Hi Guys, I have a HT-450 Quad with a Naza GPS Controler Board, it was working very well until one of my motor seize whilw hovering at about 15 ft, came verticaly straight down to the ground. Fix the damage motor and motor mount and reprogram the Naza setting which seem to be simple, however went I try to start up the motor nothing happen. So I unplug the power of the Quad and then re-power, the Naza system is powering up, but no power is going to the RC Receiver. Anyone had that problem before??
It´s a lot better then the KK2 since it among other things have RTH implemented with is dam good but this DJI naza is or course way more expensive then the KK2but as i see it is well worth the money if you need these things. You can by it on DJI homepage or cheaper on ebay which i think is the exact same thing.
could you give me some help i was trying to follow your vidio above i got to 2mins 21seconds on mdl select and i pressed end by mistake could you give me information onhow to reset on my t8j thank you diane
hello, perfect movie !! the explanations are wonderful and easy to follw on this T8J. but I got a used T6J and there is the display and menu use not as easy because small display. I have to adjust the T6J to a hexakopter HMF s550 with NAZA and a Futaba R2006GS. I followed your first video (part1) and did all you told. now I am better than before, but I still have to programm my control unit !?!? do you also have a video from a T6J ??? nice wishes from Panama
Hi there, we appreciated the video and instructions very much, but we would like to understand a bit about the Gyro gains. Could you please explain about Pitch Roll Yaw and Vertical gains, and also, how the value change should affect quad or hexa functionalitie? thank you very much,
hi,whats your recomendation for mounting the 2 futaba Rx antennas? i now they must be at 90º angle between each other. this means that one of them must be Vertical, an the other horizontal? in your setup i think you have one attached to one arm, and the other is "free" in vertical . in the R2008SB manual says that the antenna should be away from ESC, motors, etc. does your setup just side by side to the ESC on this arm affects range? is there a better way to mount it? thanks.
I use DT5 for gain control as it offers a beep for each touch of the adjustment and you can't accidentally bump it. I also use DT6 as a 3rd 3way switch. You could also use DT5 as a 4th 3way switch.
This all works fine but I cannot work out how to get into compass calibration by the flicking the GPS/ATTI/MAN switch? When I do this the status of the LED changes to show what flight mode I am in but I cant get into the calibration mode. What am I doing wrong here? Thnaks.
hi there, really appreciate your videos :) they are very helpful! However, I have a question and hope you can give me some help: 1. I followed every step in your setup, however, I can't start up the DJI NAZA-M when pushed both sticks to the left bottom and right bottom to start the motors. What is it that I'm doing wrong? Thanks very much!
Interested in the Futaba. I have DX6i.....question. I can program the 6xi to have all flight modes with no 3 position switches available (only 2 position type switches available) ...why would you have to give up any flight modes with two 3 position switches available?
Hello, I am building a quadcopter with NAZA M-V2, FS-i6s tx and FS-iA6B rx. RC calibration on NAZA on the PC is fine except setting the control mode, I cannot move the slider until the GPS, Atti. or Manual area turn blue, The only way I can move it is changing the values on thefly mode but is not accurate and does not go where I want. The other main issue is that I cannot arm the motor nor start the motor test on NAZA on my PC. I am totally puzzled and run out of ideas what to do next. Linking motors to TX and RX only the motors work when testing them. I would much appreciate your opinion/advise on this.
Trash the FS-i6 and get a FrSky X-lite or Taranis QX7. you will thank me for that. FS is nothing but experimental grade stuff that does not work so good often.
I'm having an issue, fully installed naza on my s550 hex using the dt7, when I arm it throttles up real high and all the motors don't spin until I move the sticks around. any suggestions?
Hi Guys, I have a HT-450 Quad with a Naza GPS Controler Board, it was working very well until one of my motor seize whilw hovering at about 15 ft, came verticaly straight down to the ground. Fix the damage motor and motor mount and reprogram the Naza setting which seem to be simple, however went I try to start up the motor nothing happen. So I unplug the power of the Quad and then re-power, the Naza system is powering up, but no power is going to the RC Receiver. Anyone had that problem before??
With this futaba t8j radio what range gave you for fpv because i see this radio have internal antenna
Why do you use the transmitter is aeroplane mode and not heli mode? Does it make it easier to fly?
It´s a lot better then the KK2 since it among other things have RTH implemented with is dam good but this DJI naza is or course way more expensive then the KK2but as i see it is well worth the money if you need these things.
You can by it on DJI homepage or cheaper on ebay which i think is the exact same thing.
Plz how connect naza with remote jr xg11 help me plz
could you give me some help i was trying to follow your vidio above i got to 2mins 21seconds on mdl select and i pressed end by mistake could you give me information onhow to reset on my t8j thank you diane
hello, perfect movie !! the explanations are wonderful and easy to follw on this T8J. but I got a used T6J and there is the display and menu use not as easy because small display. I have to adjust the T6J to a hexakopter HMF s550 with NAZA and a Futaba R2006GS. I followed your first video (part1) and did all you told. now I am better than before, but I still have to programm my control unit !?!? do you also have a video from a T6J ??? nice wishes from Panama
If i would choose the cheapest alternative that have a good RTH function that the naza what should i then pick?
Hi there, we appreciated the video and instructions very much, but we would like to understand a bit about the Gyro gains. Could you please explain about Pitch Roll Yaw and Vertical gains, and also, how the value change should affect quad or hexa functionalitie?
thank you very much,
hi,whats your recomendation for mounting the 2 futaba Rx antennas? i now they must be at 90º angle between each other. this means that one of them must be Vertical, an the other horizontal? in your setup i think you have one attached to one arm, and the other is "free" in vertical .
in the R2008SB manual says that the antenna should be away from ESC, motors, etc. does your setup just side by side to the ESC on this arm affects range? is there a better way to mount it?
thanks.
I use DT5 for gain control as it offers a beep for each touch of the adjustment and you can't accidentally bump it. I also use DT6 as a 3rd 3way switch. You could also use DT5 as a 4th 3way switch.
This all works fine but I cannot work out how to get into compass calibration by the flicking the GPS/ATTI/MAN switch?
When I do this the status of the LED changes to show what flight mode I am in but I cant get into the calibration mode.
What am I doing wrong here?
Thnaks.
hi there, really appreciate your videos :) they are very helpful! However, I have a question and hope you can give me some help:
1. I followed every step in your setup, however, I can't start up the DJI NAZA-M when
pushed both sticks to the left bottom and right bottom to start the motors. What is it that I'm doing wrong?
Thanks very much!
Hi, what is that about (End Points) i understood everything but that part i got lost.
Interested in the Futaba. I have DX6i.....question. I can program the 6xi to have all flight modes with no 3 position switches available (only 2 position type switches available) ...why would you have to give up any flight modes with two 3 position switches available?
Hello, I am building a quadcopter with NAZA M-V2, FS-i6s tx and FS-iA6B rx. RC calibration on NAZA on the PC is fine except setting the control mode, I cannot move the slider until the GPS, Atti. or Manual area turn blue, The only way I can move it is changing the values on thefly mode but is not accurate and does not go where I want. The other main issue is that I cannot arm the motor nor start the motor test on NAZA on my PC. I am totally puzzled and run out of ideas what to do next. Linking motors to TX and RX only the motors work when testing them. I would much appreciate your opinion/advise on this.
Trash the FS-i6 and get a FrSky X-lite or Taranis QX7. you will thank me for that. FS is nothing but experimental grade stuff that does not work so good often.
That’s a shame but it make sense as these two transmitters are more reliable. Thank you
Hi, what does it mean when I plug in the USB cable and the LED goes dim? And I cannot connect to the naza assist?
i have the same setup just that i have a F550 will thjis config work ? still learning my friend .... great videos !
hay alishanmao i have dx6i and im having a problem whit getting all the flyit mods on my dx6i can u help me
You should have shown how u bind the futaba with receiver
Why GPS not in the middle of the top plate? Isn't that what DJI recommends?
Hi, are the servos connectect directly to the dji naza or there is some kinda amplifier?
Please tell how to contact you. I'm having problem with my drone setup.please help me
My new T8J switches are in a different order but I think I've got the hang of it. Thanks Ali. (Tom)
Ali can you please answer my messege on facebook i need your help
I'm having an issue, fully installed naza on my s550 hex using the dt7, when I arm it throttles up real high and all the motors don't spin until I move the sticks around. any suggestions?
Spektrum please.!
Not necesary, i got it.
Thanks a lot!! I saved much time by watching this! keep going!
I have a Futaba T7C do you have instructions on how to configure it to work with my DJI Naza M2 system?
***** I'm sure you knew how to configure your first radio with no help.
Thank you very much for the wonderful films
i have sent messege
nice work, thank you!
can i use turnigy 9x ?