วีดีโอ

210 MW power plant me generator me seal oil system me discharge header pressure me variation aane ka kya karan ho sakta hai

Sir aap ka video killar dikhai nahi dheta

Black pen se Lika Karo ya white pen se

Ekadam shuddh nahin dikh raha hai

Cut in and cut out temperat😔

Sir mdbfp sqoop coupling mai warking oil temprecher badh ra hai to kya kare

Thank U Sir, For valuable information.

Thanks sir Aapne bahut acche se concept clear Kiya hai.

Sir number se continue battaye

Sir number to number battaye subse pahley kya kya start Kiya jata jai

Vaccum oil rank ke bare nhi bataye....

Thank you sir

Or load control master pr vedio banaya

Sir ohdr ky hota hai DCS me

Thank you sir

If wheel chamber pressure is lower than design than what is its significance

How much temperature considered?

Sir ji key phaser ka kya kaam hota hai ....?

Please make video for maintenance related

Sir why in post purg trip if furnace postive the why id tripping is given

In our plant coal is 400 TPH and we maintain 2100 TPH then it will be 5 kg .Is it correct

Sir y there is 30% CV and 100% CV.At what load & pressure change over will be done .is the pressure will be more than critical pressure to do change over in 660 MW

Sir plz make more videos.

Sir good morning Sir boiler commissioning ka video upload kijiye 660 mw

Sir as a boiler desk engineer, load ramp up or down me , boiler kaise behave karta hai , sh spray, burner tilt , ehtc , drum pressure kaise control karen, spray set point barana hai kab ghatana hai kab, metal excursion kaise prevent karen, , kindly explain, i have not getting concept clear where i work.please explain in a video . Or i want to clear in personal help.sir. Kindly give any contact

Sir please explain the purpose of small C and large C header in 2nd pass.

Thank you so much sir... Nice information..

Lube oil system ka video banao na sir aop jop acop etc please 🙏 abhibtak achha information video nahi bana hai

Sir.... 7:36 pr aap bole ki feeding change karega. M kah raha ki coal feeding change krega ki valve opening percent change krega.....? Kyonki ultimately pressure control tho valve se related hai na..... Bina feeding change kiye valve ka position change ho jaayga aur ref value of pressure mil jaayga??? Sahi socha ki nahi sir?

Sir, what are the problems that can arise while starting and stopping ldo gun? If it comes then how to handle it, make video on this also.

Ye burners k burnout ki kia reasons ho skti haan

Excellent ❤❤❤❤❤❤ sir

Sir please make a vedio about HPH & LPH charge on DCS

Working oil pump and lub oil pump voith coulping k inside hota hai??dono pump me kya difference hai?

S

dear sir, when we using pressure control mode operation and what is the turbine load for pressure control mode operation for 600 MW turbine.

Sir, please explain hydrogen circulation in generator and cold and hot gas temp.

Thank you sir.sir, please give the information regarding load sharing capacity of HP ,IP,LP turbine as stated like 26%,34,40 percent of each.so what is load share and which aspect like steam flow, energy etc.

Vedeo boht hi vadia laggia ji mein dekhia v te subscribed v kitaa ji 🙏 ❤

do you forget to arrest the winch ?😀

Sir What is the cavity temperature and why cavity fill up through water.

Sir BPA angel kitna hota h

Sir can we run unit full load with one FD FAN, what parameters we should watch

Very well informative sir ❤❤

Thank you sir for stating valuable information.sir,can you tell us about reasons for hp exhaust temperature high.

Sir, please explain about cold and hot gas temp.in generator

Fruitful information sir.sir,what will happen if coal layer secondary air opened greater than 20%

Very nice teaching Sir

Bfp mai booster pump kyo Diya rahata hai aur isako nahi rakha to kya hoga sir plg.jaldi bataiye