Thank you for the informative video. This helped me. I found that my HID ballast had blown which was the reason my bike wouldnt start. I switched it out and now im back on the road.
Thanks for the video, this helped me out a lot.. killed two birds with one stone .. my pump wasn’t priming , checked every single thing but didn’t work, the noticed I couldn’t start the bike just to figure out the switch was bad.. Played with the switch alittle, then the pump primed and the bike started up
About 8 years too late 😂 but still have a question for anyone. I have the same issue on my bike except it just takes a few seconds to finally start. It tries and tries and tries and sometimes I have to stop and try again but sometimes it kills the battery. I don't always have to give it gas but it seems to help sometimes. My question is what do you think it could be? My thoughts is either -starter -starter relay -fuel pump Only guess I have. Thanks again 👍 Ride safe 🤙
Great video! One thing that confused me at first was when you were testing the starter relay. The video shows you had the wiring harness disconnected but doesn't show you re-connecting it. This made me question whether the wiring harness was to pass power from switch or to the starter. Also, the camera angle doesn't clearly show the actual removal of the power cable from the relay (I guess it can be inferred by your hand movements). But seeing the beefy relay terminals with my own eyes is what made it obvious that's what the starter is connected to.
When I put the clutch in the gear of my Honda MC22 RR bike, the neutral bulb lights up, I replaced the diode but the problem is the same, thank you for providing a solution
I have a 2006 honda cbr 600rr. An I just ordered a starter solenoid hopefully it will start now.. an also have a brand new battery 3weeks ago..if it doesn't start after this what else do I need to look at?
Thanks for the video! Question for you I'd you get time. I've done all the steps and bike still won't start, I removed starter motor and attached positive and negative to it and it fired straight up but won't start the bike. Can the start be to weak to move the engine or is it likely something else?
Please do a fuel pump problem video!! The two clips that connect to the pump (black goes to the sensor and brown goes to the pump) I use a volt meter on the black and it has 10.56 volts and the brown has 0.00... the cords look to be fine and relays and fuse are not blown...any suggestions😫 fuel pump was on a tank that has been sitting for a long time gas smelled like varnish. Cleaned the tank and changed the pump inside it, but not the whole entire fuel pump. Fuel pump wont prime.. please help
Thanks for the video. So I started the bike by bipassing starter button and it did work. Does that mean i do have a problem with my button? Or wires i suppose. Thank you.
@@williamreilly4676 Not yet but will start by replacing the relays as I also have a problem with my headlights, low beam isn't working and high beam I can't even switch off. I might even try to open the button and see if it's not malfunctioned. Will post here if I solve the problem.
@@ArturK1M after I commented this I tested the wires, no power. So i opened up the kill switch/start button, cleaned the contacts, then tested it again, still no power. Chased wires all the way to solenoid and all seemed fine, ended up peeling back the heat shrink/protective sleeve right below the kill switch and two of the wires were pinched clean in half 🤦🏻♂️ I'm going to splice them and see if it works today. 99% positive it was the issue
@@williamreilly4676 The first connector coming from steering bar under right fairing below tank cover. That was the problem, I literally just touched it and tge bije fired up. Either dirty, loose cable or snapped wire. Let's see, all I did is clean it so far.. Thanks for good conversation!
I bet the service manual for most bikes tells you how to test the internals of a starter too. Under electrical system / starter motor inspection. There should be continuity between armature segments. There should be no continuity between an armature segment and the shaft. Careful, because I measured some continuity that turned out to be my skin.
Your videos are the best. Quick question. I have a 2006 CBR 600rr, she cuts off every time I stop at a light and I have to turn it back on. Sometimes I have to pop start it in 2nd gear after changing out battery and spark plug. Haven't checked the stator but I feel thats what the issue is
Test your regulator first. Sometimes, it gets hot and just shuts the motor off. It's better to test the components than just blindly replace. You'll save some money.
Thank you! This just happened to my Cbr F2 600. Won’t crank seems power is drained and shortage of circuit power.. I believe the stator rectifier is the issue ..
My cbr 600rr 2008 sometimes hard starts when warm Cranks good but doesent fire up only when its hot I have to crank it two times to fire up Any clue? Battery good
Hey for a 03 cbr600rr New battery in it. Intermittently slow cranking. Only once its warm. Slow crank and dies u can hear the starter go click click click really fast.
Any chance you’d do a video about if the motor turns over but nothing else happens ? I’m currently in that situation and after about a month of searching someone mentioned that my tip over sensor could be bad/burnt out ? Have an 05 cbr600rr and it seems most of what you do goes for that as well
Hello, got a 09 honda cbr 600, they guy said something about the previous owner did something with the headlights and now the bike wont start, it turns over but wont start, says it needs and ignition, but before i buy anything was hoping for feedback. I was going to just hot wire it but he said that it would mess up the cpu or something i dont know…😭
So when that main fuse was blown will the clock on the gauge cluster still work? Because mine the clock is on, the battery is brand new and as soon as I turn the key there’s nothing on the gauge cluster at all
If you hear a loud screech while riding and then when you slow down the engine cuts off and and won't start again, you smell a faint burning smell and your battery is good you most likely need to replace the starter, correct?
What happens if you complete the circuit by using your method and the bike starts? What would be my issue? Currently where I'm at. Replaced the solenoid did not solve it
I have an 09green and black 600rr! my bikie shut off on me at a stop light after getting gas, the bike did sit for about 2 months here in pa from november through december
Hello I own a 2007 cbr600rr I have a problem with my headlights that my high beams work but my low beams don't turn on. The bulb is fine. Another thing I thought about checking is the relay, I just can't figure out how to get the headlight relay out to check it. Is it just a pull out? Or is there like a clip holding it in? I checked the fuse, it's fine.
Thanks for your video....i did everything you said and it still won't crank over so now I will go buy a starter, but where is the starter located? My bike is a 2005 cbr 1000rr., thanks Ed
Very nice video. My immobilizer light keeps flashing when I turn the key. The bike had been recently exposed to water. Any ideas ? I will try and look at the fuse this weekend.
Sounds like an ignition situation. Double check the wires are good and tight. Blow out any moisture that may have gotten in there. With water, it could be anything electrical that got wet and is now shorting.
Issue I’m having with my 2013 CBR600RR is while I’m riding my light get dim, then my check engine light comes on along with my HESD light. Bike won’t cut off at that moment but then my gear shift gauge that was added will be flashing a L and flashing the gears. After that the bike will then cut off and oil light will come on. It starts back up in 2 mins or less but it’s a dangerous thing to keep happen
Test stator, rectifier and wires. Voltage drops will cause this to happen, it's just a matter of figuring out where the issue is. Electrical issues like this can be a real bear.
so i am having a problem when im hearing a clicking noise when i click the starter but it wont start? or engine wont turn over? the guy said he just put a new starter in it but idk got a new battery in it and im not sure im check the fuse and see whats going on .
hello i have a cbr 954rr my engine starts so easily when cold but if i try to start it when hot it doesn't start engine keeps on turning though. if i jump start it it starts right away!. what might be the problem i really need yout help
@@PartzillaParts what was the other side connected to?? The positive terminal? Also could you link it or give the part number? When I look up jumper or jumper needle I just get regular jumper cables for motorcycles.
Hi, this is in the same vein as the most recent comment, regarding '05 CBR600RR. The battery now only has ~10 V, so powers the dash, lights etc, but obviously won't start the bike. When pressing the starter button, can hear the same very loud click click click (like a taser), and bike obviously won't start. Before the battery went flat, there was no clicking noise, fuel pump primed and engine cranked but no ignition. Any suggestions? Cheers, thanks
I have a 2006 Honda rr when I ride and the engine get hot and like 5 minutes after parking bike won't start and nothing is wrong with the starter and battery is good what can cause that problem
I have a 06 cbr 600 rr.. head lights come on and cluster lights up. The bike cranks but won't start over and run. It happen after I replace the front fearing
@@CV4ever2 The Honda manual says the E²-ROM in the ECM is faulty when speedo doesn't work and odometer reads "----". Replace the engine control module.
Hello I have a 2007 Honda cbr 600rr the top sensor was cut out and wired up bike was taken apart I put it back together but for some reason I can’t seem to get the fuel pump to prime for nothing or even get the bike to start can you please help me pls I need help ?
Hello. skills have Honda cbr 1000 pp 2009. I arrived at home, he drowned and the second day he did not wound up. Pat pashli diagnostics, and the diagnosis does not see the block immobilizer. Say it was your prktiku? and if that was what the problem was? Thank you in advance.
My cbr600rr powers up fine as well as my fuel pump. My battery is reading good numbers just barely under 13 volts. Now when I go to turn my bike over I get a machine gun like clicking sound from the tail of my bike I guess you could say around my seat and my gauges turn off and when I release the starter button the gauges light back up. ?? Any ideas if this sounds like a starter problem
Load test your battery. A static test isn't enough. Make sure all connections are tight and clean. If it tests good, start checking your ignition and button wires for a short.
Hi guys, I have a starter motor for a 1992 honda 250rr mc22 that is possibly spinning in reverse, what direction should a starter motor spin if the drive gear in motor is facing you.
I have a CBR600RR 2006, I replaced the starter relay but still no joy. If I jump the yellpw/red wire it cranks. What would be the next steep? Starter push bottom?
My honda 600 cbr rr 2004 just stopped while riding today. the oil lights stays on and the oil picture stays on. it cranks just wont start. just serviced a week ago
Hi, here is my problem (CB500 2002), hope you can advise something for me to solve it. I swithed the ignition ON then i pushed the starter button suddenly power cuts off (small clicking noise came, dont know where) since then no power at all. Fuse box checked, all good, main plug fuse ok too. what elso could have gone wrong? thanks!
Dude thanks for making this video but i got a question. I just bought a 2007 cbr1000rr from a friend and he hardly rides it. I dont have a multi meter but maybe i should get some. When i tried turning my bike on. So switch on kill switch is on then i click the starter. All of a sudden the screen dying out and trying to crank the engine. It will start after 3 or 4 crank. Does it mean i need a new vattery??
I have a CBR F3 95 and is blowing fuses replace the fuel and carburetor fuses and the one up under the seat where the relay when I replace the fuse it will crank up and run for a while but it will blow again and for some reason my start switch won't work so I replaced it now I'll see when I press the start button the lights will dim but it won't trigger that starter
Hi John! I followed every step in this video and my request is: Would you please make a video of how to get to the starter motor on a 2006 CBR 600rr I have taken the air box , gas tank, disconnected the negative cable that goes al the way to the starter but from that point I do not know how to disconnect the Throttle and the cables so that I can get to the thermostat and be able to reach the starter at last. I got some parts from Partzilla on the way to finish the job and I will certainly appreciate your help.
I have a 2006 cbr600rr and it all works in terms of turning on, riding, front headlights and high beams but the problem is that the indicators, horn and break lights don't work, it was working perfectly fine about 4 days ago but jst randomly stopped working today. Can anyone help on with this problem?? all the wiring have not been touched or anything it jst randomly stopped working. thanks in advance!!
Can two different casein cause the 06 600rr to not starting back when its I've check all those that you told me about and am still getting that problem
After a long winter iv decided to start it up.it turns over but it wouldn't start...I suspect the kill switch..my cbr is 2014..way to test the kill swirch?I heard the pump the first time I tried starting it..but then nothing..??!!??
I have a 2004 Yamaha YZF 600 r my problem is when starting cold it turns over then like a metal crunch then its seizes and won't turn over. it takes a while and multiple start button pushes before it starts what can that be?
hi I checked everything as you did in the video. but I when I connect the positive terminal to the yellow red stripe wire the starter does not make any noise. what could it be? starter is bad? thanks.
You might not get to this comment but i have a 2007 cbr600 and there has been a charging issue, I put it on the charger so i could take it to the shop and none of the lights turned on. I found this video and pulled out the same fuse that you did but mine was perfectly fine.. I even replaced it with the other one and still nothing lighting up on my dash. The only thing coming up is the clock and that's only when the bike is off, it's not on when I turn the bike on. Thanks and get back to me if you can
A lil late, & u probably already resolved, but I had the same issue & it was a fuse. Had installed new LED turn signals & just needed to put in a stronger fuse cuz it kept blowing the fuses. Had to ride home with no speedo, etc. 1 day... good thing I was riding locally. Lol
@@bossylady80 your good, just saw your reply but yes I did resolve it, my stator went bad which I think is common in 2007 cbrs, I had to replace the stator, regulator, and the battery because the battery stopped holding a charge
Can anyone help me with my CBR600f pgm 2003 rev counter not working speedo works indicators work temperature works just not revving after installing gear indicator
so I have a question I cleaned out my starter and tested it and it moves pretty good even from my pretty low battery that I haven't used in a couple months and so after I put everything together I checked relay fuses they're fine but the bike was making a buzzing static noise from the relay every time I pressed the power button and so I charged my battery and I could actually hear the starter Turing over but its very slow and isn't enough to power on the bike do you think that the battery can't hold a charge anymore or something? or its something else?
Would a low power for battery cause the fuel pump not to prime when engine cut off switch is flicked on and off. The ignition cranks up and the relay clicks just no prime
I bought a new battery it started no problem but after I turn it off i try turning it on again and it won't start unless I Jumpstart it even tho the battery is new
Hi I have a f1 light on and fuel pump won't prime but I'll try it again a few hours later and works fine with no f1 light and fuel pum primes. Anyone know what's going on because I dont
Ik this video is old but please for the love of god, I have a Cbr600rr 2008 model I can start my bike and ride it. but my cluster doesn’t work it shows me the indicator for my headlights and turn signals along with the clock for whatever reason but I cannot get the green neutral light. I get no rpm or speedo readings, temps, and odometer readings not that I need them but it would be useful. Your videos have taken me a long way with maintenance on bikes but can’t figure this one out :/
can anyone please help. I read the Voltage on the battery while press start button, it's 7.3V. then, I connect the multimeter to the starter it reads 5.2. Do I check all the ground cables from starter to the battery?
I have a 2007 Honda cbr 600rr that all the fuses are good on but for some reason my fuel pump will not prime and bike cranks over but won’t actually start why is that ?
I have the same problem after a low slide crash at the track. The dash lights turn on, but I'm not hearing the fuel pump activate when I turn the key to power. Bike cranks but won't start.
Really dumb question, how do I know when to get a new battery. Bought my bike used and haven't had any issues but I would like to avoid these issues too
The easiest way is to run it until there is an issue. If it's a sealed battery, there isn't much to do. If it's not, make sure the battery acid is topped off to get the most out of it. If you start getting weak starts, just toss a new one in before it dies completely.
Partzilla i also want to request this, my fuel pump doesn’t prime. When i turn my ignition i don’t hear it at all. Power switch is on (down), in neutral, kickstand up, holding clutch but i just don’t hear fuel pump priming at all so all that stuff doesn’t make a difference for me.
zodd i had changed my fairings.. turns out I’m clumsy and had my tilt sensor upside down! I felt like a complete fool after running through all my wires, testing relays, checking fuses, kill switch .. i guess i should’ve checked the most obvious things first haha
I have a 04 Honda cbr f4i and i have replaced the battery as well as the fuel pump and relays I have also replaced the ignition key the original key just turns on the fan , no fuel prime , still cranks over but no start the new key no fan when turned on no fuel prime and cranks but no start do you have any idea I have checked everything the bank angle sensor kickstand sensor you name it they all check out fine but for some reason I cant get the fuel to prime please help thanks
Did you check the harness between all those components? That sounds like best case scenario. Worst case, ECM? Check everything you can before you jump to ECM.
Johnny Trillberg, and Partzilla, I have a 2006 cbr1000rr same problem as Johnny I'll be checking all this, Johnny did you fix yours or find the problem, and is anyone aware of any recalls on this more than common issue, my. ike dose not have a diode, maybe Partzilla could do a video on this issue seeing as how it's so common
Hello I have a 01cbr600f1.won't start,new battery,Turning over, but can't hear the pump priming.any ideas where I could start looking.tried fuses,They seem ok.thanks.
I'll take that as a CBR600F4i? When you turn the key you should hear the pump prime. If not, make sure it's getting power. If power looks good, you may need to rebuild or get a new fuel pump.
Fuel pumps go out. Especially if it sat for a long time or the tank is/was dirty and debris clogs up the works. Always test the electrical to the pump before you buy a new one. Search our videos, there are 3 Fuel Pump vids on a GSXR. The process will be essentially the same.
i have honda cbr150 r india version ,i used this bike last 2 years but now battery is not working now recently i installed new battery but after five day of useing this battery it is not charging and down ,what should i do now pls tell me
Hopefully someone replies. But my 2005 Honda cbr died on me while riding randomly. Wouldn’t turn on afterwards. What do you guys think could be the problem?
My fuel pump relay under my seat is making a teaser sounds like. Ive test the charging system my stator look ok but my bike randomly dies on me. My baterry is new and spark plug replace. What else do i look for issue on my bike? I only heard it once now its working normal again im still cant ride it since its acting up.
Thank you for the informative video. This helped me. I found that my HID ballast had blown which was the reason my bike wouldnt start. I switched it out and now im back on the road.
I have the same problem what did you switch out? The bulb or starter
@@MsFshuffling did you figure it out?
You just saved somebody a BUNCH of time and money .
Boom! Two things there's never enough of! Glad to hear we could help, Dennis.
Thanks for the video, this helped me out a lot.. killed two birds with one stone .. my pump wasn’t priming , checked every single thing but didn’t work, the noticed I couldn’t start the bike just to figure out the switch was bad..
Played with the switch alittle, then the pump primed and the bike started up
About 8 years too late 😂 but still have a question for anyone. I have the same issue on my bike except it just takes a few seconds to finally start. It tries and tries and tries and sometimes I have to stop and try again but sometimes it kills the battery. I don't always have to give it gas but it seems to help sometimes.
My question is what do you think it could be?
My thoughts is either
-starter
-starter relay
-fuel pump
Only guess I have.
Thanks again 👍
Ride safe 🤙
Great video! One thing that confused me at first was when you were testing the starter relay. The video shows you had the wiring harness disconnected but doesn't show you re-connecting it. This made me question whether the wiring harness was to pass power from switch or to the starter.
Also, the camera angle doesn't clearly show the actual removal of the power cable from the relay (I guess it can be inferred by your hand movements). But seeing the beefy relay terminals with my own eyes is what made it obvious that's what the starter is connected to.
What did you use to bypass the switch? To complete the circuit
When I put the clutch in the gear of my Honda MC22 RR bike, the neutral bulb lights up, I replaced the diode but the problem is the same, thank you for providing a solution
Nice video my 2004 rr wont start when hot could it b the starter?
I have a 2006 honda cbr 600rr. An I just ordered a starter solenoid hopefully it will start now.. an also have a brand new battery 3weeks ago..if it doesn't start after this what else do I need to look at?
Wiring for damage or corrosion
Great tutorial John helped diagnose my problem!
So much expertise. Nice and concise. Always helpful
Thanks for the video!
Question for you I'd you get time.
I've done all the steps and bike still won't start, I removed starter motor and attached positive and negative to it and it fired straight up but won't start the bike. Can the start be to weak to move the engine or is it likely something else?
Please do a fuel pump problem video!! The two clips that connect to the pump (black goes to the sensor and brown goes to the pump) I use a volt meter on the black and it has 10.56 volts and the brown has 0.00... the cords look to be fine and relays and fuse are not blown...any suggestions😫 fuel pump was on a tank that has been sitting for a long time gas smelled like varnish. Cleaned the tank and changed the pump inside it, but not the whole entire fuel pump. Fuel pump wont prime.. please help
Thanks for the video.
So I started the bike by bipassing starter button and it did work.
Does that mean i do have a problem with my button? Or wires i suppose.
Thank you.
I have the same question lol I sent 12 volts to the red/yellow wire that goes into the starter solenoid and it fired right up. Did you figure it out?
@@williamreilly4676 Not yet but will start by replacing the relays as I also have a problem with my headlights, low beam isn't working and high beam I can't even switch off.
I might even try to open the button and see if it's not malfunctioned.
Will post here if I solve the problem.
@@ArturK1M after I commented this I tested the wires, no power. So i opened up the kill switch/start button, cleaned the contacts, then tested it again, still no power. Chased wires all the way to solenoid and all seemed fine, ended up peeling back the heat shrink/protective sleeve right below the kill switch and two of the wires were pinched clean in half 🤦🏻♂️ I'm going to splice them and see if it works today. 99% positive it was the issue
@@williamreilly4676 The first connector coming from steering bar under right fairing below tank cover. That was the problem, I literally just touched it and tge bije fired up. Either dirty, loose cable or snapped wire. Let's see, all I did is clean it so far.. Thanks for good conversation!
I bet the service manual for most bikes tells you how to test the internals of a starter too. Under electrical system / starter motor inspection. There should be continuity between armature segments. There should be no continuity between an armature segment and the shaft. Careful, because I measured some continuity that turned out to be my skin.
so a fuse blows when too much power surges so its protected?
If there's a short in something like the starter, the fuse blows, so the wires don't melt.
Do you have a replacing the starter video?
Your videos are the best. Quick question. I have a 2006 CBR 600rr, she cuts off every time I stop at a light and I have to turn it back on. Sometimes I have to pop start it in 2nd gear after changing out battery and spark plug. Haven't checked the stator but I feel thats what the issue is
Test your regulator first. Sometimes, it gets hot and just shuts the motor off. It's better to test the components than just blindly replace. You'll save some money.
Partzilla thank you, I will be sure to start there.. I'll let you know how it turns out.
the first thing was what rectified my issue, thanks mate 👍
Thank you! This just happened to my Cbr F2 600. Won’t crank seems power is drained and shortage of circuit power.. I believe the stator rectifier is the issue ..
Run the tests before you start buying parts!
Yes of course! Battery gets charge. Starting bike and running, but bike now gets hot now too soon..
If it's running too lean you will have issues starting and it will get hot quick. Might be something to consider as well.
Yes of course. Seems like its not getting much water from the pump... Another fan would be nice too
very complete and full of knowledge
My cbr 600rr 2008 sometimes hard starts when warm
Cranks good but doesent fire up only when its hot
I have to crank it two times to fire up
Any clue?
Battery good
Life saver brother 🍺
Hey for a 03 cbr600rr
New battery in it. Intermittently slow cranking. Only once its warm. Slow crank and dies u can hear the starter go click click click really fast.
Well, just because it's new doesn't mean it's good. Do a load test on it.
I'm so amazed that I can't find not a single video of a 2007 cbr600rr....
Any chance you’d do a video about if the motor turns over but nothing else happens ? I’m currently in that situation and after about a month of searching someone mentioned that my tip over sensor could be bad/burnt out ? Have an 05 cbr600rr and it seems most of what you do goes for that as well
Any tricks to help pull off the cover of the main fuse?? Mine seems to be very difficult..
Hello, got a 09 honda cbr 600, they guy said something about the previous owner did something with the headlights and now the bike wont start, it turns over but wont start, says it needs and ignition, but before i buy anything was hoping for feedback. I was going to just hot wire it but he said that it would mess up the cpu or something i dont know…😭
So when that main fuse was blown will the clock on the gauge cluster still work? Because mine the clock is on, the battery is brand new and as soon as I turn the key there’s nothing on the gauge cluster at all
If you hear a loud screech while riding and then when you slow down the engine cuts off and and won't start again, you smell a faint burning smell and your battery is good you most likely need to replace the starter, correct?
I learned a lot from this video thank you very much
What happens if you complete the circuit by using your method and the bike starts? What would be my issue? Currently where I'm at. Replaced the solenoid did not solve it
I have an 09green and black 600rr! my bikie shut off on me at a stop light after getting gas, the bike did sit for about 2 months here in pa from november through december
I having trouble on separating plug on the stater rely to check the fuse
Hello I own a 2007 cbr600rr I have a problem with my headlights that my high beams work but my low beams don't turn on. The bulb is fine. Another thing I thought about checking is the relay, I just can't figure out how to get the headlight relay out to check it. Is it just a pull out? Or is there like a clip holding it in? I checked the fuse, it's fine.
Thanks for your video....i did everything you said and it still won't crank over so now I will go buy a starter, but where is the starter located? My bike is a 2005 cbr 1000rr., thanks Ed
Should be right side, just under frame. To access the entire thing, you will have to remove the tank.
Very nice video. My immobilizer light keeps flashing when I turn the key. The bike had been recently exposed to water. Any ideas ? I will try and look at the fuse this weekend.
Sounds like an ignition situation. Double check the wires are good and tight. Blow out any moisture that may have gotten in there. With water, it could be anything electrical that got wet and is now shorting.
Issue I’m having with my 2013 CBR600RR is while I’m riding my light get dim, then my check engine light comes on along with my HESD light. Bike won’t cut off at that moment but then my gear shift gauge that was added will be flashing a L and flashing the gears. After that the bike will then cut off and oil light will come on. It starts back up in 2 mins or less but it’s a dangerous thing to keep happen
Test stator, rectifier and wires. Voltage drops will cause this to happen, it's just a matter of figuring out where the issue is. Electrical issues like this can be a real bear.
so i am having a problem when im hearing a clicking noise when i click the starter but it wont start? or engine wont turn over? the guy said he just put a new starter in it but idk got a new battery in it and im not sure im check the fuse and see whats going on .
hello i have a cbr 954rr my engine starts so easily when cold but if i try to start it when hot it doesn't start engine keeps on turning though. if i jump start it it starts right away!. what might be the problem i really need yout help
Test your regulator rectifier. When they start to go bad, heat affects the component.
What is that tool he used to start the bike manually by inserting the metal tip into the wire?
It is called a jumper.
@@PartzillaParts what was the other side connected to?? The positive terminal?
Also could you link it or give the part number? When I look up jumper or jumper needle I just get regular jumper cables for motorcycles.
Hi, this is in the same vein as the most recent comment, regarding '05 CBR600RR. The battery now only has ~10 V, so powers the dash, lights etc, but obviously won't start the bike. When pressing the starter button, can hear the same very loud click click click (like a taser), and bike obviously won't start. Before the battery went flat, there was no clicking noise, fuel pump primed and engine cranked but no ignition. Any suggestions? Cheers, thanks
It will click like that when it has insufficient power. As for the initial issue, check you are getting fuel and spark...check plugs and coils.
How did u manage to pull it out so easily
I have a 2006 Honda rr when I ride and the engine get hot and like 5 minutes after parking bike won't start and nothing is wrong with the starter and battery is good what can cause that problem
Regulator Rectifier. Test when hot to confirm.
@@PartzillaParts please can you send of it looks like please am just getting into big bike
The regulator rectifier
I need the starter relay but can’t find it on website
I have a 06 cbr 600 rr.. head lights come on and cluster lights up. The bike cranks but won't start over and run. It happen after I replace the front fearing
What tool did you use to complete the circuit?
What I used is an alligator clip and a metal T Pin
Great tip! Fixed my problem, thank you :)
I have a Honda cbr600 rr 2004
And it’s not showing how many km / mile the engine got also the miles per hours is showing zero.
Any solution on that ?
Generally a new cluster.
Partzilla i bought 2 brand new cluster but I still have the same problem
I will send you a video to show u exactly what happens
@@CV4ever2 The Honda manual says the E²-ROM in the ECM is faulty when speedo doesn't work and odometer reads "----". Replace the engine control module.
Corey Regan thanks for your help
I already did that and it worked perfectly
Hello I have a 2007 Honda cbr 600rr the top sensor was cut out and wired up bike was taken apart I put it back together but for some reason I can’t seem to get the fuel pump to prime for nothing or even get the bike to start can you please help me pls I need help ?
Hello. skills have Honda cbr 1000 pp 2009. I arrived at home, he drowned and the second day he did not wound up.
Pat pashli diagnostics, and the diagnosis does not see the block immobilizer.
Say it was your prktiku? and if that was what the problem was?
Thank you in advance.
thank you very much for the absolutely useful and very interesting videos you are making there !!!
My cbr600rr powers up fine as well as my fuel pump. My battery is reading good numbers just barely under 13 volts. Now when I go to turn my bike over I get a machine gun like clicking sound from the tail of my bike I guess you could say around my seat and my gauges turn off and when I release the starter button the gauges light back up. ?? Any ideas if this sounds like a starter problem
Load test your battery. A static test isn't enough. Make sure all connections are tight and clean. If it tests good, start checking your ignition and button wires for a short.
Hi guys,
I have a starter motor for a 1992 honda 250rr mc22 that is possibly spinning in reverse, what direction should a starter motor spin if the drive gear in motor is facing you.
I have a CBR600RR 2006, I replaced the starter relay but still no joy. If I jump the yellpw/red wire it cranks. What would be the next steep? Starter push bottom?
Could be the switch, or a bad wire.
Would this be the same.for a.08 cbr 1000rr? Relay issue with headlight. Turn on bike, it turns on but does not stay on...
My 08 cbr600rr is sputtering on low rpms 7k blow any reason why? I have no clue
My honda 600 cbr rr 2004 just stopped while riding today. the oil lights stays on and the oil picture stays on. it cranks just wont start. just serviced a week ago
I have a problem I turn on the my bike which is 1998 cbr 900rr all fluids and gas once I hit the start button just a clicking noise please help
Hi, here is my problem (CB500 2002), hope you can advise something for me to solve it. I swithed the ignition ON then i pushed the starter button suddenly power cuts off (small clicking noise came, dont know where) since then no power at all. Fuse box checked, all good, main plug fuse ok too. what elso could have gone wrong? thanks!
Hello hegedustamas3
Did you by chance check the voltage of the battery? this sounds like it could be a weak battery. Hope this helps!
Dude thanks for making this video but i got a question. I just bought a 2007 cbr1000rr from a friend and he hardly rides it. I dont have a multi meter but maybe i should get some. When i tried turning my bike on. So switch on kill switch is on then i click the starter. All of a sudden the screen dying out and trying to crank the engine. It will start after 3 or 4 crank. Does it mean i need a new vattery??
Start with simple first. Health test the battery or get a new one. You can't do accurate tests without a good battery anyway.
There is no OBDII on 2008 model?
Can you tell me plz? What should i know? Before buy a motor that someone use already. Plz tell me. Thank you.
That's a long conversation, Kim. Was there something specific you want to know?
@@PartzillaParts i just want to know a little point before buy motor. Can you tell me?
M.r john i have honda cbr 1000 rr 2007 i have a problem weth it is after 5 .6 Rpm go fast to the top Rpm but the bike not exsleritng
I have a CBR F3 95 and is blowing fuses replace the fuel and carburetor fuses and the one up under the seat where the relay when I replace the fuse it will crank up and run for a while but it will blow again and for some reason my start switch won't work so I replaced it now I'll see when I press the start button the lights will dim but it won't trigger that starter
Check your wiring from ignition and switch, you likely have a short somewhere.
Had a question , my 929 shut off and dash lights shut off simotaniously and blown a fuse , and keep blowing the 30 amp fuse , and 2ont start
What indicates bad spark plugs? Thx.
They don't spark.
Afraid I may need a new starter. Do you have a video for replacing one. I get a hum from my relay even after I replaced it.
It's on the list, but the video has not been done yet.
Hi John! I followed every step in this video and my request is: Would you please make a video of how to get to the starter motor on a 2006 CBR 600rr I have taken the air box , gas tank, disconnected the negative cable that goes al the way to the starter but from that point I do not know how to disconnect the Throttle and the cables so that I can get to the thermostat and be able to reach the starter at last. I got some parts from Partzilla on the way to finish the job and I will certainly appreciate your help.
I have a 2006 cbr600rr and it all works in terms of turning on, riding, front headlights and high beams but the problem is that the indicators, horn and break lights don't work, it was working perfectly fine about 4 days ago but jst randomly stopped working today. Can anyone help on with this problem?? all the wiring have not been touched or anything it jst randomly stopped working.
thanks in advance!!
Can two different casein cause the 06 600rr to not starting back when its I've check all those that you told me about and am still getting that problem
After a long winter iv decided to start it up.it turns over but it wouldn't start...I suspect the kill switch..my cbr is 2014..way to test the kill swirch?I heard the pump the first time I tried starting it..but then nothing..??!!??
you can test for spark. Otherwise it's almost always a fuel issue. Filter, lines, etc.
I have a 2004 Yamaha YZF 600 r my problem is when starting cold it turns over then like a metal crunch then its seizes and won't turn over. it takes a while and multiple start button pushes before it starts what can that be?
Also check the 20 amp head light fuse
It stops the starter
my 2008 honda cbr 1000rr does not start because no spark coming through. Where should I turn to fix that problem?
hi I checked everything as you did in the video. but I when I connect the positive terminal to the yellow red stripe wire the starter does not make any noise. what could it be? starter is bad?
thanks.
You might not get to this comment but i have a 2007 cbr600 and there has been a charging issue, I put it on the charger so i could take it to the shop and none of the lights turned on. I found this video and pulled out the same fuse that you did but mine was perfectly fine.. I even replaced it with the other one and still nothing lighting up on my dash. The only thing coming up is the clock and that's only when the bike is off, it's not on when I turn the bike on. Thanks and get back to me if you can
A lil late, & u probably already resolved, but I had the same issue & it was a fuse. Had installed new LED turn signals & just needed to put in a stronger fuse cuz it kept blowing the fuses. Had to ride home with no speedo, etc. 1 day... good thing I was riding locally. Lol
@@bossylady80 your good, just saw your reply but yes I did resolve it, my stator went bad which I think is common in 2007 cbrs, I had to replace the stator, regulator, and the battery because the battery stopped holding a charge
Can anyone help me with my CBR600f pgm 2003 rev counter not working speedo works indicators work temperature works just not revving after installing gear indicator
so I have a question I cleaned out my starter and tested it and it moves pretty good even from my pretty low battery that I haven't used in a couple months and so after I put everything together I checked relay fuses they're fine but the bike was making a buzzing static noise from the relay every time I pressed the power button and so I charged my battery and I could actually hear the starter Turing over but its very slow and isn't enough to power on the bike do you think that the battery can't hold a charge anymore or something? or its something else?
Hello Aleksey. What you are describing sounds a lot like a dead battery. That is the first thing i would check.
Would a low power for battery cause the fuel pump not to prime when engine cut off switch is flicked on and off. The ignition cranks up and the relay clicks just no prime
If it's dead. It doesn't require much to prime the pump.
I have the same problem relay click, ignition work and kill switch work and pomp no prime did you resolve the problem in your bike?
I bought a new battery it started no problem but after I turn it off i try turning it on again and it won't start unless I Jumpstart it even tho the battery is new
Great video. Thank you.
Hi I have a f1 light on and fuel pump won't prime but I'll try it again a few hours later and works fine with no f1 light and fuel pum primes. Anyone know what's going on because I dont
It would be great if y'all can make a video of the real electrical problems these bikes have.
Well, you might have to narrow down the "real" electrical problems and we can try to put something together.
Ik this video is old but please for the love of god, I have a Cbr600rr 2008 model I can start my bike and ride it. but my cluster doesn’t work it shows me the indicator for my headlights and turn signals along with the clock for whatever reason but I cannot get the green neutral light. I get no rpm or speedo readings, temps, and odometer readings not that I need them but it would be useful. Your videos have taken me a long way with maintenance on bikes but can’t figure this one out :/
can anyone please help. I read the Voltage on the battery while press start button, it's 7.3V. then, I connect the multimeter to the starter it reads 5.2. Do I check all the ground cables from starter to the battery?
Hello Do it Diep. How many volts are you getting without pressing the start button?
Partzilla it was 12.6V
What you are describing to me would tell me that you need to replace your battery.
I have a 2007 Honda cbr 600rr that all the fuses are good on but for some reason my fuel pump will not prime and bike cranks over but won’t actually start why is that ?
I have the same problem after a low slide crash at the track. The dash lights turn on, but I'm not hearing the fuel pump activate when I turn the key to power. Bike cranks but won't start.
Trying to do my self don't have money to take to the shop
I rode my 05 cbr 600 rr yesterday on the highway and then it started jerking then it shuts off and on. What do you think is wrong ?
To little info to really tell. Could be fuel or spark.
Really dumb question, how do I know when to get a new battery. Bought my bike used and haven't had any issues but I would like to avoid these issues too
The easiest way is to run it until there is an issue. If it's a sealed battery, there isn't much to do. If it's not, make sure the battery acid is topped off to get the most out of it. If you start getting weak starts, just toss a new one in before it dies completely.
+ Partzilla
could u do video on fuel prime pump troubleshooting on cbr600, thank you!!
We'll add it to the list!
Partzilla i also want to request this, my fuel pump doesn’t prime. When i turn my ignition i don’t hear it at all. Power switch is on (down), in neutral, kickstand up, holding clutch but i just don’t hear fuel pump priming at all so all that stuff doesn’t make a difference for me.
try to turn on n off kill switch for 10 times, works for me, i think they maybe dirts inside that may interfering it
zodd i had changed my fairings.. turns out I’m clumsy and had my tilt sensor upside down! I felt like a complete fool after running through all my wires, testing relays, checking fuses, kill switch .. i guess i should’ve checked the most obvious things first haha
i overcheck everything too since my bike doesnt start, even thinking to do this th-cam.com/video/oaixZVeusv4/w-d-xo.html
How I can regulate my rpm on 2008 cbr 600r? I cannot found the idle adjuster
I have a 04 Honda cbr f4i and i have replaced the battery as well as the fuel pump and relays I have also replaced the ignition key the original key just turns on the fan , no fuel prime , still cranks over but no start the new key no fan when turned on no fuel prime and cranks but no start do you have any idea I have checked everything the bank angle sensor kickstand sensor you name it they all check out fine but for some reason I cant get the fuel to prime please help thanks
Did you check the harness between all those components? That sounds like best case scenario. Worst case, ECM? Check everything you can before you jump to ECM.
Johnny Trillberg, and Partzilla, I have a 2006 cbr1000rr same problem as Johnny I'll be checking all this, Johnny did you fix yours or find the problem, and is anyone aware of any recalls on this more than common issue, my. ike dose not have a diode, maybe Partzilla could do a video on this issue seeing as how it's so common
Gracias hermano , ya prendió mi moto
No es tu hermano…..
Es tu padre …..
Brilliant video
Hello I have a 01cbr600f1.won't start,new battery,Turning over, but can't hear the pump priming.any ideas where I could start looking.tried fuses,They seem ok.thanks.
I'll take that as a CBR600F4i? When you turn the key you should hear the pump prime. If not, make sure it's getting power. If power looks good, you may need to rebuild or get a new fuel pump.
Thanks for the reply.but do you think that it could be something else, before I go getting a new fuel pump.do they give trouble.
Fuel pumps go out. Especially if it sat for a long time or the tank is/was dirty and debris clogs up the works. Always test the electrical to the pump before you buy a new one.
Search our videos, there are 3 Fuel Pump vids on a GSXR. The process will be essentially the same.
i have honda cbr150 r india version ,i used this bike last 2 years but now battery is not working now recently i installed new battery but after five day of useing this battery it is not charging and down ,what should i do now pls tell me
Get a new battery, make sure it's full of distilled water, fully charge it, then try again.
Hopefully someone replies. But my 2005 Honda cbr died on me while riding randomly. Wouldn’t turn on afterwards. What do you guys think could be the problem?
It could be a number of issues. Test to see if you are losing spark or fuel. That is the first step.
@Partzilla how do you adjust the throttle idle I can't seem to find it
There is no manual adjustment on this unit.
Thanks for getting bk to me
Mine keeps melting the fuse. New relay stater rec. ?
My fuel pump relay under my seat is making a teaser sounds like. Ive test the charging system my stator look ok but my bike randomly dies on me. My baterry is new and spark plug replace. What else do i look for issue on my bike? I only heard it once now its working normal again im still cant ride it since its acting up.
Test the regulator rectifier first, just to cover the charging system.
Motorum honda cbr 600 rr. F1 arızası var ne yapmalıyım