Build an Arduino Radio Transmitter & Receiver for RC Aircraft & Vehicles
ฝัง
- เผยแพร่เมื่อ 15 พ.ค. 2024
- Hey everyone! In this video, you get to build your own Arduino-based (up to 7-CH) Hobby-grade Radio Transmitter and Receiver/Controller pair from scratch with NRF24L01 for any RC Models such as cars, boats, planes, and even drones. Closer to the end of the video, you see how a robot car is controlled with this homemade Radio control setup!
Code credits to Electronoobs for the TX and RX code - Original Project Vdeo - • DIY Radio Controller -...
----------------------------------------------------------------------
👉 Visit my online Storefront: sites.google.com/view/maximag...
----------------------------------------------------------------------
☕ Buy me a coffee: www.buymeacoffee.com/MaxImagi...
----------------------------------------------------------------------
Instagram: @max.imagination - max.imagina...
Instructables page: www.instructables.com/member/...
----------------------------------------------------------------------
Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!
Link to a website with good info on the NRF24L01 Radio Transceiver module:
lastminuteengineers.com/nrf24...
Downloadable Circuit Diagrams for TX and RX:
drive.google.com/drive/folder...
Transmitter and receiver codes (CODE CREDITS: @ELECTRONOOBS ):
drive.google.com/drive/folder...
Transmitter's cardboard case - sketches/blueprints:
drive.google.com/file/d/10CfK...
Transmitter and receiver codes for L298 Driven RC Arduino robot car:
drive.google.com/drive/folder...
Things needed for this project (with purchase links):
(x2) NRF24L01 + PA/LNA with antenna - amzn.to/3EGRQYe
(x2) Arduino Nano - amzn.to/3rXevrK
(x2) Joystick Module - amzn.to/3EI9HOB
(x2) Large and small perforated prototyping PCB board for transmitter and receiver - amzn.to/3Vryxs2
(x1) On/off switch - amzn.to/3evOlcv
(x2) 25V 10mf capacitor - amzn.to/3Tia32k
Female and male pin headers (for Arduino Nano) - amzn.to/3EMol7s
(x1) Male and female JST connector pair - amzn.to/3CCCp0v
(x2) 18650 Li-Ion 3.7V battery cell - amzn.to/3zp86JQ
(x1) 3 pin 2 cell battery connector for charging and charger - amzn.to/3CzrRPY, amzn.to/3ev5yD5
(x1) 22 Gauge 0.64mm roll of bare copper wire - amzn.to/3Czs6KS
Thin connecting wires - amzn.to/3TkqMCi
Cardboard sheet
Clear plastic container lid
🪛🔧🔨 Tools and extra supplies I use:
➡️ Soldering Iron Kit - amzn.to/3X6L5Wq
➡️ Hot Glue Gun - amzn.to/3E6trJG
➡️ Drill Machine - amzn.to/3EDe0u8
➡️ Box cutter/Utility knife - amzn.to/3hP9MGI
➡️ X-Acto Hobby Knife - amzn.to/3XbL7ML
➡️ Cutting Matt (Green) - amzn.to/3gil71A
➡️ Needle-nose Pliers - amzn.to/3ECTKc3
➡️ Wire Cutters for Electronics - amzn.to/3ECut1B
➡️ Wire-stripping tool (Automatic) - amzn.to/3hQsMVD
➡️ Screwdriver kit - amzn.to/3V6vgNX
➡️ Heat-shrink Tube Kit - amzn.to/3AksTPE
➡️ Jumper Wire Kit - amzn.to/3UGhMZq
➡️ Breadboard for Prototyping - amzn.to/3GlF4ze
➡️ Perf Boards, Pin headers, and Connectors Kit - amzn.to/3AkySUw
➡️ Superglue - amzn.to/3EE6uis
➡️ Duct Tape - amzn.to/3g5mTU0
➡️ Double-sided Tape - amzn.to/3Edta82
➡️ Kapton Tape (for battery leads) - amzn.to/3X58bNl
tags:
max imagination, transmitter and receiver, arduino transmitter, arduino based transmitter, rc transmitter, nrf24l01, radio controller, DIY,NRF24L01, Remote Control, Arduino-Based, NRF24L01 Tutorial, Arduino RC Transmitter, Arduino RC Receiver, DIY Radio Controller, DIY Transmitter, DIY Receiver, NRF24L01 Transmitter, NRF24L01 Receiver, Arduino Radio Transmitter, Arduino Radio Receiver, Arduino Wireless Transmitter, Arduino Wireless Receiver, Arduino NRF24L01 Tutorial, NRF24L01 Wireless Control, Build Your Own RC Transmitter, NRF24L01 Radio Transmitter, RC Transmitter Receiver DIY, DIY Arduino RC Control, NRF24L01 Radio Receiver, NRF24L01 RC Transmitter, Arduino Wireless Transmitter Receiver, DIY RC Transmitter Receiver System
#arduinoproject #rctransmitter #remotecontrol - วิทยาศาสตร์และเทคโนโลยี
Hey everyone! The comment section has finally been re-enabled over the whole channel after 2 years by TH-cam themselves who shut it down in the first place. Glad to be in touch with my viewers again! :)
hey max i sent you a message on instructibles i love your videos.
@@danielkessler662 Hey! Thank you! Will check your message soon ✌🏻
@max imagination thanks for responding on here
Can i use arduino uno for tranmmiter and arduino nano for receiver
@@bouncypixiegamers76 Yes, you may.
the video i have been looking for for years thank you very much for this video please continue this work
Sure thing! Thanks for your comment! 😀👍
This is the full detailed video, thanks MAX sir :)
Glad it was helpful! Thanks for commenting :)
What is your transmitter and receiver programming app or application
I like your homemade transmeter and reciever
Thx thx greatest tutorial on TH-cam ! You made it so easy to make thx ☺
Thanks a lot for your comment! 😀
Thanks for sharing this video and information
Thanks for great video, so the NRF24L01 works as Transmitter & Receiver, that is great. Now i just need 2 of those :)
Glad to hear my video has helped. Cheers! ✌
I searched many videos on youtube but this one is the best in designe and simple explatation and explained how to add more channel for future use :D
I'm really glad that you found it useful! Thanks 😊✌
Thanks so much!
Wow it's really amazing
Thanks for your support!
Thanks 🙏🏼, since 15 days I was looking for this
No problem! I'm glad I was able to help you with my video tutorial :D
Cheers
@@MaxImagination a question please, are the codes for transmitter and those of the drone receivers same ? Because the pins are not same. Could I get codes ?
@@lampfall7915 Hi, sorry for the late reply. Not exactly, they are two different codes, as the first code shown for the transmitter and the receiver are for an airplane, which has completely different controls. You'd need to search a site such as GitHub to find the right matching code that allows you to control a homemade drone with this NRF24 Transmitter.
Cheers!
@@MaxImagination thanks so much
@@lampfall7915 No problem! :)
Amazing, I have all the parts at arm's reach! that has to be a first for me.
The only bit I'm a bit dubious on is running the NRF modules from the Nano's regulator, I've found these to be quite fragile and easy to kill.
Great! About the NRF modules, if you have doubts using the Nano's regulator, try using a separate "AMS1117 3.3V" regulator each to power the transceivers with.
Now I will make my own Rc transmitter and receiver thanks
Thanks for watching, I'm glad you chose my tutorial to follow :)
You teached me a lesson is capacitor, thank you.
Glad that helped! Cheers.
ive built the transmitter and reciever but ive downloaded the code and its not working idk if the code is correct or not but is there anything i can do to check it
Hi there. Be sure to carefully check and troubleshoot your wiring that it goes along whats on the diagrams and that your boards are getting sufficient power. Check that you've typed in the correct Arduino board pins in the code for both the Transmitter and Receiver. Just a couple of important things to take note of when checking for what can be wrong.
Cheers,
Max
Helpful tutorial!
Thank you! :D
Hey! Max you are a good guy
This video is very knowledgeable
Thank you
Thanks a lot for your kind compliments!
@@MaxImagination question how big are the pcb boards?
@@oscarc624 I used (x2) 7x9cm Perforated Printed Circuit Boards.
@@MaxImagination is a 9x15 one ok
@@MaxImagination also would it be ok if I use a Arduino mega instead of a micro one
This is just what I needed.. thank you for the free code...
I hope u get loads of subs...
I'm very pleased you're pleased... thank you!
@@MaxImagination hey max, can we use this code for drone
Great work
Thank you! Cheers!
THANK YOU
Thanks so much
Bruh how does this guy not have at least 100k subs?
And he deserves a million❤❤
Fantastic max, my son is 10
years old, he is crazy on these stuffs.
Are u taking any online sessions.
If no u should start to share ur skill set, and this will bring exponential max to this universe.
Great job, be healthy to do more like good work
Hi there! Thanks for your comment. I usually don't provide 1 on 1 sessions as I mostly spend my time on managing the current work that I do here. Will keep it up. Cheers!
@@MaxImagination thank you for kind consideration, max
For ten years old, this transmitter is suitable.
Very useful video! Keep up the great work
Nrf projects never worked for me 😢
But atleast this video works for others
Thank you 😊
Thank you! Will do...
Have you identified the core issue with your NRF transmitter?
Don't give up... You can do it!
@@MaxImagination I can't find the issue till now 😞
I suggest you search for NRF24L01 tutorials on youtube to clarifiy the issue you have. Perhaps you can look on troubleshooting forums and try a list of different methods to solve your problem. Keep trying.
thanks bro after a 4to 5 tray it worked becous of library
You're welcome!
Great video. You should learn about BMS for your li-ion batteries to be safer and get more time out of them.
Thanks. I am aware of the importance to using a BMS in 2+ S series battery configurations. This controller's battery didn't get one as the charger is a 3-wire one with a built in bms board to balance charge.
Thank you
wow wow max max ++ credit
Thank you 🎉
You’re welcome 😊
Reorient. ReorientATE is not a word. Your videos are great, keep it up. Subed.
I heard the British say reorientATE, anyway, you've got that one right! Thanks again, John!
@@MaxImagination no problem. I want your channel to do very well. You're doing great things that beginners can copy. Your tutorial and explanations are excellent. I've been sharing your channel to the electronics and science minded teachers (for clubs) and parents in our ISD. Living next to NASA we have a lot of fellow geeks😁. Keep it up.
Wow what a man bro
Please make a drone fully controlled using arduino 👍😃😃😃
Thanks for commenting!
Might make one in the near future 😃
Hii..max 😊.... thankyou for this ...ia am trying to do one for my self thankyou lot 😅
Hi there. All the best!
@@MaxImagination 😀 thanks bro 😊
This is so cool. Do you know if the transmitter will work between boards? Arduino namo and a pi pico for example?
Hi. Good question. I have never tried using the RPI Pico in a project before. You may need to research that board with NRF24L01 communication a bit more.
Nice
Hey max, May I know the the size of the wires you use to solder the batteries together and any other wires you used other than the 30 Gauge wires you have listed in the video. Thank you so much.
Hi there. I used 20-gauge (20AWG) Wires for wiring the battery. I typically use 24AWG wires for my circuits which are a bit thinner. Cheers.
@@MaxImagination Did you use the 24-gauge wires to wire all of the circuits in the video along with the few times you used the 20-gauge wires and the 22-Gauge copper wire?
Can I use 22-gauge wires instead of the 20-gauge for the circuit and battery or will cause some issues?
Also is it possible to use a stripped down solid core 22-gauge wire instead of the copper wire?
Hi Max, I'm your new subscriber. i love the build, may I ask the range of the transmitter to the receiver? I want to build one for myself.
Hi Glenn, thanks for watching! Depending on how well you've got the power to the transceiver modules filtered, range can go up to 1KM.
Is the 3.3V voltage regulator mandatory since the arduino nano has both the 3.3V pin and the 5V pin so it can be conected to the nrf module and all the servos or motors.
Not mandatory, but recommended for a more reliable supply. I suggest placing a 10 microfarad capacitor for power ripple filtering at the power terminals of the radio module if you're powering it from the Arduino's 3.3V supply.
Hi there! I've made this for 2 DC motors but I need them to work separately (I am making an RC car). The code that I downloaded from you makes them work at the same time, what can I do?
Hi there. Be sure to run them with separate ESC's/motor drivers and use different channels for each.
Hello bro, loved your work and got inspired to try it myself, but I ran into a problem like my receiver is working fine if I am powering my Arduino nano from my laptop, but when I am powering the receiver circuit with 7.4V battery it is not working instead I am getting power drop. Please can you help me out 😊
Hey and thanks! Be sure to power your Arduino via the "VIN" pin with 7.4V and not the tranceiver module that receiver/transmits data, otherwise you'd have fried it.
Great project 👍.I want to make rc plane.can i use 2 serial connected 18650 lithium iron batterys to get 7.4v for receiver instead of lithium polymer battery for rc plane?
Hi and thanks! Yes, you may do that, but make sure you're building your plane with highly efficient motors - brushless motors to have enough power for the plane to lift off with the heavier Lithium Ion batteries.
@@MaxImagination thanks 👍
Liked
Hi Max, will the stearing mechanism work if I use a motor instead of a servo?
Hi Akram, good day! If you're referring to the steering mechanism from my previous video, yes. A standard small DC motor will work as that's what it was built for.
Though, if you are referring to using the transmitter and receiver/controller similar to the one I made in this video, I'd highly recommend using a servo motor for the steering.
Have a good week!
- Max.
Hey! I have a little question about the 8 channel receiver and transmitter tutorial, in it, the guy shows a schematic and on it he shows that the 5v line of the joysticks are connected to each other with no connection to the arduino 5v or the nrf 5v module but the ground is connected to th nrf’s ground. How will the joysticks work with no actual 5v power?
Hi! I just checked the same diagram you were pointing out about, I saw that it was actually the guy's mistake not connecting the joy sticks. So yes, do connect the joy stick's 5V lines to the arduino's 5V.
Cheers ✌
To answer your question, no, the joysticks won't work without being connected to 5v
Thanks so much!
Hi max, I love the build.May I ask something,How to control 4-DC motors and 2-servo motor? Without ESC. Can you please say once🥺🥺
Hi there. Thanks! The servo motors do not require an ESC to run but the motors need some form of motor driver whether be an H-bridge or just a simple MOSFET.
@@MaxImagination Thank you max!
@@MaxImagination I have a Doubt in Transmitter we connects D11 to MOSI But In Receiver we connects D11 servo motor. Is That actually works??
One more thing if you don't mind..
Can I on tx attach the push button pin (sw) from one of my joysticks to ch5 or ch6 as a digital read?.
Then on rx solder a rc on/off switch I bought from ebay and have the push button on tx activate it?
I have hooked it up but nothing happens.
Push button on stick is digital right?.
Hi there. Yes, you may do so.
About the RX's ON/OFF switch, I don't quite understand what you meant by that... Do you mean you want to activate the RX remotely?
Also yes, the Joystick's built-in push button should be hooked up digitally. Cheers.
Please advise for the maximum distance could the receiver respond to the Transmitter. Thanks
They say it can transmit up to 1km with perfect conditions & decent power supply.
Cheers!
What is the maximoum range of the transmiter
1KM, if tuned correctly.
Halo MAX BRO😊😊😇😇😇😇💕💕💕💕
You're so super😇😇❤️❤️❤️❤️❤️ I like it 💕💕💕💕💕💕💕💕💕💕
Thank you for tuning in 😀
can i use arduino mega to make the controller and the nano on the vehicle?
Yes.
can we use a simple rocker switch instead of that one for the transmitter??
Yes. Any on/off switch with a higher current value than 0.5A will work.
He podido medir el alcance de los nrf24l01 con lna y casi llega los 2.6km. Y digo casi por qué se me atravesó un puente vial en mi ciudad. Solo que traen una pequeña falla con el puerto spi. Se requiere una resistencia entre MISO y los 3.3v
Very good. What value resistor do you need for that?
@@MaxImagination Aproximadamente entre 2.2K y 2.7K . ¿Has podido detectar esa falla en la comunicación que menciono?
One more doubt brother, which channel ESC should be connected in ur circuit and code?
If you're using a PWM ESC, keep in mind that it can be connected to any channel above the 1st one (first one or two channels are PPM, not PWM channel).
Hey Max !! Can I use it for making an rc plane ?? Using BLDC motor
As mentioned in the video, yes. Even with a brushless DC motor
@@MaxImagination Thank you I made it now tomorrow I will go to test it in park
hello, thanks for this video i made the transmitter and receiver and their is a connection between them but i have a problem no channel on the receiver is resetting to 0 for example if i connect a led to a potentiometer CH the led doesn't turn off if the potentiometer is all the way down but i can increase the brightness of the led when i move the potentiometer up even servos don't move or the motor on esc ,i can control the throttle but not turn it completely off. the same happen with switches can't turn of a led but can increase brightness of led when turned on. please if you have any idea tell me
thanks in advanced :)
Hello there. I have never heard of this kind of issue before. Are you sure you haven't changed anything in the code for the receiver channels to be stuck? Apart from this, I have no idea what to suggest...
yes 100% sure copied and pasted thanks for replying tho@@MaxImagination
hey man can i use it for a plane
i need to Attach 4 servos and a brushless motor to the recevier
Yes, you may use it for a plane with the given code.
@@MaxImagination Thanks a lot man you help me a lot
can i use attiny88 or 85 development board for this project thank you
As long as it's got enough memory to run the code (I wouldn't know its specs) then it should do fine.
P.S. Please excuse my late reply.
will you please make a breif video on how to connect it with elegoo car
Might do that one day, there still isn't a high enough demand. We'll see
Any chance you can make me a remote for my blink acton Qu4Tro using this. I know it’s a lot to ask, someone broke into my car and stole the remote and the board was at home. This board is sentimental, I have been trying for a year looking for a used remote but no luck, thank you in advance greatly appreciated!!!
how to add dual rate or end point trimmer because i'm planning to use it on rc car which steering end point is required.
I'm not exactly sure how that would be implemented in an Arduino radio set. Though, I do know that it isn't so hard to adjust the rate values in one of the Arduino's codes.
do your RC (anrduino rc) can plug ESC with BEC 5v-2A?
Yes.
Can you please tell me that how much range can we get with 7 channel tranmitter? And I also want to know that if the range of 7 channel will be less than range of 4 channel or no effect of channels on range?
The range of this TX and RX pair is about 1km. The number of channels does not affect range.
@@MaxImagination ok thanks
Hello, i am using a arduino nano for transmitter and pro mini for receiver should it work ? it's not working for me, the pro mini receiver gives full throttle from all channels(digital pins ) any ideas plz, is it a transmitter problem or receiver ? the pro mini is brand new
Hi there. This setup should work.
Please check that you are supplying enough power (3.3V) through a 10 microfarad filtering capacitor to both of the NRF24 transceivers and that your SPI communication wires are connected as on the diagram.
What other unusual/improper behavior is it giving?
thanks for replying, i have 10uf capacitor on both nrf modules and i tested them they all work but for some reason when i upload the receiver code on pro mini or Arduino Uno or Nano every channel pin gives full voltage as if i am giving it a full throttle signal from the transmitter for example when i connect a servo to the receiver it immediately start running, i think it's something in the code or maybe i am doing wrong wiring but i have already checked all the wiring more than 10 times @@MaxImagination
and exactly 3.3v supplied to the nrf modules @@MaxImagination
Can i use laptop hdd moter as brushless moter for rc plane?
A brushless HDD motor would require recoiling and rewiring to work as a regular RC vehicle brushless motor with ESC. Try finding conversion videos online of how to do this.
Hey dude, Can I use this for rc flying drone, What is the range of this transmitter
Hi, sure you may, but you'd need to go looking in a site such as GitHub.com for the code that will make this transmitter and receiver control a drone.
The range really varies on if what additional components you add to the radio module to smoothen its power input, the range is about 100m on mine, and these modules can transmit up to 1km.
So how can we control a dc motor by this this?. This thing has 3pins in output and a 5v motor has 2 pins can someone please explain to me?
Hi there. To control any motor whether be brushed or brushless, you will need a motor driver or 'ESC' to run it. Electronic speed controllers normally take 3 pins - Ground, 5V, and Signal.
@@MaxImagination thanks you Love from India 🇮🇳
@@MaxImaginationthanks bro I have the same problem 😀
hello max, can you hook up a brushless motor to the receiver?
Hello there. Yes, you may hook up an ESC with a brushless motor to this system.
@@MaxImagination oh ok thx
is it possible to use arduino uno with the same program?
Yes, as the Arduino UNO's specifications are almost the exact same as the nano, except only larger.
Can I use a JST connector to charge the battery and not the BSM? I’m on tight budget so I need to know. Bye!
No, a BMS charger is mandatory in this case, as it's a 2-cell battery, each cell needs to be balanced when charged.
Ok, thanks!
hey Max im building a Ardiuno rc plane for a STEM project at school and ive built the receiver and transmitter and put all the code onto the ardiunos and there not working, the motors will buzz non stop and every once and a while the servos will have a spazz but the transmitter isnt doing anything with the motors and servos, idk if you can help or not, thank you.
Hi, Eclipse. Please check that you've assigned the corresponding pin numbers that you've wired in your circuit. Also, it may be worth checking that your circuit is receiving enough power.
@@MaxImagination thanks for the help mate
@@mundycustoms You're welcome 🙂
HELLO MAX , Can i use arduino UNO for transmitter and nano for receiver ?? Reply PLZ
Hello there. Yes, you can use those boards for that kind of setup. Cheers.
@@MaxImagination Thank Ya!
Hello, do not be bored, I have a question, you are sending the link between the sender and recipient code, thank you
Download links for these two codes can be found in the description below the video. Cheers.
Wow Great work. but how can i solve signal interference problem ??
Hi, are you having a signal interference when using this around WiFi? What kind of signal interference are you troubled with? Thanks for your comment.
@@MaxImagination Thank You Sir. The signal is not stable
@@danielkibret8271 Did you make sure to add x2 10-microfarad capacitors at the receiver and transmitter ends as shown on the diagram? Also, try keeping the transceiver modules wired as close to the arduino boards as possible.
Play around with the antennas, sometimes they aren't properly connected internally.
Hello!
Thank you for the video, it was very informative, however i have a problem when uploading the file to my arduino, it is showing me the message "avrdude: ser_open(): can't set com-state for "\\.\COM3" " can you please help me out on this problem, would very much appreciate it if you could. Thank you in advance
Hi there. Thanks for your comment. Have you tried a different cables? Another Arduino? Sounds like your IDE isn't recognizing the Arduino due to a communication error.
Are you sure you are using the correct com port?
Sometimes arduino IDE can have trouble finding cheap/damaged arduinos
Hi, I want to recreate this for my school project, can I have a complete list of the materials including the wirings?
Hi there. As mentioned in my video, please check the video description below for the full list of parts with purchase links. Wiring diagrams are also linked below.
Hello Max , Can i use a Arduino UNO board for transmitter or as a receiver instead of Nano ,, Cause I have one nano and one uno
Yes, anything that can communicate over SPI will work. Might want to double check pinout but even that I believe is the same on both. Also, those "PS2" china gimbals are junk, nearly so bad as to be switches in some cases, Buy the cheapest "real" gimbals from banggood or aliexpress and your xmitter will be 100x better. One other note... the nrf24l01 pa lna that has metal shield over it is worth the extra couple $
Hello there. Yes, Arduino Micro, Nano, Uno, Mega... all of those boards will work with the project involving radio frequency modules that communicate over something called SPI. Cheers.
@@williamna5800 Thanks A Lot , Does the same code work for both? Just need to upload it while selecting Uno as a board thats it? If any other things are there please Let me know , Thank You once Again
@@Samuel_L.Jackson yes if the only thing you change is the uno/nano. The only thing you might need to tweak are the endpoints for servos/gimbals so you get full left/right and center is actaul center. Ideally 1000 = full left
1500 exact center
2000 full right
Edit: of course select uno for uno and nano for the nano.
@@williamna5800 Hey Any ideas how to Run this using Cordless motor , With gearbox [ From rc plane] Edit : I Hope 3.3 Volts will work for battery?? Thanks
can teach me how to connect the trasmitter with the reciever
They connect automatically when you power both sides on.
hi can i use wireless transceiver module for nrf24L01
Yes. It is a wireless transceiver module already.
Um can use that 'mini ESC' on the same code or a motor driver?
I do not understand what you're trying to say...
Most of the ESC's should work with this code
Hello i made my tx and rx but when I connect a servo the servo turns and stops but I can't control with tx I check wiring
What type of servo are you using? Have you checked the outputs with your multimeter on the receiving end? I think your TX and RX aren't connected, actually. Make sure you're using a 10uf capacitor across the power terminals of each NRF module to resolve connection issues - or use a more stable 3.3V supply for them.
Hello, can I use arduino uno instead of arduino Nano?
Yes, as the Arduino UNO has the same attributes as the Nano, just shaped differently.
Hello I am from Taiwan, thank you for your great video
hello sir I am an electronic engineering student I was wondering does this robot have rpm control
Hello there. It does not have RPM control, only PWM control.
Is it possible to use ESC to control RPM of a motor @@MaxImagination
Hello bro
Is it mandatory to select bootloader or can we select any of the other options?
When i select bootloader it's showing error while uploading
What should I do bro? Please help
Hi there. If you're using a knockoff Nano, please select Old bootloader.
Sorry to bother soo many times but, I still have question. Where I live, people don’t sell a 3 wire bms (or any other 3 wire) type chargers. I can’t find any online either, is there ANY way to charge it with a 2 wire charger???
Hi, no worries! I found the exact same type of BMS charger I use, here on Amazon:
www.amazon.com/Blomiky-Charger-Cable-Battery-XH-3P/dp/B072C3SS64/ref=sr_1_3?dchild=1&keywords=7.4V+toy+drone+charger&qid=1626781189&sr=8-3
Thanks so much! I just wanna say that I hope I not bugging you too much with all these questions, I’m just a dummie dum so I need a lot of help. Anyways, bye!
@@Mbb2220 Not a problem! Asking yourself to success shall be the way, buddy! Good luck with your project, see ya!
Can I use arduino Uno for transmitter and nano for receiver for making a drone ?
Yes, you can. This way you're also keeping the receiver compact, in a smaller package.
Thanks for replied.
thanks very much for the code
You're welcome! 🙂
Just a newbie question but, can I control 8 servos with just the two joysticks?
Hi there, hmm, I believe it can only control up to 4 servos, but with some additional coding, you may be able to figure out how to make every half-movement of a joystick to make each servo move for 8.
Thanks!
@@Mbb2220 You're welcome ☺
Hey man, can you please answer my other comment?
Hey boy, you did a great work. I made everything according to the film, but I want to connect to 1 ordinary motor, the normal dc motor has 2 wires and the receiver's pin has 3 pins how can I connect the normal dc motor to it.? I also applied coding correctly, but it doesn't work. Please help me connect a normal dc motor to it.
Hi and thank you.
The reason as to why your motor won't work with the setup you have is because the motor needs a brushed ESC (Electronic Speed Controller) with connects with the Signal, VCC, and GND pins on the receiver, leaving you with two wires at the output. You may order these ESCs online
@@MaxImagination Thanks. I didn't understand what you meant. Isn't there a way to use esc without use? Because they're really expensive. thanks
Hi, check out this diagram which shows how you can use a MOSFET to drive a simple motor instead of a proper ESC.
drive.google.com/file/d/1Tgkvqt1vDZrEoT5IZt2GP7_QmkYdilR6/view?usp=sharing
@@MaxImagination Thank you 😍 inside the chart.... Where should I connect the regulator? Because he didn't explain it. Thank you
@@leading6694 Following the circuit on the bottom right, connect the first pin of the Transistor to any Digital pin (signal pin) the third pin of the transistor to Ground (-) and the motor driving pin to your voltage source.
Hey, how do I connect a male bms connector to a charger? I have made the battery but dunno how to make the charger.
Hi again, a battery connector going to a bms must consist of 3 wires, as seen in the video.
One is Ground, the middle wire is the connecting point of the two batteries, and the other is VCC or the positive battery terminal, hope that helps.
@@MaxImagination thanks but again that didn’t answer my question. If I have a charger with positive and negative do I connect the ground with negative as well?
Hi, not exactly, looks like the charger you're using only has 2 wires, am I right? If so, you have to use a BMS-type 7.4V battery charger with 3 wires, not 2
@@MaxImagination ok, thanks!
if we need any binding between transmitter and receiver
No binding necessary :)
@@MaxImagination thanks
Hey bro can we control brushless motor using same code
Yup! You can.
@@MaxImagination thanks bro
I tried to make this transmitter and receiver and my wirings are correct, code is uploaded properly and it is getting enough power but the servo attached to receiver is not working. Can you help me ?
Sometimes servos tend to stop working due to a break inside where the wires connect to the board, could you check that? If not that, then I suggest you hook up a multimeter and measure if you're even getting a signal from the Arduino's pins. It may also be your transmitter's NRF24l01 that's not transmitting. It may help to add a 10 microfarad capacitor to its 3.3V power terminals.
@@MaxImagination I've done everything but still it is not working and I thought that my nrf module was faulty but it isn't
@@shayaanansari3419 Could you try with a different device other than the servo such as an LED to check?
@@MaxImagination k I will try
Hi Max, I shall be grateful to have the circuit diagram of this and the code too. Thanks in advance.
Hi there. The code and diagrams are linked in the description for you to download (as mentioned in video).
Hey max I didn't understand the connection between l289 with receiver
Hey! Maybe this can help: ozeki.hu/p_2999-how-to-setup-a-dc-motor-on-arduino-nano.html
@@MaxImagination thanks it helped me a lot
can we connect brushless motor to reciever?
You can, but you'll need to connect it through a brushless ESC.
Cheers,
Max
@@MaxImagination i do have a 30a esc ,thanks bro
Why are you using D9,D10 pins instead ofD7,D8. Some tutorials they use D7 and D8 pins ?
It does not matter which of those pins you use for the CE and CSN connections. Both work.
@@MaxImagination thanks.
Bro can we use servo in the place of esc
Yes, you can.
@@MaxImagination thanks bro
I am again afraid to try this if the code has some issues like your esp32 cam video
The code does not have issues, it may be due to the recent updates and your lack of understanding. I would kindly advise you to stay up to date with the ESP32-CAM code in the code author's page. Cheers.
Hey ! Can you control a drone with it
Hey! Yes, it's possible.
Hello sir.
What is the range of the remote???
100-1000 meters. The exact range you get will depend on how well filtered the power is to your radio modules and the environment you're testing them in.
Thank you sir..
From where we can get components...
Please check the description below for the components list with purchase links to Amazon.
i am facing problem while communicating arduino nano and nrf24l01 module ..help me
Hi there. What is the issue specifically? Have you tried seeing if the transmitter gives off outputs via the serial monitor?
Please make sure you're powering the NRF24L01 modules with 3.3V respectively on each end with a 10 microfarad capacitor on the power pins.
Also check that the pins you've assigned in each of the codes corresponds with what you have connected.
@@MaxImagination thank you its working...