step up every part you used and I keep blowing belts it completely destroyed my sprocket. What’s the next step on clutches that will actually handle the power and so I can actually enjoy this badass motor
Need a Predator Ghost Billet everything video. Please. And whats the best motor 224cc or Ghost motors to start a build with? If i was to buy all the billet upgrades and more upgrades eventually.
@@trevinskiking2165 they are all clones of a honda gx200 most clones are made with lower tolerence standards. The preditors are pretty good compaired to most clones there are alot of diferences tho between them all
May I share some tech info with you the next time you remove a flywheel rotate the flywheel so you have access to the counterbalance use your pry bars the normal way but instead of hitting the crankshaft strike the flywheel on the Outer Edge at the counterbalance with the hammer it comes loose every time
I didn't have an oil sensor in mind so I didn't need to do thatplus for my Governor whole I tapped it half away and used 1/4 inch allen wrench head plug in red loctite
do I need to vent pls answer I have a stage 2 kit on my motor DynoCams MOD2 Cam ,billet fly wheel ,billet rod,rockers,push rods chromoly,billet lifter,
Soooo I was wondering why you guys haven't been posting. Searched your channel and somehow I'm no longer subbed. I dont know how that happened but just a heads up if your views and sub counts are down.
Jeremy Dubs I guess that makes since. But more then one time I've cracked the rod. Then discovered it was hydraulic pressure from an old head. If it's clean you will always get consistent torque.
I wouldn't suggest putting oil in the hole if it is a blind hole. Doing so will cause a hydraulic lock and snap the rod bolt or pull the threads on the aluminum rod.
Seems you know these predator 212s could you tell me where they suck oil from when rolled over or thrown in a real hard corner. I have a go kart that had a tehcumseh on it and you could roll that thing all day and throw it in a high bank corner in our sand pit and never had an issue I backed into one day and broke the carb off it and I bought a new predator 212 for it and any time you roll it or throw it in a hard corner the thing turns into a fogger for a few seconds or so, it disappears in the smoke.
I'm new to this game but have been riding/racing off road and moto since 1974 so I know my way around a bit...2 things I noticed right off...WHY hasn't someone built a billet intake manifold that loops up and over so when you go to a larger carb or even the adapter/pod filter in the stage 1 kit, its not sticking way the hell out into the wind??...not only is it in the way of riding, but I have seen vid after vid of guys crashing, which is commonplace on these things and wiping that filter or carb right off the motor??....why??....stupid. Another thing, WHY is the header on most of these minis sticking out in the wind from under the seat pan, just behind the aftermarket air filter pod, just waiting to burn the shit out of someones leg??.....that header could be made with a slight bend to the right and route it right under the seat pan and have the pipe route between the rear fender and frame rail, making bolting on a silencer easy-peasy with a bracket bolted to the frame rail......just crazy shit I'm seeing with zero thought put into it.
Hey red beard what length chromoly pushrods did you use? Looking for a set for my tillotson 212 hemi head, I believe I've found the upgraded valve train kit you put on your engine here as well so I think I'm gonna go for that too, it's the only difference between my engine and your build here, plus the fact that I'm running pvl ignition flywheel and briggs coil
I wonder if I should even ask you something. It seems you don't answer a lot of ppl stuff. I just got a mini bike. I got two motors..hemi an non hemi..wanting to do a build on one but I want to get it right when I do an not have issues ppl say they have. Like like same build a 4mod. Think I should do my own vid for ppl like me that done have a clue but want to learn an do one. All American parts of course!
Linda, he used a common crankshaft key - fits in the crank groove & Flywheel keyway slot - Trev New Zealand PS & you can buy offset crank keys upto 8' crank degrees advanced which is 16' degrees ignition.Ask at you local speed Shop or try Isky Cams.T
Do you have a link for the valve spring compressor? I put the ss valve kit and 26lb springs on my hemi last weekend. I got it done but it was really difficult, the spring compressor I had was too big.
![ตีสิบเดย์ [FULL] | อาจารย์โอเล่ ญาณสัมผัส ผ่าดวงคนดัง ประเทศไทยจะเป็นยังไงหลังจากนี้!](http://i.ytimg.com/vi/gszT2O76fL4/mqdefault.jpg)
Hands down you're videos are the most informative. Your chsnnel is the best minibike channel on TH-cam
Learned a lot from this vid. I only repair small engines and this taught me a lot about revuils, thank you.
You didnt waste my time, Your video & audio is clean and crisp, I Appreciate your Tutorials! I believe I said this not to long ago. Thanks Again Greg, - Ryan
I’ve been wanting to do a complete build but I’ve been super nervous about screwing it up. This video gives me the drive to just send it. Thanks man!
Its nor nearly as hard as youd think. I pulled My Tilly 212 out the box and tore it right open and went stage 2 lol. It's a beast now today as I've learned so much more since then too.
You make it look so easy.
I just ordered the stuff to finish my stage 2 setup and I added the billet side cover because its badass looking and it just happens to have a way better oil drain plug than the stock ones for my setup.
The detail in your parts list is amazing. Thanks for jumpstarting this for me 👍🏻👍🏻
RBG awesome content and the instructions are very clear. It makes me want to build one. I build chevy v-8s and when I do head studs arp reccomends not tightening the studs all the way down. Use oil on the under the head of the fastener to help with proper torque also.
I’m building this same exact engine right now and this video is really helpful.
This channel is so helpful. Thanks for making these videos and showing everything.
“Dip the bolts in some ool “ lol
...? OOHHH... you're not used to speaking southern. Bless your heart.
@@Kettenhund75 hahaha I know that one 😂😂
Better than "Goop"...Trev New Zealand
@@Kettenhund75 Its erl🤣
@@Kettenhund75No one is lmao
This is amazing and impressive skill and patience
Like the valve cover and the blue bolts. Great step by step video!
This is what the new hotrod cart needs but with a supercharger 😎
I just bought a hemi 212 and I put it on a little razor dune buggy and it looks like a death trap lol.Nice job Red beard
Dude your videos are truly Ace's , information is awesome.
I appreciate that!
Bubbz and the TARDSQUAD was here🤘🏻😎🤘🏻 God bless brother
Love those engine build videos, nice job brother.
Looks like a beast!!! Awesome build
I have almost the same build. I’m having issues with my carb flooding the intake tube with fuel. Would be nice to see you do a mikuni tuning video.
would love to see you do a performance build on a duromax 7hp electric start
Love the leg lamp in the background! It looks like a "major award".
I think a video on installing a electric start on a212 hemi with Honda pts. would be nice for people with mudmoters. Mine is hard to pull start because of the upgrades.
The G in RBG is now loose. Need to turn it clockwise.......
It would be awesome if you built then tested on a dyno! Be sweet if u had one!
The fact that first of all it’s a 20hp fully built lawnmower engine but second of all
There’s still room for improvement
Such as hydrolic roller lifters instead of the stock flat tappet ones
nice video intruction god bless you
What a majestic beard
Great vid
Ride cymbal going hard
You should do a electronic ignition modification using a magnetic pickup and a GM HEI ignition module and then a powerful ignition coil
Great videos and Go-Kart & Mini Bike builds .
On a Predator 212 with a Stage 2 or 3 can I still run a torque converter ?
Yes you can but it is recommended to get one that is rated for the horsepower your engine is going to produce under the Stage 2 or 3 kit.
How bout a kickstart install on the predator 212cc,...I haven't seen one on a mini bike since the 70's !!!
SilkySlim you can’t because the kick start is opposite of the way the motor spins... you would have to kick it forwards. Akward
Super helpful thanks
Nice wish I had a motor like that
Great job
Hello I'm Filipino and I'm always looking for your videos,hopping that can I buy a billet crank for my 18hp.
Smash the dern like button you RAWK Red Beard
First one to view and comment. You make the best engine build videos on TH-cam!!
Great video
Thanks Papa Redbeard!
I built this exact step up every part you used and I keep blowing belts it completely destroyed my sprocket. What’s the next step on clutches that will actually handle the power and so I can actually enjoy this badass motor
You need to do a 212 with AMR 300 supercharger on the dino
Need a Predator Ghost Billet everything video. Please. And whats the best motor 224cc or Ghost motors to start a build with? If i was to buy all the billet upgrades and more upgrades eventually.
If they make a modified side cover they should add a oil pump and a drilled crankshaft for pleasure lubrication modification.
nice work!
U r AWESOME!!!
attaboy!!!
What will you do with all the leftover new parts??? Sell them?
Way better music this time!
Good
15:30 this the part that I’m worried about 😮
When will you do the stroker build??
Can you please do a review on the coleman 125DX dirt bike
Have you done anything on a ghost motor yet?
04:02 are those the Lifters? I was wondering what those things were called.
Red why don’t you ever port out the heads a bit?
I'm guessing it's so go power sports can demonstrate how much power can be "bolted on"
@@Indiancreekgunsmithing The new predator heads ( both hemi & non ) come with huge ports compared to clones.
@@gastongregory1167 Gaston, a Clone of a Clone ?. Now I've got it .Thanks.Trev New Zealand
@@trevinskiking2165 they are all clones of a honda gx200 most clones are made with lower tolerence standards. The preditors are pretty good compaired to most clones there are alot of diferences tho between them all
@@aaronyoung8132 Aaron I knew all that but thanks for stating it for others less knowledgeable.
How are holding the crank from turning when installing flywheel nut to 65 ft lbs!
looks like the same video as the stage 4 predator build earlier this week
where do you get that cool hardware from
At the 16:00 mark the valve keepers seem to be misaligned. One is i. The grooves and 1 is not. Was this corrected before the engine was ran?
$997+tax for all listed parts with engine. Stage 3 is listed most places @ 16-20hp. Brand spankin new 670cc predator is 22hp for $829.
@Kevin th-cam.com/video/0eMR73e5Rb0/w-d-xo.html
May I share some tech info with you the next time you remove a flywheel rotate the flywheel so you have access to the counterbalance use your pry bars the normal way but instead of hitting the crankshaft strike the flywheel on the Outer Edge at the counterbalance with the hammer it comes loose every time
Right? I have seen so many videos of hammering the crankshaft. Like they have never heard of crank walk.
I’ve heard you need to get a specific flywheel for the hemi, could I use a non hemi flywheel?
I didn't have an oil sensor in mind so I didn't need to do thatplus for my Governor whole I tapped it half away and used 1/4 inch allen wrench head plug in red loctite
Break in please!!!! 🤩
Top de projeto mano 👍👍
Red beardddddd
If anyone can answer this. He’s putting new camshaft why not crank shaft
What brand of table are you using?. I want one of those. The metal coated table.
RedBeardsGarage, where is that pull start handle from??? Cant find it REALLLY like it lol..
It is a rc pull start from ebay
@@RedBeardsGarage thanks for the speedy response brother
do I need to vent pls answer I have a stage 2 kit on my motor DynoCams MOD2 Cam ,billet fly wheel ,billet rod,rockers,push rods chromoly,billet lifter,
That's sweet as...
Do you think the hemi is better or non hemi? I’ve see. We’re you have coil bind and valve Clarence problem but didn’t look like you had a problem here
Soooo I was wondering why you guys haven't been posting. Searched your channel and somehow I'm no longer subbed. I dont know how that happened but just a heads up if your views and sub counts are down.
Where did you get that magnetic dip stick from
So thats a stage 3? Im ported is that a stage 3.5? Since 4 is bigg valve/cut?
Don’t you have to grind something on the crank of the hemi?
Does the arc hemi flywheel have magnets on inside of flywheel to be able to add charging coils for a headlight?
No. If you want charging you should go with the Tilliotson e start. Their flywheels have much higher rpm range than stock predators
I got same motor what all you put in it I want this same build
If i did this complete build for my mi i bike that i love will it still be long lasting
Should i ?
I’m curious as to why you kept the stock piston?
What's the difference between stage 2 and stage 3
the engine teardown at the beginning had the arrow on the piston pointing up? did Braxton assemble it?
Will it hurt the lobes on the cam because of the heavier valve springs
Is there no performance hemie piston head?
Do u always mess with the Chinese remake of the Mikuni only because I was wondering if there any good
Hey RBG why do you dip the bolts for the rod in oil before you put them back in?
so u get consistent torque of the bolts inside an engine
Oh ok thx just wondering
Jeremy Dubs I guess that makes since. But more then one time I've cracked the rod. Then discovered it was hydraulic pressure from an old head. If it's clean you will always get consistent torque.
I wouldn't suggest putting oil in the hole if it is a blind hole. Doing so will cause a hydraulic lock and snap the rod bolt or pull the threads on the aluminum rod.
@@MrMattydavee Sorry Mattydavee I didn't read your comment before I chimed in. But you are correct.
Wow... that flywheel had ~5 degrees of play. Why so much? How much hp would you guesstimate this build is worth?
Seems you know these predator 212s could you tell me where they suck oil from when rolled over or thrown in a real hard corner. I have a go kart that had a tehcumseh on it and you could roll that thing all day and throw it in a high bank corner in our sand pit and never had an issue I backed into one day and broke the carb off it and I bought a new predator 212 for it and any time you roll it or throw it in a hard corner the thing turns into a fogger for a few seconds or so, it disappears in the smoke.
I'm new to this game but have been riding/racing off road and moto since 1974 so I know my way around a bit...2 things I noticed right off...WHY hasn't someone built a billet intake manifold that loops up and over so when you go to a larger carb or even the adapter/pod filter in the stage 1 kit, its not sticking way the hell out into the wind??...not only is it in the way of riding, but I have seen vid after vid of guys crashing, which is commonplace on these things and wiping that filter or carb right off the motor??....why??....stupid. Another thing, WHY is the header on most of these minis sticking out in the wind from under the seat pan, just behind the aftermarket air filter pod, just waiting to burn the shit out of someones leg??.....that header could be made with a slight bend to the right and route it right under the seat pan and have the pipe route between the rear fender and frame rail, making bolting on a silencer easy-peasy with a bracket bolted to the frame rail......just crazy shit I'm seeing with zero thought put into it.
Hey red beard what length chromoly pushrods did you use? Looking for a set for my tillotson 212 hemi head, I believe I've found the upgraded valve train kit you put on your engine here as well so I think I'm gonna go for that too, it's the only difference between my engine and your build here, plus the fact that I'm running pvl ignition flywheel and briggs coil
I wonder if I should even ask you something. It seems you don't answer a lot of ppl stuff. I just got a mini bike. I got two motors..hemi an non hemi..wanting to do a build on one but I want to get it right when I do an not have issues ppl say they have. Like like same build a 4mod. Think I should do my own vid for ppl like me that done have a clue but want to learn an do one. All American parts of course!
How did you keep the Crank from spinning when you installed the billet flywheel?????
Linda, he used a common crankshaft key - fits in the crank groove & Flywheel keyway slot - Trev New Zealand PS & you can buy offset crank keys upto 8' crank degrees advanced which is 16' degrees ignition.Ask at you local speed Shop or try Isky Cams.T
Do you have a link for the valve spring compressor? I put the ss valve kit and 26lb springs on my hemi last weekend. I got it done but it was really difficult, the spring compressor I had was too big.
You never shown how you held the fly wheel in place
He made a bracket that bolts onto the side cover and holds the output shaft in place. Omb warehouse sells them I believe
What is the lift on that camshaft?
Whoooooop neeww video
What’s the point of a billet side cover? It doesn’t add any performance upgrades does it?
Those head studs seem a little short? Not even close to making it through the nut