Yes they are facing forward, and motor order is correct. Like I said it lifts off the ground, but thottle is passt 50%, and then it lifts off very quickly with very little extra throttle. I'm using 930kv motors with 10" props. I'm familiar with flying other controllers, like arducopter, but it doesn't behave that way.
Thank you very much for posting this video. I've finally got my F450/NAZA programmed,thanks to your video!!! On programming your gains so it can be remotely adjusted via X1 & X2, I have a Futaba 6EX and there are no extra dials that can be used for the gains. If I want to adjust the gains, will I have to hook up to the NAZA Assistant to adjust?
Thanks for your video, i didnt know the 30A Opto had to have wires switched, i found my Motor 4 Not Spinning in the Correct Way. HA! i am connected up to an APM 2.6 FC.
hey just got the F550 and naza m. i have finished set up according to the directions in the manual and with help from this video but when i go to fly the the craft bounces violently and is not holding altitude. any thoughts on what my problem is?
What gain settings did you end using for Basic and Atti modes? While hovering I have a slight wobble in my F550 with NAZA and I can't seem to figure out the best settings?
I cont figure out how to setup the control mode switch. I have the Dx6i transmitter and AR6210 Receiver. do you maybe have some kind of guide for me or tell me how to set it up on the transmitter for I have no clue :S thx.
With loiter and return to home, I have a DX8 which the AUX 2 switch has 3 positions.. Can I set it so if the one switch is " 0 = OFF, 1 = Loiter , 3 = Return to home"?
When i put mine on attitude mode. it automatically lands and the orange light blinks fast. only can fly on manual mode. so it wont let me do altitude hold. what am i doing wrong. i have a dx8
I have a JR9503, and the screen is not responding when I move the stick to calibrate and the control mode switch is in blue (A"). What do you think it could be the problem?. Thanks.
i just got this hex a and hooked every thing up and went to test it out when i started up the motors only 4 out of 6 spooled up until i got to about take off speed then the others came in . once in the air the who thing was very shaky and not smooth pleas help!!!
please help i just got this kit and i am having problems my UV light keeps blanking orange ....and when i log into the program on the bottom its flashing MC Output on ...how do i turn it off and green like yours?i never got the motors started up,what am i doing wrong?
i have a question on the installation can you help me for installation because te driver wont work i cant have any connection on the computer bur i have trouble for the tx installation
Hey man. I have got to this stage now with my TBS Discovery but the aileron slider doesn't respond at all. I have tried changing it to a different channel but still nothing. Any ideas?
i heard a pop/spark just as you were plugging in the battery. is that normal? i get that a lot and worries me that i may be doing something wrong or have a potential for a fire. is that supposed to happen?
Excellent video and very detailed instructions. Thank you for your work on this project.
Yes they are facing forward, and motor order is correct. Like I said it lifts off the ground, but thottle is passt 50%, and then it lifts off very quickly with very little extra throttle. I'm using 930kv motors with 10" props. I'm familiar with flying other controllers, like arducopter, but it doesn't behave that way.
I'm on the point to buy this multicopter, so thanks for sharing this information
great video !! nice loud audio!! hearing beeps in the demo videos is important.will watch more
Thank you very much for posting this video.
I've finally got my F450/NAZA programmed,thanks to your video!!!
On programming your gains so it can be remotely adjusted via X1 & X2, I have a Futaba 6EX and there are no extra dials that can be used for the gains.
If I want to adjust the gains, will I have to hook up to the NAZA Assistant to adjust?
Hi!! Thanks for your video! I have an F550 with Naza V2 and my controller is WFLY 07 but I can make it fly.. Can you help me with the gains? Thanks
Thanks for your video, i didnt know the 30A Opto had to have wires switched, i found my Motor 4 Not Spinning in the Correct Way. HA! i am connected up to an APM 2.6 FC.
very nice job. im buying one its on the way .
hey just got the F550 and naza m. i have finished set up according to the directions in the manual and with help from this video but when i go to fly the the craft bounces violently and is not holding altitude. any thoughts on what my problem is?
Is your NAZA facing forward? The M1, M2, M3 etc marks should face to the front of the multicopter...
Beautiful. Thanks.
What gain settings did you end using for Basic and Atti modes? While hovering I have a slight wobble in my F550 with NAZA and I can't seem to figure out the best settings?
is the JR XG8 radio enough and can control gains ? thanks
are you supposed to fly in attitude mode or manual mode?
I cont figure out how to setup the control mode switch. I have the Dx6i transmitter and AR6210 Receiver. do you maybe have some kind of guide for me or tell me how to set it up on the transmitter for I have no clue :S thx.
How did you getr GPS reception from inside a building?
Question on the battery, I looked up the one used and it does not come with the Deans connection, did you use and adapter?
Very Nice Video
Arrgh, I'm having problems with my Naza. It does lift off until I get over half throttle, and then it just jumps. Any idea, what's may cause that?
With loiter and return to home, I have a DX8 which the AUX 2 switch has 3 positions.. Can I set it so if the one switch is " 0 = OFF, 1 = Loiter , 3 = Return to home"?
Don't you need to throttle calibrate each ESC separately before using the naza assistance software program ?
@Soldier53flyer did u get it working
hi can i control gains with the JR X8 ? thanking you.
I get this slow yellow blink on on the VU LED on my F450. Do you know whats my problem is?
When i put mine on attitude mode. it automatically lands and the orange light blinks fast. only can fly on manual mode. so it wont let me do altitude hold. what am i doing wrong. i have a dx8
I have a JR9503, and the screen is not responding when I move the stick to calibrate and the control mode switch is in blue (A").
What do you think it could be the problem?.
Thanks.
hi can you help my f450 takes off fine but if I yar left or right it wonts to nose drive all the time
you went to fast in video you how switches are to be set on transmitter can you send me that info? i have a spektrum dx6i , thanks
i just got this hex a and hooked every thing up and went to test it out when i started up the motors only 4 out of 6 spooled up until i got to about take off speed then the others came in . once in the air the who thing was very shaky and not smooth pleas help!!!
please help i just got this kit and i am having problems my UV light keeps blanking orange ....and when i log into the program on the bottom its flashing MC Output on ...how do i turn it off and green like yours?i never got the motors started up,what am i doing wrong?
what "c" battery should you use?
hi how to put it to lock home mode ?
Hi, I have a F450 DJI Naza and I can not run the registration and I can not us it? how do you do the registration?
i have a question on the installation can you help me for installation because te driver wont work i cant have any connection on the computer bur i have trouble for the tx installation
how do you make slide switch to work?
I use APC 10x3.8 props w 4S Battery someone told me the 8x6'' Propeller is better performance w 4S battery ..that's true?
Hey man. I have got to this stage now with my TBS Discovery but the aileron slider doesn't respond at all. I have tried changing it to a different channel but still nothing. Any ideas?
Have you found the cause of your issue? I'm currently having a similar one.
hi, where did you get your controller
Get a DX8 or a Futaba 8FG TX you do not have all the switches on the DX6
I was able to do it with a DX7 using AR7000.
i heard a pop/spark just as you were plugging in the battery. is that normal? i get that a lot and worries me that i may be doing something wrong or have a potential for a fire. is that supposed to happen?
carbon fibers somehow do conduct electricity insulate your connectors from any CF attachments
can you have no auto piloot
How come my mc output is on and how do you turn it off?
+Edward Siyavong Did figure this out? I have the counter-problem. Mine is off and I want to turn it on... don't know how :-/
he hasn't installed any GPS.... just manual and attitude... Attitude is just a 'levelling' system, not a position system.
*****
Hi chris the motor directions are fine.also when i try to throttle up it tries to topple on the front props.
***** your motor rotation is wrong that's why it wants to flip
No i just checked the motor direction it is right.i got a lift in the attitude mode.
I still cannot get the gps calibration
Are all the motors arming at the same time? Did you calibrate the esc's?
How can I get that MC output light to turn off.?