I like my FX dreamline so much that i'm considering selling it and stepping up a notch by getting a crown or impact instead... Fx makes some amazing rifles.
At 8:32 you remove a screw underneath which will allow you to separate the plenum from the rear. How would I separate the two if there is no bolt underneath? Awesome channel.
You probably have the side shot magazine system installed no ? The screw is underneath the magazine adapter plate . You can see what I mean in the disassembly video I made for the impact M3 . The step to remit that is identical
Excellent video, my Mk2 came with a power plenum, now I understand what that is a bit better, do you have a video about tuning for it, pellet selection, etc?
Great video, very clear and perfect angles to see what's going on and aesthetics. Thanks and keep up the stellar work ! Perhaps a video on the Slug power kit, installation and how it works exactly. Would you say it's compatible with the High Flow V2 Dual Hole Transfer Port and would use them together ?
thx for the support! I have a slug power kit to be installed , I will make a video about soon 😉 . First have to finish the new film studio. I use the High flow TP and the slug power kit will definitely be a good upgrade for it 👍
I have a "Pre" mk1....one of the first impact. This video is bassicaly for the old impacts??? The upgrade kits come with the new power block......I noticed you did not include it in this gun.
Thx for the support, FX is very kind to me and support to bring me these videos 👍 making this my main job from this is still a dream 😉 but who knows what the future might bring 🤷♂️ . The lube comes from Huma air , they sell this on there website
Hi , you are observing wel 👍🏻 . But I didn’t forget it , somewhere in the evolution of the impact FX decided to change the hammer insider eliminating the use of the C3 bumper that causes a lot of headache
What an outstanding video! I will echo what another commenter wrote "fx should hire you". I followed along and was able to do a power block/plenum install. I used the same fx gauge. Air leaks from the regulator area. Any idea what it may be?
@@Airbuks Thanks for your reply. It is coming from the regulator gauge area. It almost seems like from where the power block and the magazine bracket mate together.
@@alramos292 oke that’s not your regulator area , the reg sits behind the trigger . But if you have a leak between the plenum and the power block you should look at the orings inside the power block where the valve goed or the orings on the valve inside the plenum
@@Airbuks Yes sir. My apologies. I have edited my response to state the location is the regulator pressure gauge area. The fx regulator gauge was used from the original block to the power block. The o-rings were carefully seated and lubed with 100% silicone grease. Three in one hole and one in the other hole of the power block.
@@Airbuks The air leak around the regulator pressure gauge was due to a missing x ring seal on the power block kit. I appreciate your willingness to help me sir. I have subscribed to your channel!
Yes , make sure it’s flush and seated at the rear where the magazine goes, then the measurements of the valve rod at the front should be between 6-6,5 mm from the tip to the block of the impact
@@Airbuks Hi. Dont what am doing wrong but i cant get the front rod between 6-6.5mm what am i doing wrong here? I get 6.72 and i can’t screw it anyway more
@@FamilyFun183 first question? Do you use the original spring ? Do you have the slug power kit installed? Are you combining a high power Huma spring with the spacers from the slug kit ?
@@FamilyFun183 is your hammerspring ( small adjustment screw ) maxed out ? If you you will have to reduce it as it’s possible that is overdone slightly
On the barrel end going into the rear block, the barrel end (A4) has two holes in it. Does the bigger hole go in the direction of the regulator pressure gage ? Is it normal when seating the notch in the barrel end that it can go too far into the magazine area, blocking the magazine? Thanks, Appreciate your vids very much.
Hi I have a sub-12 ft lbs impact M3. Would I install power plenum the same as you have? Also that ft lbs would I be looking at after I have installed it? Thank you New Subscriber
Hi , thx for subscribing 👍 I don’t have any experience with sub12 😬 but I think the sub12 kit is a little different from the FAC one , I think there is a extra spring on the valve rod inside the plenum to help close that valve with the lower regulator pressure but I am not sure if that . Fx has done this on the early models of the impact but I am not sure if that is still the case
My power platinum leaks at the valve stem going into the body blowing air out the body. Do you guys think its the 2 black n white o rings in the power platinum cap?
Watch out as this upgrade kit did NOT fit my mk1. This is a known issue apparently but FX doesn't mention this anywhere. The diameter of the plenum in the kit is 12mm and the hole in my impact block is 11.93mm. There are batches that will NOT fit a MK1
Hi mate , thx for the comment. Yes indeed there are a few impacts out there that have issues installing the kit . But the problem isn’t the kit but the hole in the impact itself. There is a batch of impacts with a slight smaller diameter. FX is aware of this problem and if you encounter this problem send them a mail and they will provide you with a part for the plenum that will fit .
I used this video to disassemble my MKII Impact because of a leak. I noticed there was a moist build up in the plenum, thinking it was silcone. Should I clean the plenum out before reassembly. I did reassemble and the initial leak was gone for a few weeks but has come back. Could this be caused by the excess moisture in the plenum?
Hi I really appreciate the work you have done. I have a problem. I bought a impact mk2.35 I upgraded to the 720 power plenum. And I want to change my caliber to suit my daily needs. But I can’t find a video that explain how this mk2 .35 power plenum is different than say a mk2 pre power plenum. Explain how to disassemble the rifle with the 720. And drop caliber from .35 to .22 and .25 and .30. This is the last model of mk2. It’s been forgotten. Can you please help me out. With a new video or if you know of one can you please point me in the right direction. Thank YOU so much
Hi , I don’t own or have any experience with the 35cal 🤔 but the plenum is actually just a bigger volume and can be used for all calibers . But I don’t know if the hammer weight and spring is the same on a 35 cal compared to the rest . I just finished a video to be released in a few days upgrading my MKII with the plenum 720 and other M3 parts . I will ask my contact if there is a difference with the internals
I wanted to purchase the FX impact Mark 3 but I'm in Canada with tax it's going to be over $3,000. If I find a Mark II and install the power plenum what advantage would the Mark 3 have and is it much of a difference?
Airbuks....I have a question for you: I ordered my fx dreamline lite .22cal, 500mm stx barrel, 500cc aluminum bottle. In their website it specifically stated that .22cal comes with 500mm barrel...yet when i received the airgun it has a 600mm barrel. My question is: Is it possible that they made an error...changed the barrel to 600mm and send it to me? Because i feel that i've been played upon...that i bought a dreamline lite open-box; that what i bought has been used for testing or belonged to another person...it didnt have that look of a brand new item.
Hi, followed this but the alignment of the valve housing at one end and plenum end cap hole at the other is way out, meaning that the valve rod is not straight. Way out, like 130° out. I don't want to tighten the end cap more, and there is nothing to grip on anyway, and if I back it out by unscrewing to align the holes the rod goes through, the cap o-ring seal isn't made and air just rushes out. The alignment of the plenum end cap seems constrained by the cap and plenum thread, but that is allowing it to turn too far causing the misalignment. What am I doing wrong?
Have you made sure the valve housing ( silver tube ) is in the correct alignment with that tiny allenscrew ? If that is not perfect then everything else can’t be in the correct orientation
Hi there after installation power plenum from huma air I and huma regulator no 2 i have air going to barrel valwe look closed and I got 6,30 mm on front I'm not sure what it could be wrong
@@Airbuks Ok! I just ordered one. It is strange here in Sweden I can´t buy a liner but I can buy other trims for my gun. I would really like to get a proper slug liner. mine is in 600mm and that I have to use. we can only have 10 joules licens free wish is about 8 foot pound Not much to hunt with. Where do you live? I would love to go to Krale and shop until I drop lol. Thanks again for first class videos
I must be the most stupid man. I installed my power plenum but when I put the air bottle on it is leaking in the front en of the power plenum, What can I done wrong?
Ai 🫣 have you tried to cock the impact before putting your bottle on? The reason why it leaks from the barrel is that the valve isn’t closed and cocking might fix that . The plenum could be related as there isn’t any pressure build up because it leaks out of the barrel but it could have another reason aswel . Does the plenum leak between the threads of the plenum near the grip ?
@@lassesarnhult9283 I had the same problem once with the M3 after reassembling it . The depth to where you screw that front cap in is crucial. The face has to be exactly inline with the edge of the plenum. To deep or not deep enough and it will leak. Or that oring might be damaged 😬 you can also contact me true mail if you want to send a picture ( airbuks@icloud.com )
FX Impact There are many problems in Bangladesh. We don't get good results with this gun. Power, accuracy is good but needs to be repaired occasionally. The price of this gun is much higher in Bangladesh. Crown guns are much stronger but less powerful. It is important to upgrade the crown to more power.
The impact is a complex airgun , it needs to be maintained very good in order to make it function at high level . The crown has a simpler design with less orings 👍
@@Airbuks Dear friend, I have partially understood you. Impact guns are very powerful. And good guns, but why is it a problem again and again? I think the transformation of the Crown into a higher power is very important
@@armankhanjony7843 the impact is powerful thx to its design and adjustability. There for has many orings and so many possibilities to have one fail . The impact also needs to be tuned correctly and in harmony. If you use the wrong amount of reg pressure with the wrong amount of hammerspring you break things. The crown in its current configuration can’t be made as powerful as the impact but is abit more reliable since you almost can adjust it wrong and break stuff
I already say what i wanted to say, terrible view. For you is maybe fantastic to watch yourself in your fingers but what about the public? You think they want to watch your fingers or the all view from different angle
Dude, FX should hire you to do their videos...much better camera angles and more detail than what they put out...great job!
Thx for the support and kind words ! I try my best to keep bringing good content like I would like to find it if I was looking for it 👍
As always very well explained. For me this is the best description video on how to install the Fx impact power plenum. Well done in deed! 👍🏼👍🏼
Thx a lot for the nice comment 👍
You should have been a doctor. Thank you for all of your excellent videos. Just bought my first FX impact and I am amazed by this air rifle.
Thx for the support! Dokter 🤔 I prefer airguns they don’t complain 😂😉
Thank you, best and least confusing instructions on installation of the power plenum.
Thx 🙏🏻
I like my FX dreamline so much that i'm considering selling it and stepping up a notch by getting a crown or impact instead... Fx makes some amazing rifles.
The Dreamline is a amazing platform , I love it . I would never sell it but if you need the funds to by a Impact go for it 👌🏻
There are several of these videos out there. Yours is very well done in every way thanks much for sharing.
Thx 🙏🏻 I appreciate the support
Just intalled a power plenum on my mk1 following your video. So easy!!! Thanks for helping me out buddy 👍🤗
Nice 👍 your welcome
Very good explanation. Just 2 remarks : some lube on the o-ring from the valve and don't tighten the manometer so hard (it crushes the special o-ring)
Thx for the tips 👍
Fantastic job as usual. I was able to put mine back together thanks to you.
Thx mate love to hear that !
Excellent presentation, thank you very much, I look forward to the next one.
Very good video n well explained too … there’s no gun smith around here works on pcp’s … your videos really help… thank you 😊👍🏼
Thx for the support 🙏🏻 glad the video could help
Great videos, Keep up the fantastic information for fx users, Thank you,!!!
Thx 🙏🏻
Verry helpfull just followed this as I installed my power plenum and it was almost too easy with this video thanks 👍👍
Awesome, glad it helped 👍
Good tutorial indeed. Thank you!
Clear demo...understandable..less trash talk
Very well explained sir I really enjoyed watching it hope to c more videos keep it up 👍
Thx 🙏🏻
At 8:32 you remove a screw underneath which will allow you to separate the plenum from the rear. How would I separate the two if there is no bolt underneath? Awesome channel.
You probably have the side shot magazine system installed no ?
The screw is underneath the magazine adapter plate . You can see what I mean in the disassembly video I made for the impact M3 . The step to remit that is identical
Excellent video, my Mk2 came with a power plenum, now I understand what that is a bit better, do you have a video about tuning for it, pellet selection, etc?
If I could purchase an Fx Impact x and change to bigger plenum ..I would do it myself cause I clearly got your instruction.
Thx , glad the video gives you the confidence. It’s not that hard if you do it step by step and you are a little handy
Best video of them all of the plenum install 💯👌👍
Thx 🙏🏻
Great video. Is blue loctite enough for hammer seat? It won’t get loose?
Never had any issues with it and everytime I remove it I have to heat it to be able to undo it so I guess it fine 👍🏻
Great video, very clear and perfect angles to see what's going on and aesthetics. Thanks and keep up the stellar work ! Perhaps a video on the Slug power kit, installation and how it works exactly. Would you say it's compatible with the High Flow V2 Dual Hole Transfer Port and would use them together ?
thx for the support! I have a slug power kit to be installed , I will make a video about soon 😉 . First have to finish the new film studio.
I use the High flow TP and the slug power kit will definitely be a good upgrade for it 👍
I have a "Pre" mk1....one of the first impact. This video is bassicaly for the old impacts??? The upgrade kits come with the new power block......I noticed you did not include it in this gun.
This video was made before the upgrade power block was introduced
Great, clean and useful video....thx.
Thx
Awesome job !!! Like the other guy said FX should hire u man !!!! All your videos are top notch man!! What kind of lube did u use ??
Thx for the support, FX is very kind to me and support to bring me these videos 👍 making this my main job from this is still a dream 😉 but who knows what the future might bring 🤷♂️ .
The lube comes from Huma air , they sell this on there website
great vid ty but did you not forget the c3 bumper ?
Hi , you are observing wel 👍🏻 . But I didn’t forget it , somewhere in the evolution of the impact FX decided to change the hammer insider eliminating the use of the C3 bumper that causes a lot of headache
@@Airbuks great to know thankyou
What an outstanding video!
I will echo what another commenter wrote "fx should hire you".
I followed along and was able to do a power block/plenum install. I used the same fx gauge.
Air leaks from the regulator area.
Any idea what it may be?
Thx mate , I appreciate it 👍 where exactly is your leak originating from ?
@@Airbuks
Thanks for your reply.
It is coming from the regulator gauge area.
It almost seems like from where the power block and the magazine bracket mate together.
@@alramos292 oke that’s not your regulator area , the reg sits behind the trigger .
But if you have a leak between the plenum and the power block you should look at the orings inside the power block where the valve goed or the orings on the valve inside the plenum
@@Airbuks
Yes sir.
My apologies.
I have edited my response to state the location is the regulator pressure gauge area.
The fx regulator gauge was used from the original block to the power block.
The o-rings were carefully seated and lubed with 100% silicone grease. Three in one hole and one in the other hole of the power block.
@@Airbuks
The air leak around the regulator pressure gauge was due to a missing x ring seal on the power block kit.
I appreciate your willingness to help me sir.
I have subscribed to your channel!
When took the measurement for the valve rod (6.5) , did the rod need to be flush in the rear? Thanks for the video and nicely done
Yes , make sure it’s flush and seated at the rear where the magazine goes, then the measurements of the valve rod at the front should be between 6-6,5 mm from the tip to the block of the impact
@@Airbuks Hi. Dont what am doing wrong but i cant get the front rod between 6-6.5mm what am i doing wrong here? I get 6.72 and i can’t screw it anyway more
@@FamilyFun183 first question?
Do you use the original spring ?
Do you have the slug power kit installed?
Are you combining a high power Huma spring with the spacers from the slug kit ?
@@Airbuks nothing but the power plenum kitt
@@FamilyFun183 is your hammerspring ( small adjustment screw ) maxed out ? If you you will have to reduce it as it’s possible that is overdone slightly
What unit of measurement is your calliper reading? when reassembling you mention 6-6 and a half and then 44 is it millimetres?
Yes mm indeed
On the barrel end going into the rear block, the barrel end (A4) has two holes in it. Does the bigger hole go in the direction of the regulator pressure gage ? Is it normal when seating the notch in the barrel end that it can go too far into the magazine area, blocking the magazine? Thanks, Appreciate your vids very much.
Hi , not quite sure what you mean but the silver part on the back of the plenum should sit completely into the back block
Hey buddy .
My new mk 2 power plenum dumped all the air from the barrel with few mins . Need your help to figure out the problem. Thanks
Hi, any tip on how to unscrew my reg gauge as it's not moving?
Thanks
Try to remove the cover and use a socket
Hi I have a sub-12 ft lbs impact M3. Would I install power plenum the same as you have? Also that ft lbs would I be looking at after I have installed it?
Thank you
New Subscriber
Hi , thx for subscribing 👍
I don’t have any experience with sub12 😬 but I think the sub12 kit is a little different from the FAC one , I think there is a extra spring on the valve rod inside the plenum to help close that valve with the lower regulator pressure but I am not sure if that . Fx has done this on the early models of the impact but I am not sure if that is still the case
Is there a break in period if the power plenum is newly changed?
Not really after a few shots everything should be settling into place .
Great video!
Already done this but i watch it anyway 😃
Can you make a video of reseal a power plenum?
Thanks
Thx for the view count then 😉👍 , the day that I have to reseal mine I will make a video . I am not going to fix what’s not broken 😉
@@Airbuks thanks
After I reassembled my gun, the air those not get to the power plant. Theres air in the bottle, but can't fire the gun. What am I missing?
Did you adjust you back regulator pressure?
My power platinum leaks at the valve stem going into the body blowing air out the body. Do you guys think its the 2 black n white o rings in the power platinum cap?
Could be , but it could also be the 2 orings on the tube going into the body
Watch out as this upgrade kit did NOT fit my mk1. This is a known issue apparently but FX doesn't mention this anywhere. The diameter of the plenum in the kit is 12mm and the hole in my impact block is 11.93mm. There are batches that will NOT fit a MK1
Hi mate , thx for the comment. Yes indeed there are a few impacts out there that have issues installing the kit . But the problem isn’t the kit but the hole in the impact itself. There is a batch of impacts with a slight smaller diameter. FX is aware of this problem and if you encounter this problem send them a mail and they will provide you with a part for the plenum that will fit .
@@Airbuks thx!
I used this video to disassemble my MKII Impact because of a leak. I noticed there was a moist build up in the plenum, thinking it was silcone. Should I clean the plenum out before reassembly. I did reassemble and the initial leak was gone for a few weeks but has come back. Could this be caused by the excess moisture in the plenum?
The moisture probably will come from the air you put in it , do you use a hand pump or scuba tank ?
Where is the leak exactly?
@@Airbuks I have been using a Nomad II to fill the gun, until it went bad. I am now using the EC-3000. The leak was just behind the trigger housing
What power would a standard fx impact produce with a 600mm barrel in .22cal with a factory small plenum.
Hi I really appreciate the work you have done. I have a problem. I bought a impact mk2.35 I upgraded to the 720 power plenum. And I want to change my caliber to suit my daily needs. But I can’t find a video that explain how this mk2 .35 power plenum is different than say a mk2 pre power plenum. Explain how to disassemble the rifle with the 720. And drop caliber from .35 to .22 and .25 and .30. This is the last model of mk2. It’s been forgotten. Can you please help me out. With a new video or if you know of one can you please point me in the right direction. Thank YOU so much
Hi , I don’t own or have any experience with the 35cal 🤔 but the plenum is actually just a bigger volume and can be used for all calibers . But I don’t know if the hammer weight and spring is the same on a 35 cal compared to the rest . I just finished a video to be released in a few days upgrading my MKII with the plenum 720 and other M3 parts . I will ask my contact if there is a difference with the internals
I have asked and there shouldn’t be any difference in the internals 👍🏻 so just swap to different caliber and retune it
Hi there i have a problem with putting inside the o-ring into fhe powerblock where the chamber of the barrel is, any help or video please
I wanted to purchase the FX impact Mark 3 but I'm in Canada with tax it's going to be over $3,000. If I find a Mark II and install the power plenum what advantage would the Mark 3 have and is it much of a difference?
At what number can set regulator to working perfect ; because this regulator building to fx mk1 when added power pallinum working slowly to refilling.
Will installing the 72cc plenum be the same?
Procedure is almost identical I think , I have a 720 plenum in the way to upgrade my impact MKII and will make a video about that aswel
Do you know who has the 72cc power plenum in stock?
Do you know that there is a significant lost in power once you install this on the .357 mk2?
Airbuks....I have a question for you:
I ordered my fx dreamline lite .22cal, 500mm stx barrel, 500cc aluminum bottle. In their website it specifically stated that .22cal comes with 500mm barrel...yet when i received the airgun it has a 600mm barrel.
My question is: Is it possible that they made an error...changed the barrel to 600mm and send it to me?
Because i feel that i've been played upon...that i bought a dreamline lite open-box; that what i bought has been used for testing or belonged to another person...it didnt have that look of a brand new item.
Normally it comes with a 500mm barrel unless ordered specifically, but it’s more likely the swap or open box happened by the store you bought it from
Does this work with the FX Impact M3? :)
? You want to install the power plenum on the M3 , the M3 already has the 720 plenum ?
@@Airbuks not in my coutry. Here it wont come with that or moderator either.
@@thespectator2976 so you have a sub12 limit ?
Ps : yes it can be installed on a M3
Hi, followed this but the alignment of the valve housing at one end and plenum end cap hole at the other is way out, meaning that the valve rod is not straight. Way out, like 130° out. I don't want to tighten the end cap more, and there is nothing to grip on anyway, and if I back it out by unscrewing to align the holes the rod goes through, the cap o-ring seal isn't made and air just rushes out. The alignment of the plenum end cap seems constrained by the cap and plenum thread, but that is allowing it to turn too far causing the misalignment. What am I doing wrong?
Have you made sure the valve housing ( silver tube ) is in the correct alignment with that tiny allenscrew ?
If that is not perfect then everything else can’t be in the correct orientation
Hi there after installation power plenum from huma air I and huma regulator no 2 i have air going to barrel valwe look closed and I got 6,30 mm on front I'm not sure what it could be wrong
Fx impact m3
Me Patrocina uma dessas aí pois eu só tenho uma jade pro e a mola já está fraca
I love your videos!
Thx 🙏🏻
Is it the same on M3?
That’s the same power plenum as a FAC impact M3 yes
@@Airbuks Ok! I just ordered one. It is strange here in Sweden I can´t buy a liner but I can buy other trims for my gun. I would really like to get a proper slug liner. mine is in 600mm and that I have to use. we can only have 10 joules licens free wish is about 8 foot pound Not much to hunt with. Where do you live? I would love to go to Krale and shop until I drop lol. Thanks again for first class videos
@@lassesarnhult9283 I am from Belgium
@@Airbuks So not so far from Krale then :D
@@lassesarnhult9283 about a 3u drive one way 😉
thank you very much
👊
Very useful. Thanx a lot
I must be the most stupid man. I installed my power plenum but when I put the air bottle on it is leaking in the front en of the power plenum, What can I done wrong?
Ai 🫣 have you tried to cock the impact before putting your bottle on?
The reason why it leaks from the barrel is that the valve isn’t closed and cocking might fix that .
The plenum could be related as there isn’t any pressure build up because it leaks out of the barrel but it could have another reason aswel .
Does the plenum leak between the threads of the plenum near the grip ?
@@Airbuks Yes exactly where it leaks between the treads at the connection to the front part where the grip is
@@lassesarnhult9283 I had the same problem once with the M3 after reassembling it . The depth to where you screw that front cap in is crucial.
The face has to be exactly inline with the edge of the plenum. To deep or not deep enough and it will leak.
Or that oring might be damaged 😬 you can also contact me true mail if you want to send a picture ( airbuks@icloud.com )
Awesome how to video..
Thx
Joyful to watch.
Thx
Que posibilidad hay de que sea traducido al español
How much?
I am not a store 🤷♂️ check your local FX dealer for correct price’s
FX Impact There are many problems in Bangladesh. We don't get good results with this gun. Power, accuracy is good but needs to be repaired occasionally. The price of this gun is much higher in Bangladesh. Crown guns are much stronger but less powerful. It is important to upgrade the crown to more power.
The impact is a complex airgun , it needs to be maintained very good in order to make it function at high level . The crown has a simpler design with less orings 👍
@@Airbuks Dear friend, I have partially understood you. Impact guns are very powerful. And good guns, but why is it a problem again and again? I think the transformation of the Crown into a higher power is very important
@@armankhanjony7843 the impact is powerful thx to its design and adjustability. There for has many orings and so many possibilities to have one fail . The impact also needs to be tuned correctly and in harmony.
If you use the wrong amount of reg pressure with the wrong amount of hammerspring you break things.
The crown in its current configuration can’t be made as powerful as the impact but is abit more reliable since you almost can adjust it wrong and break stuff
first lube thread of thin stick than apply loctite ....
Loctide? There is only one spot to use loctide
@@Airbuks should not be any lube for thread to loctite work properly. it is the same you paint your car without washing it and degrease it
@@АлексПротасов-о9е fully agree but there is only one part I loctide and that’s the C1 on the valve rod no loctide for the rest
Next time try to put the camera on the moon maybe is gone be better view
? What are you trying to say , you need more close ups ?
I already say what i wanted to say, terrible view. For you is maybe fantastic to watch yourself in your fingers but what about the public? You think they want to watch your fingers or the all view from different angle
@@borceapostolovski372 🤣🤣😂 go watch something else then and don’t waist your time commenting
Then you go cleaning toilets and don't play some kind of guru without glue
Your hilarious 👍🏻
oo cervis guns
Luar biasa.. enggak punya uang untuk beli
I cringe every time you call silicone glue.
Other than that very nice video
🤔 do I say glue ?
@@Airbuks I heard glue about 10 times. Never heard silicone.
Replay and listen
Quickly listened to a few parts of the video an I say lube not glue ?
@@Airbuks I'm sorry. I only could hear luu. on my cellphone. My bad
Upgraded my Gen 1 Impact already, but I enjoyed the video.
@@stedyone1090 no worries, you got me worried for a sec