Audi SEAT Skoda VW 2.0 TDI Intake Inlet Manifold P2015 Error Flap Actuator Motor Bracket
ฝัง
- เผยแพร่เมื่อ 28 ส.ค. 2017
- Link to purchase product: x8r.co.uk/audi/inlet-intake-m...
The Problem
P2015 error caused by over rotation of the actuator motor on the intake manifold.
If your vehicle has a P2015 error it is very likely the main dealer will look to fix this issue with a complete new intake manifold which can cost £700+.
The fault however usually lies with the actuator motor on the intake manifold. There is a small plastic limiting stop on the butterfly assembly within the manifold which this motor operates. This is delicate and inevitably wears and causes the actuator motor (V157) to over rotate triggering the P2015 error or associated symptoms.
Our repair bracket can be installed very easily providing a solid limit for the actuator motor- curing this fault for the life of the vehicle. There is no need to replace the complete manifold / actuator motor which would only fail again.
Symptoms of the fault
P2015, Implausible Signal - MIL ON, VAG 8213, P2002, P2009, P2015, P2017. Engine management light lit or limp mode. Intermittent or constant CEL (check engine light) DTC 2968, 18447, 008213, Intake manifold flap position sensor fault.
Vehicles affected and compatibility
ALUMINIUM MANIFOLD:
VAG 2.0 TDI four-cylinder common rail engines 2008 - 2014 with aluminium manifold. Not suitable for V6 TDI or 2.0 Petrol Turbo engines.
Part number 03L129711E with V157 actuator motor only.
Fitment will vary by region. Please check manifold part number on the vehicle.
Volkswagen Amarok, Beetle, CC, Eos, Golf, Jetta, Passat, Scirocco, Tiguan, Touran and Transporter.
Audi A3, A4, A4 Allroad, A5, A6, Q3, Q5 and TT.
Seat Alhambra, Altea, Exeo, Ibiza, Leon and Toledo.
Skoda Octavia, Superb and Yeti.
Associated part numbers:
Engine codes: CAAB, CAGA, CAGB, CAGC, CAHA, CAHB, CBAA, CBAB, CBAC, CBBB, CBDA, CBDB, CBDC, CEGA, CJAA, CMEA.
PLASTIC MANIFOLD:
VAG 2.0 TDI four-cylinder common rail engines 2008 - 2014 with plastic manifold. Not suitable for V6 TDI or 2.0 Petrol Turbo engines.
Part number 03L129711AG with V157 actuator motor only.
Fitment will vary by region. Please check manifold part number on the vehicle.
Volkswagen Amarok, Beetle, CC, Eos, Golf, Jetta, Passat, Scirocco, Tiguan, Touran and Transporter.
Audi A3, A4, A4 Allroad, A5, A6, Q3, Q5 and TT.
Seat Alhambra, Altea, Exeo, Ibiza, Leon and Toledo.
Skoda Octavia, Superb and Yeti.
Associated part numbers:
Engine codes: CAAB, CAGA, CAGB, CAGC, CAHA, CAHB, CBAA, CBAB, CBAC, CBBB, CBDA, CBDB, CBDC, CEGA, CJAA, CMEA.
Our solution
Fit our unique design bracket and cure this over rotation with a hard stop curing this fault for the life of the vehicle.
Our bracket can be fitted very simply usually in under 15 minutes with basic tools. It simply attaches to the manifold actuator motor and stops the over rotation which causes the fault. Many of our customers have purchased as a preventative measure before the motor fails.
Our part limits the motor to the same range as when it was new. Avoid the cost of a complete new manifold and actuator motor this would only fail again and necessitates the removal of the fuel lines which can cause other issues.
No software (VCDS/ VAG COM) is needed for this repair, check out our instructions and videos, after the bracket is fitted the error will clear on its own.
Our bracket is unique in design, CNC machined from billet aluminium polished then anodised. Our bracket utilises stainless steel fasteners providing the best solution to this common fault.
We also include a replacement spring for the actuator motor as this can often be lost or damage when fitting the bracket. Fit our bracket quickly and simply and cure this common fault.
You will receive
1X CNC machined billet anodised aluminium bracket
1X Stainless steel actuator motor spring. - ยานยนต์และพาหนะ
great stuff, i bought one as its easily accessible for UK customers and it worked a treat on my audi a4 b8
Does it work on 1.8TFSI ?
@@aizazabeer9316 might do not sure
Hi. Where you bought one from?
This is all very well, the three bolts are in a space where I can’t get access to them. I probably need to remove the entire intake manifold which isn’t included in your video. Fitting it on a bench is the easy bit
Thank you Bro
For others with black pastic manifold having access problems to fit the bracket I have developed a solution that involves changing the hex bolt supplied with the repair bracket for a T30. Other steps may assist you if you can at least get a space above the three motor attachment bolts free so you can get a fine tooth ratchet in there. Shout out if you're one of these folk.
Yup that's me
Right Guys. I own a 2009 Passat 2.0 TDI with the plastic intake manifold. I have just successfully fitted the X8R Bracket "WITHOUT REMOVING THE INTAKE MANIFOLD!" Took about 5 hours, a few tool modifications, removal of the entire air intake box/housing and a "LOT OF CURSING!"
Did it resolve your issue?
@@nNIicCoLA Yes it sure did. No P2015 since I did it. Difficult to do without removing the intake manifold but worth it, a lot less hassel than stripping the whole thing down! Hope this helps ♥
It took 5 hours and you didn't remove the manifold? What the!
Hi, are you able to share how you did it without removal of manifold?
@@SamSam-bf6ir Completely removed Air Breather Box and Battery plus Battery Insulation and Cover. Discnnected/Moved any Pipes or Loom in the way. Then had to modify a Torks Bit to fit into a spanner and then with a lot of patience managed to do it. Ill save ya some trouble however with a link to a guy who does what I did and with a small wrench he bought from Germany which made the job a lot faster for him. Ill go look for it and post a link here so check back....
godd evening ..and thanks for the video i have a question my car is an audi a4 b8 8k.5 TDI 170 cv motor code caha with metal manifold wish is the one i need to buy thanks ..sorry for my english .
Good video, thx
Glad you liked it! - Georgina, X8R Ltd
Does it matter if i buy plastic or aluminium?
I discovered I'm not the only one with a P2017 code after installing a repair bracket and clearing P2015. I have a theory after noticing that the rotation of the actuator lever starts about 20 degrees late. I don't suppose you still have the black plastic manifold in the picture? Its possible there may be a simple solution. If you'd like to explore that with me in the interests of your customers let me know. I am here @BuyersReport if you would like to get in touch
Where l can buy one for CAG engine?
Hi there. I just fixed the bracket on the v157 motor, erased the p2015 error code, but after 20 min is still on. The CEL keeps coming back on. Put brand bew intake manifold and v157 motor with the bracket, but the CEL still coming on after 20 minutes.
Hi there, did you solve this in end and how? I did the same as you, bracket -> after 2 days it came back. Now I'm afraid to but brand new intake manifold. Let me know
@@crivion I have this same issue. Did you get yours fixed?
@@barryrob1978 No - the only remainder is checking the cable between the ECU and Motor.
and I also install brand new manifold and motor - don't do it
I have an Audi a4 b8 and It’s easier to remove the manifold.
Does anyone have any guidance as my fuel economy has gone rubbish after installing this? EML gone off though
Hi, we have not heard of this issue before and is likely to be unrelated. - Georgina, X8R Ltd
What about Skoda Superb petrol 1.8 / 2009 / code CDAA? I have the same "error 2015"
Hi, please email us or call with your reg or VIN and we can check for you.
@@X8RLtdUK ho bisogno del pezzo del alumino dove posso comprare
Do you have a USA website?
Dieslgeeks.com
Were can i order for the plastic manifold
You can order here: x8r.co.uk/audi-seat-skoda-vw-2-0-tdi-intake-manifold-p2015-error-motor-repair-bracket-fix
Buy from the originator - DieselGeeks.com.
Merhabalar bunu yapıpta arıza kodundan kurtulan var mı?
how Can I buy I don't see any link
x8r.co.uk/catalogsearch/result/?q=p2015
dove trovo questo ricambio ? grazie
Ecco il link: x8r.co.uk/audi/inlet-intake-manifold-repair.html
gdje kupiti taj dio
Pozdrav, kliknite na vezu u opisu. - Georgina, X8R Ltd
Merhabalar bunu yapıpta arıza kodundan kurtulan var mı?
Hi there, we have had lots of feedback from customers saying the fault has cleared after installing our kit. - Georgina, X8R Ltd
Never works with me
Hi there, did you purchase the kit and are having issues? If so, please email us at sales@x8r.co.uk
Ne posez pas cette piece, ce n'est pas durable car le collecteur a du jeu. il existe des entreprises qui refont correctement le collecteur.
Il s'agit d'informations inexactes, notre pièce peut être installée sans causer de problèmes. -Georgina, X8R Ltd
C'est toi qui le dit...@@X8RLtdUK
tdi 3.0 ??????
Hi there, we do a kit for the 3.0 TDI. Please see this link for the options available: x8r.co.uk/audi/inlet-intake-manifold-repair.html - Georgina, X8R Ltd