Bagger Brothers 2 into 1 Maverick V3 Full Install With Sound Clips
ฝัง
- เผยแพร่เมื่อ 11 ก.ค. 2024
- Bagger Brothers Exhaust bit.ly/34feozK
Tools I recommend for this install.
Ring Expander Pliers - amzn.to/3HTgymu
Anti-seize lube - amzn.to/3HOsy8R
Pick Screwdriver/gasket removal tool - amzn.to/3n85qdG
Blue Loctite - amzn.to/3GkfbNG
In this video, I will show you how to install a side dump 2 into 1 header exhaust system from Bagger Brothers on your @harleydavidson touring motorcycle. This Maverik Souza V3 with Kory Souza Tip is SIK! We love it. Easy install with minimal tools and just a little bit of know-how you can have this installed pretty quick! We have included a sound test with a cold start, idle, revs, and also take-offs and drive-bys!
Get yours today!!
Chapters
0:00 Intro
4:28 Unboxing
5:30 Remove Old Exhaust
10:47 Swap Out o2 Sensors
13:51 Change Header Gaskets
15:02 Install New Exhaust
24:01 Sound Clip Cold Start/Idle
25:03 Sound Clip Drive By
25:59 Walk Around Look!
26:53 Outro Thank you!
As an Amazon Associate, I earn a very small commission from qualifying purchases. Thank you for your support and for helping our channel grow!
🔵My Gear - Sony Handycam - amzn.to/3mhAIyv
GO Pro Hero 7 black x 2 - amzn.to/3p9fxQK
Go Pro Helmet Mic - amzn.to/3e6vRM8
Packtalk Bold Duo Helmet Coms - amzn.to/3e4z5jd
Bell SRT Helmets - amzn.to/3GWdpBZ
Samson Go Mic - amzn.to/3Fale6Q
Video Lights - amzn.to/3shXUAk
Tripod - amzn.to/3paIWu1
Mini Tripod - amzn.to/3snWtjR
Go Pro Gimbal - amzn.to/3yHw69H
Go Pro Mic - amzn.to/33MzPYp
Go Pro Mic Adapter - amzn.to/3p69c8N
Go Pro - Filters - amzn.to/33HS7dc
GoPro - Case - amzn.to/3p8CKCB
#sikbaggers #baggerbrothers
🔴GET SOCIALISTIC
🔗Facebook Group SIK Baggers - bit.ly/38GRKgI
🔗Instagram - bit.ly/2HwBZge
🔗My LINKTREE - linktr.ee/sikbaggers
🎵All Music Licensed Through www.epidemicsound.com
🚩The video content is available for informational and educational purposes only. Steven Housden, SIK Baggers does not make any representation or warranties with respect to the accuracy, applicability, fitness, or completeness of the video content. Steven Housden, SIK Baggers does not warrant the performance, effectiveness, or applicability of any sites listed or linked to in any video content. The information contained in the multimedia content (“Video Content”) posted represents the views and opinions of the original creators of such Video Content and does not necessarily represent the views or opinions of the Company. The mere appearance of Video Content on the Site does not constitute an endorsement by the Company or its affiliates of such Video Content.
Steven Housden/ SIK Baggers assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Any injury, damage, or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user. - ยานยนต์และพาหนะ
Thanks for the video on the great looking/sounding system.
Thanks for checking it out DED! Much appreciated!
Great video!! That exhaust looks and sounds great!!
Thanks man...im digging it...its loud but man it looks good
Thanks for the install vid
Most welcome!
That's a beautiful sound!!
Yeah love that pipe! Shes loud for sure.
Great videos, thank you for posting them! Been doing some personalizing on my ‘20 tu tone green flhtk. Got the chrome bug! Lol.
Right on! Glad the videos are helping! Bet the chrome looks sick on that green!
💯 brother 🤘🏾....sounds and looks awesome 🤙🏾
I wish my camera did better on that sound...so much better in person!
Great video keep up the good work.
Thank you Robert!
Great video, Steve. I will install the same on my 22 Road Glide ST. Thanks for posting. Love your videos, very helpful.
Thank you Nado!!
How did your install go, how do you like the exhaust? ✌️
Another great video, 🤟
Thank you!
Looks good, sounds good. 👍
Thanks David...pretty loud but im digging it. Still has a nice left off crack and low end while cruising...its juts the take off...whew! Loud!
See ya soon Steve in Daytona. Thanks again for another video
One more day and were hitting the road! See you soon!
Sounds great I like those pipes
Yes..love this pipe however they are always back ordered for some reason.
🤩really beautiful 🤩 👍
Thank you Marco!!
Cool video. Been looking at 2-1 systems for my 06 RG. Will def checkout the link for this one…. I put a little antisieze in the slip joint of the muffler & head pipe also. Makes install easier & removing them later as well.
sorry for the delay, catching up from our Sturgis trip...excellent tip too! thank you for checking it out....hope you find what you are looking for!
Steve looks nice glad you are back working on the Street Glide being I am a Street Glide person 2006
We have some more chrome pieces coming for this bike...not much else I can do to it really lol but still a few things.
Nice!
Thank you Jim!
Beautiful!!
Did u have to tune it after install of exhaust ?
SIK 👍
Thanks Michael!
Oh my goodness.....I think I just found my new exhaust. 2020 street glide special here. thank you got taking the time to make this vid my friend!! I have Tab Bam Sticks with Zombie baffles right now. Can I ask, how is the lean with your exhaust. I like to take my corners kind of low sometimes.
this exhaust sits up pretty high...never scraped it or even came close...its pretty sick!
Nice bagger! What floorboard set is that? OMG! Those are sick!
Thank you! Unfortunately I had those custom made for this bike and they were one offs...I've since sold them and moved on to something else but yeah they were sick...The cost was sick too lol I'm actually running the advanblack boards, shifter arms, shifter pegs and brake now www.advanblack.com/parts/harley-parts/harley-parts-trims/advanblack-vengeance-floorboards-brake-heel-toe-shifter.html
I got there batwing fairing.
Any idea on when these will become available again?
Do like what you installed, good job ..to loud for me...keep up the good work. 👍
Thanks Alvin..yes very loud...takes some getting used to for sure..thanks for checking it out though! Be safe.
How does the sound compare to the TAB you have on the road glide? I like the TAB sound but also like the side dump
Wow that is a booootiful bike !!! Sound is AWESOME !! THX for sharing !!! Cold day here so good day to watch you work ! Is that center stand electric ? How do you like it vs side stand ??? I have been tempted to get one ......
Thanks paul...love the centerstand and yes its electric...from southern Oregon baggers...you'll need air ride to use it of course.
@@sikbaggers Air ride ... I did know that ...THX
they sound so much better in person
agreed!! So hard to get get good audio on exhaust.
@@sikbaggers i have the vance and hines fp3 fuelpak but not sure which map will work well with the bagger brothers exhaust
I have python Rayzer on my glide and I called FP3 folks and they walked me through the whole set up. Great people.
@@sikbaggers one of my heat shield brackets has broke off into a few pieces. how would you recommend to repair it so I can get rid of the rattling
Well done, again, brother. $1,100 worth of exhaust that doesn’t come with gaskets and have to finagle that insert into side mounting bracket (why they don’t tac that in place for you is beyond me)??, no thx. Ill stick with my D&D, but to each their own. Pro tip, throw exhaust gasket in the freezer before installing. They shrink a bit, making you grunt less! She sounds great! Thanks again for taking the time to do these for us.
Is usually freeze the gaskets on smaller engines..the 103s and bigger I generally don't have am issue with getting them in...but yes..great way to save some time and jacking up your new gaskets
Man i am going to try this pipe on my bike. I have D&D NOW AND WENT WITH NO CUT OUT BAGS AND FENDER AND WAS GOING TO CUT THE PIPE AND TO A TURN DOWN AND FOUND OUT IT WILL NOT WORK. SO I WILL TRY THIS PIPE
Does this exhaust comes with a baffle or not cuz somebody please answer me thanks.
Man I love those floor board mounts! I noticed you said those are a one off build, any hopes a rider could purchase those? 2010 street glide.
Hey harm..the guy that made these is no longer making anything right now that I know of...actually told me after doing these in chrome and all those spikey bits really tore up his polishers and said he would never make another set like that lol
@@sikbaggers OK thanks for replying back.
Bought the Bagger Brothers exhaust. They rusted in about a year and not made very well if you ride a lot. So I put a cam in my motor and bought new exhaust since this one was not very good. Ike is much better now with stainless steel blackjack exhaust’s. I have pics of the Bagger brothers after about a year. Rusted head pipes. They are on display on the wall of shame at Harley Davidson.
good to know...had mine for right on a year and not an ounce of rust on them. But of course my riding/storage conditions could be very different from yours. Ill keep an eye on it...thanks for the heads up
@@sikbaggers I ride in the rain. I store mine in the garage. It’s heated and air conditioned. I think the rain cause the steel to rust.
Steve I noticed you have passenger floor board and highway pegs. Where did you get them and is the bracket used, different?
the floorboards on this bike were made for it..one offs made for this build...but the adjustable pegs and brackets came from Ciro3d. here is the links youll need to put them on. Adjustable Passenger Comfort Peg Mounts - shrsl.com/1r12t
Ciro Rail Footpegs - shrsl.com/1r12x
Footrest Adapters for H-D Male Mount - shrsl.com/1r131
i remember you putting Performance did you not like them Steve?? i just put them on my street glide but i still need head pipes
I put the Tabs on the road glide...Ive had those custom turn downs for a couple of years and just really like the looks of this pipe...still love the tab performance pipes though..they sound amazing!
Duel turn down ...like those...special cut
yeah they were cool ...pretty loud too...likes to throw a lot of dust up though.
Yea I bet,got to old for that,stick to what I got..duel cut factory..glad to see ya back ☕✌️
I can’t decide between a freedom performance combat shorty or their turnout pipe, it looks like the same 2 into 1 setup just with different end caps. I love the deep tone and I want it loud too, everyone says the side exits are louder but I think that’s just the rider’s perspective, I think they would sound the same to anyone not on the bike but I have no experience with side exits so idk. Any thoughts?
It has a deep tone but I assure you no matter where you are sitting, on the bike beside the bike , behind the bike...a block away..lol they are loud!
Can you still hear your music while riding?
Do you have an issue taking a sharp right turn? Looks like it may drag the ground before the floor board would.
no...its so far out that you would fall over before you scrape that pipe
Is there any type of baffle in this exhaust or is the loudness head rattling.
if there is any in the pipe its minimal...they are loud...but every single side dump ive seen is loud. I think its more the placement of the pipe when were used to it coming out the back
Did the spacers come with the pipes? For the right foot board?
yes it comes with it
Is your bike a Milwaukee 8 motor and is there any build work done to the motor? Want to know the sound difference if it is not stock versus a stock motor.
its a 103 and no engine work has been done..the m8 sounds pretty much exactly the same
@@sikbaggers that pipe sound is amazing. Ordering one this week to go with my dominator fender and extended bags with no cutouts. And of course it is from AdvanBlack. Thanks for the response and keep up the great videos. You help a lot of people out with those videos!!!
Did you have to retune the bike after you installed the 2 into 1 exhaust?
Yes going from a dual to a single exhaust you should always re tune
Hello . I have a 1982 super glide and I'm looking for a built drag pipe exhaust with pie cuts . Do you know of anyone that builds exhausts .
no im sorry I do not
@@sikbaggers ok thank you
New bag lowers too?
I already had the no cut out bags for the custom turn downs but if you go from dual or single out the back to the side dump you will need to get no cut out bags and extension or fender.
@@sikbaggers it's a good look for sure.
How can I contact y’all for some questions
slhousden@gmail.com
What kind of rims are those
SMT Machining Twisted Steel - www.smtmachining.com/shop/twisted-steel-front-wheel/
🚬😎✅✅✅✅✅
Thanks for checking it out Antonio!
I need that . T.C. 95 ?
tc 95?
He prolly meant TC96 LOL
@@MrHarm63 lol, probably not. The S&S kit I have turned my ‘02 TC88 into a 95. He might have actually meant what he said.
Called the company, I think they’re out again. Didn’t even have a timeline or take a pre-order….disappointing…This is the 2-1 that I want. 🤷🏻♂️
yeah and if you get a timeline it will change more than likely...it took awhile to get mine
Great video keep up the good work.
Thank you!!