How To Diagnose A P2015 Code On VW Passat, Tiguan, CC, Jetta TSI/ CCTA 2.0 Turbo 2009 & Up
ฝัง
- เผยแพร่เมื่อ 6 ต.ค. 2022
- If you’re getting P2015 code (intake manifold runner position sensor switch circuit range performance) and have misfiring codes, it is probably a broken manifold.
❗️If you find this video helpful, I would appreciate a $uper Thanks that can be found below the video. Thank you!
What Does VW / Audi P130A Code Mean
• What Does VW / Audi P1...
What Causes VW P0087 Code - Fuel Rail/ System Pressure - Too Low
• P0087 Code On VW Tigua...
How To Diagnose A P0341 Code On VW
• Diagnose A P0341 Code ...
How To Diagnose & Fix a P2440 Code on VW
• How To Diagnose & Fix ...
💰Save money on other VW / Audi repairs
❗️2.0 TSI Engine Serious Common Problems to Watch Out For on VW and Audi
• 2.0 TSI Engine Serious...
VW/ Audi 2.0 turbo 2008-2013 Timing Chain Tensioner Failure
• VW/ Audi TSI 2.0 turbo...
How to Replace Upgraded Timing Chain Tensioner on 2.0 TSI VW/Audi 2008-2014 engines
• How to Replace Upgrade...
Cranks But No Start? - VW Passat, Tiguan, GTI 2.0 turbo 2008-2013 - Check This First
• Cranks But No Start? -...
How To Diagnose & Fix a P2440 Code on VW / Audi 2.0 Turbo TSI 2008 & Up
• How To Diagnose & Fix ...
Timing Mark Alignment for Valve Train On 2.0 Turbo VW And Audi 2008-2015
• Timing Mark Alignment ...
Rear Main Seal Leak? Check This Easy Thing First - 2.0 turbo VW Passat, Tiguan, GTI 2008- 2014
• Rear Main Seal Leak? C...
Serpentine Belt Removal and install on VW Volkswagen 2.0 turbo engines 2008-215 - Simple & Fast
• Serpentine Belt Remova...
Complete Cylinder Head Removal & Install On Popular VW, Audi 2.0 T TSI Engine Gen 1,2,3 2008 & Up
• Complete Cylinder Head...
💰Save money on your car/truck maintenance and repairs:
Don’t Get Stranded With a Dead Battery in Winter - Do 3 Top Battery Checks Now!
• Don’t Get Stranded Wit...
Top 3 Reasons Why Your Car Won’t Start
• Top 3 Reasons Why Your...
Don't let Timing Belt Failure Happen
• Don't let Timing Belt ...
Top 6 Gas Saving Tips
• Top 6 Gas Saving Tips ...
Look what happens when you neglect your engine oil
• Check and Change Your ...
Gas Pedal Sticks? Car Jerks? - Easy DIY To Make It Smooth & Safe
• Gas Pedal Sticks? Car ...
What Does An Exhaust Leak Sound Like? - And How To Find It
• What Does An Exhaust L...
Check your Engine, Coolant, Transmission, Power Steering Fluid, and Brake Fluids
• Check Your Car Fluid L...
Blown Head Gasket - Don’t Neglect Your Cooling System- Look What Happens
• Blown Head Gasket - Do...
What Does Engine/ Serpentine Noise Sound Like And What Does It Mean? - Squeaking & Squealing Noise
• Serpentine Belt Squeak...
Always make sure your lug nuts are TORQUED and not done with an impact gun
• Don't Use This When Ch...
How to diagnose and replace wheel bearing going bad on any car
• Whining, Grinding Nois...
Learn why the tire pressure is important and how to check it in your car
/ bm8wnjripj
Remove and replace Broken or Stripped Wheel Stud on most cars
• Broken or Stripped Whe...
Cheap Way To Check For Bent Valves Without Removing Cylinder Head
• Cheap Way To Check For...
Fast and Easy Way to Restore Faded Car Paint and Scratches - With Minimal Tools
• Fast and Easy Way to R...
The Best Way To Fix & Repair Broken Wire in Your Car - Soldering Car Wires Together
• The Best Way To Fix & ...
Car Air Conditioning AC Not Working? - Diagnose And Maintain It At Home
• Car Air Conditioning A...
Replace Windshield Wiper Blades in 1 Minute
• How To Replace Windshi...
⁉️QUESTIONS
If you have any questions or I missed something, comment below and I’ll answer and try to help you out
If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the future.
⚠️Disclaimer:
The videos on Motorcarnut channel are posted with informational purpose only.
Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video. - ยานยนต์และพาหนะ
You are absolutely correct thank you ❤️
You are so welcome! Thank you for the comment!
Awesome. super helpful. great explanation and important details that nobody else mentioned. Do you have a video of replacing the intake manifold? Thanks,
Yes, search my channel for water pump replacement, I take off manifold in that video
I was getting this code after replacing the whole manifold. I honestly didn’t think that plastic house would keep it it from running right and I didn’t have the rubber to connect it. I will plug it in when I get home and if it works you have finished my 3 week repair process🤣🙏🏽👍🏽
Awesome! Hopefully all goes well!
Did it worked?
I also had this code. Changed the sensor. Didn’t work. Took the intake manifold apart. All parts work. Nothing loose or broken. Was about to give up. Before putting her intake back on there engine , decided to clean the flaps and the manifold itself since it had a lot of gunk on the flaps. Put it back and it has been 2 days and no code yet. So, maybe for some of you guys try cleaning the flaps and the intake itself.
Great tip!
I see you've had my troubles.. off and on multiple times.. well I just bit the bullet and replaced the entire manifold thinking that was the best bet sensors and all and bam before I started it I tried clearing the code... NOPE damm that was a lot of tedious work... and it will not clear... I didn't have some carbon on my valves was your effort worth it? Code cleared drove normally no more code?
I'm about to tear it down again should be easier this time but yea good cleaning check the wire to the sensors and reassemble I guess..
I "DO"" HAVE CARBON BUILD UP !!
Great video. I have a 2009 VW Passat CC 2.0TDI (diesel CBBB engine - aluminium intake manifold). I had this code several years ago - I purchased the DieselGeek bracket that prevents over-travel of the intake manifold flap actuator. The fault has come up again several years later - wonder what it could be this time? vehicle runs fine, but scan shows the intake manifold runner control Bank 1 stuck closed and also the fault for stuck open? Wonder what it could be - is that vacuum connection the same for the TSI and TDI?
Yours is a little different, can be the sensor on the runner or the vacuum solenoid or the flap itself that is binding.
Superhelpful video. I have a 2014 scirocco 2.0 tsi and got a 2015 code. Took it to a big indy shop who want to replace the camshaft sensor. From my search the intake manifold replacement should fix the issue. Can the camshaft sensor throw a 2015 code?
Yes but rare. More often it's the timing chain tensioner that jumped the chain.
Good job
Thank you!
just had a new manifold put on in January of this year....got that P 2015 code.....
Was it an aftermarket one?
It was the newer one....pn 06J 133 201 BH
@hmorales3377 make sure sensor works and electrical connection is fine. Also no vacuum leaks anywhere because that can set that code too.
Replaced manifold had all new stuff in it ..did a little cleaning on the inserts only did not clean valves and reassembled it correctly and clean as possible tried to clear code before starting and bam p2015........ that was a lot of time and cash ... now i wish i cleand up the valves..
The intake runners didnt look real bad that came out and i figured i solved the issue with the new intake but no dice.. any suggestions?
If you have a directional scan tool try to activate the runner flap. Also can be wiring problem if you already changed the flap sensor.
Can you tell me where the other vaccum line on the intake selinoid goes I recently put injectors in my Volkswagen CC and I can't figure out where the other vacuum line goes to that seal annoyed on that nipple
One goes to from the back of the vacuum pump to the solenoid, then to the vacuum actuator,if you do have another port it’s just a vent with a filter that mounts in the middle of the valve cover
Quoted 1k to get a new manifold and runner put onto my Skoda Superb, the hell with that. Can get the swirl flaps deleted and remapped for 250
There you go!
I've been dealing with a strange vacuum suction noise coming from my car when I start it. The check engine light will flash and then It'll stop as well as the gurgling. I don't know whats happening. I have the flapper fix kit from ECS Tuning installed, but I'm still getting misfires, but also my spark plugs fouled in a day.
I have 2017 VW CC.
Did you check the PCV valve? There is a round piece on the top and on the side is a hole, when the car running there should not be vacuum coming from that whole, if there is it PCV valve should be replaced. The gurgling can be a blown head gasket which would also cause misfiring.
I replaced my intake manifold, and sensor and still getting the stuck open code on my 1.8 TSI. We just fixed a fuel leak that occured during install, still with the code. Please help?!
Could possibly be the wiring to the sensor?
Is there a third vacuum line on the solenoid or is the bottom barb capped?
Some models have a third vacuum line that goes to a fresh air filter on the valve cover and should not be capped!
@@Motorcarnut well my daughter’s doesn’t have anything on the third barb. Should it be capped?
No, it should have the fresh air kit with is basically a rubber hose with a air filter attached. Or just run about 1 foot of hose and attach it somewhere near the oil fill cap area. If you block it, it will cause problems.
I’m getting the same code and the same multiple cylinder misfires on a 1.8 tsi, same thing?
Yes
Nwed help i replace new manifold but still appear code
Probably a bad manifold or sensor on it. Was it a new factory part?
Got this code on my 2012 vw cc, checked the circle. Didnt pop out. Checked for a leak as well and no leaks. I did notice a little bit of oil around the pcv valve, checked the vent for suction and no suction on that either. Any idea on anything else i should check?
Got to check the intake runner flap for proper operation or can be the sensor near the oil filter on the intake manifold.
@@Motorcarnut I'll check it out, thank you
No problem
Did it work for you?
Will this cause smoke out the exhaust pipe please respond im having this issue on a car i just bought
No it won’t.
Thanku for responding. It was a fuel injector causing smoke. I did replace manifold but im still getting p2014 and 2015 codw
I got this code on my 2012 CC.
Symptoms: gas needle going up and down, speedometer not working, EPC light on.
Any other codes coming up?
I have this same issue, no other codes came up for me.@@Motorcarnut
I had this code on my mk5 gti and replaced the whole manifold, sensor, and solenoid, but the code keeps coming up. Do I have to use vagcom to reset the solenoid or something on a tsi? Any tips?
If wiring is fine you may need a software update. You don’t need vagcom for that.
@@Motorcarnuthow do I do that?
Dealer I’m afraid
@@Motorcarnut ugh, well ill try that man thanks for the help.
Argh, I just cleaned mine and put it back on and it's thrown this code. These are a nightmare to take off and on. I have read they might be replaced by VW upto 140k miles as a recall, any ideas? Anyways thanks to your great video on timing chain replacement my cars almost completely sorted, thanks again dude. However I am beginning to think these engines are junk.
Thank you for the comment. I didn't know about that recall. They do have their problems but what vehicle doesn't?
@@Motorcarnut No, thank you dude, id be stuck without your help. I guess they all have issues but the list here seems endless, modern cars eh! cheers.
Really appreciate it!!
Would it be the same with a 1.8t Passat
Not really, no
I just had this light pop up (2010 vw cc), I’ve had a small coolant leak for about a year now (around mid engine) could that be related?
It also tends to overheat slightly for the first 5-10 minutes of operation and will drop down to normal operating temp afterwards
No, I thing the thermostat is staring to fail.
2012 Volkswagen CC Sport. Just replaced PCV, Coils and plugs and installed a new intake manifold. still throwing p2015 and occasionally 0300 codes. but mostly p2015. The engine revs higher while in park and the actuator on the intake Manifold seems to be stuck in the open position. Even when I manually move it back to ease the vehicle back to normal rpm it sucks the actuator arm right back. Its like there's too much vacuum. Any advice? just buy another intake manifold?
I don’t know, sounds like you have a vacuum leak somewhere. When you installed the manifold you made sure the injectors slipped into the slots correctly? Because if not that can create the problem you’re having.
So don't do the aluminium cap fix?
I wouldn’t, that wouldn’t stop a vacuum leak and aftermarket intake is more affordable
Would a blown turbo leaking oil into the intake charge cause this P2015 code? I’ve replaced the manifold with the updated design one, carbon cleaned, checked vacuum, etc etc. I’m thinking that oil is getting onto the runner flaps, migrating over to the sensor, shorting the sensor out, and tripping the code. After the manifold replacement it took a month or so for the code to come back. 2016 VW Tiguan 2.0T 109k miles. This car is a demon spawn from Satan himself I can’t believe how dogshit these engines are. They’re in everything VW and Audi! Terrible!
Yes, especially when these engines the way they are designed build up carbon like crazy and cause all kinds of problems. Also can be a computer software firmware update needed sometimes.
@@Motorcarnut Ok glad to know that’s not just a crackpot theory I’ve got. I’ll definitely be replacing the turbo then
@tylerroe5175 like I said make sure it’s not something else because the turbo is expensive and rare that it would cause that problem but it’s possible, good luck!
@@Motorcarnut I’ve pretty much exhausted every other option it could logically be and even though the manifold is newer now it had a shit ton of oil built up inside it when I took it off to look for more issues
@tylerroe5175 ok, then maybe it’s the turbo does the car but oil?
I changed my whole intake manifold but Still showing the engine light why
Did you reset the computer?
I broke that solenoid when replacing a water pump, I wasn't able to find any online that would of arrived in time. My solenoid that broke only had the two barbs for the hose and was capped off at the end, I was able to find a solenoid at a junkyard but it had another hose barb where mine was capped. I ended up just cutting it and placing the filter and little plastic cap from my original solenoid onto it. Could this cause code P2015? Really don't want to take the manifold off a third time lol
Not if it’s working properly.
@@Motorcarnut thanks for the reply! Any way to test the solenoid? I unplugged it and put direct power to it and was able to make the actuator arm(?) move, but when plugged in the arm doesn't move at all even when increasing rpms above 3k in P
@PityFvck has to be under load while driving that’s why