วีดีโอ

Cut the reversing valve right at the slide take a picture of discharge line orientation unsweat from compressor weld outside makes reversing valves go fairly smooth done a shitload on those Goodman’s definitely a challenge for sure if you have never done one

Chicken feed soldering

I miss installing commercial rooftop units! But residential will do for awhile 🔧

I'm a big Milwaukee fan myself.

Stick with it. There’s lots of videos. I think you’ll love it. Been using it for years. Most your issues are in the beginner videos

Very interesting

Damn! That thing is just dumping water !!!

It’s code to put on locking caps here in Ohio.

I just replaced a 29 year old Carrier gas-pack in my mothers house with a Trane gas-pack that looks just like this one. The dormer unit had this exact scenario; thermostat wire run under the pad and the yard maintenance guy chewed up the wire. One rainy night before it was replaced, the old Carrier unit kept turning the heat on and off intermittently even though the thermostat was turned OFF. I determined the chewed up thermostat wire was the culprit because rain was dripping down the wire, shorting the heat wires. When the new unit was installed, I explained that problem to the tech and he assured me hed reroute the thermostat wire so "it will never be able to get nicked again". He came through, and I thanked him. Whoever installed that original thermostat wire gave no thought to potential damage. My new thermostat wire is in a protective conduit! When I saw your video, it brought back bad memories!

Nice video man, but did you know you have some white guy on your video thumbnail ? 🙂 Has your account been hacked? LOL, jk.

us holding you accountable is making you a better technician lol

that filter drier is causing a small restriction since it's backwards, that's why your numbers are off

Crawl spaces!! Hell no!!!! Good job as always AB! Nice watch promo😅

What happens when the heat goes out If you have to remove the flue to get to the unit? I'd tell them they have to move the unit or I couldn't cover their service for heating.

Installers never seem to think about service

good video keep up the good work

I do what it takes to diagnose the issue. Luckily I never been in any crawspace other then low pitch roofs where the heat is right above you and roofing nails inches away from your head😂 I’ve seen filter dryers installed backwards as well.

Good job. Line set to small for 2.5 r22 system. 3/8x3/4 would be better. Good find on the wall cavity to the attic. That’s a big deal. You should have messed with the charge. It’s the small things that count. They add up. I was working on a 80 ton system today. Been told the unit is a pos. Well after looking through it, it really isn’t. It can’t work because the small things have not been taken care of. Nice vid.

Probably had high suction because it’s 90 degrees in the house. I think refrigerant was fine and like you said it was just a drain issues. Good stuff man I love seeing you work through it all 👏🏾🤟🏾

That coil looks backwards? Data tag is upside down. Made a v coil instead an a coil

My answer is down, mixing all the air. Unexcessible. However mayb unit is undersized and doesn't make it on a hot humid day.? I,ve installed drier backwards b4 inadvertently and it doesn't show any adverse operation. I would have probably balanced the air flow.

I'd refuse service until they gave me a key.

If it's working that well in the summer, I would have done what you did... on to the next one. (what a mess the air handler was under the house)

You say Baker app?

Hell no!

For one that small liquid line will drive your head pressure up crazy also

That's crazy they don't provide you with a key for the cages. Good job on those calls.

Believe me ur alot sharper than u think. I have alotta respect for how u do. Get some rest dog.

*Chirp There is a module repair kit I seen at johnstone. Don’t know any one that used one, But it might be worth trying it out on a newer motor instead of tossing it. *chirp

You should always check power with your multimeter first

Good stuff! Thanks for the video!

Spray foam the wall cavity.

Those cage are tough to work on lol Nobody never has the key.🤟💯🌎

I would pump it down, pull the indoor coil piston, replace with the next larger orface it will saturate the evaporator and cool the compressor.

You're not concerned that flex gas line in entering the furnace cabinet? Not hard piped out of the furnace cabinet?

you are a gret tec but damn u whine a lot

Is it just missing the door or did they bury the furnace behind the sheet rock wall because I’ve seen that before

They say you can mount some vertically and yes it plays a part, rule of thumb is 10 o’clock and 2 o’clock positions there is liquid and gas in those and it’s supposed to be level because liquid can flood the tail

So the quality of your calls go down at the end of the day…..I can put a Goodman too back on in 30 seconds, always take the door off and problem solved it’s not so difficult your quality of work is who you are and the company you represent you got some good videos but you have a few bad habits but hey you all good my man

12:05 sounds fine to me to be honest that’s how most of those rheem/ruuds sound plus you are not stupid everyone makes those mistakes!

dont let it overwhelm you, dont do the reports. just use them as a set of gages in fact use the gage button when logging in at a call. keep it simple give it a chance i hope you like it, check in next week, i work 10-15 hours a day, i use this almost every call. in and out. good luck. it is defiantly useful for you do not need to profile every call or any call. open it up use it as a set of gages. nothing more.

gray means your missing inputs. You needed an outdoor temp in addition to indoor wet bulb temp to get a target superheat for piston

estimated cfm or scfm is based on tonnage and temp split

too get seer you need voltages and amperages from your blue tooth meter or you could type it in

you have to mapp them in the tool box based on serial number thats why your return was 51 and your supply was 76 tool box bottom right

im 3 min in. just so you know, you really dont need to profile every call. often i dont. at a most i tell it if im working with a txv or piston, if you have a piston if you have an indoor psychrometer and outdoor temp it will give you a target superheat for charging. i do not put year tonnage seer and the rest of the mumbo jumbo every call. if you want estimated airflow you will need to input tonage and stuff, im telling you dude use it for a month make it second nature its killer

hell yeah my man, im just tunning in. excited to see how you like it

What kind of metering device does that unit have?

Did I mention that I HATE microchannel!

i cant believe the filter is in the floor