HPMX / WEBER IDF screw adjustments

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 47

  • @V8N8T
    @V8N8T ปีที่แล้ว +5

    Great video EZGZ! Whenever I setup my idf's i always adjust the air bypass screws after they ar synced to allow even flow thru all the barrels for a super smooth runner:)

  • @krazveedub6781
    @krazveedub6781 ปีที่แล้ว +3

    I feel this video was made for me. I am currently working on my 40 idf and this video is very informative

  • @Darkstorm666
    @Darkstorm666 2 หลายเดือนก่อน +2

    Should I adjust the air bypass screws instead of seating them if the engine is running rich?

  • @chrisstephenson6718
    @chrisstephenson6718 หลายเดือนก่อน

    Thanks EZGZ, just what I needed.

  • @VWJawbreaker
    @VWJawbreaker ปีที่แล้ว +1

    Another great video with clear instructions and explanations!

  • @J8zzy
    @J8zzy ปีที่แล้ว

    Great to hear EZGZ instructions and videos. Have a nice summer 2023. Keep On Rolling❤ EZGZ The Carb Wizard RULEZ.

    • @TheEZGZ
      @TheEZGZ  ปีที่แล้ว +1

      Thanks, you too!

  • @plg402
    @plg402 ปีที่แล้ว +1

    what a great video! You sir just saved me a lot of money!

  • @dirtyscant3447
    @dirtyscant3447 ปีที่แล้ว +1

    EZGZ!!!!Thanks for sharing your wizard skills!!

  • @kevinhamling1963
    @kevinhamling1963 ปีที่แล้ว

    G'day Mr EZGZ,
    An awesome video. Hope you doing well ✌️Peace from Melbourne Australia.

    • @TheEZGZ
      @TheEZGZ  ปีที่แล้ว +1

      Always good to have you along mate 🙏

  • @philipcarmichael9112
    @philipcarmichael9112 6 หลายเดือนก่อน +1

    Hi I’ve got a 1760 40 idf. 110 cam do you know what jets I should start with

  • @RustyGlovebox
    @RustyGlovebox ปีที่แล้ว

    Great info GZ, you have a really helpful vid here Buddy

    • @TheEZGZ
      @TheEZGZ  ปีที่แล้ว

      I’m trying to learn how to post vids from my phone hehehe

  • @OwhyeeVdub
    @OwhyeeVdub ปีที่แล้ว

    Great breakdown.

  • @spidula
    @spidula ปีที่แล้ว

    Super usefull explanation on this ez...good stuff and good to see all your vids, I'm gona catch up on a few others

    • @TheEZGZ
      @TheEZGZ  ปีที่แล้ว +1

      Awesome, thank you!

  • @johnj2496
    @johnj2496 ปีที่แล้ว

    thanks great video
    🤔 i got my idfs on off a guy on ebay in maybe 2002 but they are from spain
    and my idle jets are NOT thru the side but down thru the top
    and ive only got the 2 idle adjustment screws by the base

    • @TheEZGZ
      @TheEZGZ  10 หลายเดือนก่อน

      Interesting. I thought all IDF and the copy's were the same...

  • @Antarath
    @Antarath 5 หลายเดือนก่อน

    My VW came with a single EMPI HPMX equipped with a 009 distributor. Always wondered why the vacuum ports on these things are never used. Guess I have a carb for sale then.

  • @bykr2009
    @bykr2009 ปีที่แล้ว

    Good information, do you know what size that accelerator pump adjustment nut is ?

  • @DrBaconCommunity
    @DrBaconCommunity 8 หลายเดือนก่อน

    thanks for your help! great video!

    • @TheEZGZ
      @TheEZGZ  8 หลายเดือนก่อน +1

      You're welcome!

  • @clintonwilloughby7606
    @clintonwilloughby7606 ปีที่แล้ว

    Just did my adjustments last weekend on my duals. #4 had a progression port clogged. Had to take the carb off and spray it out. Wish these plugs were tapped for cleaning them. Is there an easier way to clean the progression ports? As always, good video! Hope to see you at the Bug In next weekend!

  • @goldentrunnell7450
    @goldentrunnell7450 9 หลายเดือนก่อน

    Can you swap the older air/fuel screws for the newer style or does the old seat need the older screws?
    I'm rebuilding a set of 44 IDF Italian and was curious if the newer style screws would be better for adjusting?
    Thanks

    • @TheEZGZ
      @TheEZGZ  9 หลายเดือนก่อน +1

      If the seats are good the screws are interchangeable. For easier fine tuning use the longer screw but you may be more than 1 1/4 turns out on the idle.

    • @goldentrunnell7450
      @goldentrunnell7450 9 หลายเดือนก่อน

      @@TheEZGZ thanks!

  • @christopherwaller5600
    @christopherwaller5600 ปีที่แล้ว

    Hey EZGZ thanks for the great video. I’m trying to get my bug to pass emissions, and my results say I’m idling rich. Do I turn that hex screw at the bottom in or out ? Thanks again

    • @TheEZGZ
      @TheEZGZ  ปีที่แล้ว +1

      Idle fuel needle in very slowly and listen for idle ruff idle or popping noise then back out until it smoothes out. Take your time. Ignition timing can also effect emissions test. Also use best high octane available in your area

  • @kade997
    @kade997 ปีที่แล้ว

    Hey ez I want to get a thought on my 44 hpmx. It stalled at every turn and when I got back home and let it cool down it would no longer idle even though I hadn’t adjusted it.

    • @kade997
      @kade997 ปีที่แล้ว

      It had idled before while sitting still

    • @TheEZGZ
      @TheEZGZ  ปีที่แล้ว

      Sounds like to much fuel pressure and the floats aren’t holding the fuel back

    • @kade997
      @kade997 ปีที่แล้ว

      @@TheEZGZ thanks I’ll mess with it tomorrow

  • @demetricshorter6953
    @demetricshorter6953 11 หลายเดือนก่อน

    Mr EZ, I believe I need to tweak my accelerator spring, it’s idling fine, running good. But during transitions it stalls , sometimes completely cuts off, even while cornering. I was afraid to adjust the pump because I was getting a small leak from the pump spring leaking down into the cylinders (dual 40idf webers) any recommendations are much appreciated sir????

    • @TheEZGZ
      @TheEZGZ  11 หลายเดือนก่อน

      sounds like you need a new accelerator pump diaphragm .

    • @demetricshorter6953
      @demetricshorter6953 10 หลายเดือนก่อน

      @@TheEZGZ thanks. Here’s one other thing. Once I turned the car off, the carbs were making a noise( like compression) and gas was sitting in the bowel. I took a wrench and turned the engine and noise faded away… could this be timing too?

  • @vintage76vipergreenBeetle
    @vintage76vipergreenBeetle ปีที่แล้ว

    Great info.👍

  • @chadburkle1461
    @chadburkle1461 ปีที่แล้ว

    Do you live in Arizona or Colorado? I will be going that way this week. Don't know how you feel about a fan coming to visit.

    • @TheEZGZ
      @TheEZGZ  ปีที่แล้ว +1

      I’m in Loveland Colorado if you want to stop by

    • @chadburkle1461
      @chadburkle1461 ปีที่แล้ว

      @@TheEZGZ I might be able to stop by I'm about 200 miles from Denver Colorado

  • @johnklink4825
    @johnklink4825 ปีที่แล้ว

    I run dual Webers. Car backfires. Ant thoughts?

    • @micksmith9768
      @micksmith9768 5 หลายเดือนก่อน

      did you solve it? usually its a leaking exhaust , but i think a crack between the plug and valve can also do this

  • @CptnCrncyRzr
    @CptnCrncyRzr 9 หลายเดือนก่อน

    Thank you

    • @TheEZGZ
      @TheEZGZ  9 หลายเดือนก่อน

      You're welcome. Create a great ride.

  • @JohnnyRebel1776
    @JohnnyRebel1776 ปีที่แล้ว

    EZ! 👍🏻