DJI How to install Naza M V2 on F450
ฝัง
- เผยแพร่เมื่อ 30 ก.ย. 2024
- DJI adheres to continuous innovation and improvement. With the new firmware, new attitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude and attitude and therefore can be used for autopilot/automatic control.
Subscribe: www.youtube.com...
Like us on Facebook: / dji
Follow us on Twitter: / djiglobal
Follow us on Instagram: / djiglobal
Take a look at our website: www.dji.com/pro...
With all this continuous innovation and improvement why can't you make it work in Windows 10?
It works on W10...
Should not the bottom plate be rotated 90 degrees +/-.
Hi , I am a bit too late but I would like to ask You - what is the newest version of DJI Naza V2 these days and where can I buy it from ? I would apreciate an answer ,thank you in advance !
jajajajaja dji the plate is the wrong way!
You are an absolute Legend for this.. Very straight and concise set of instructions. Even the actual manual is not this clear about mounting. Thank you!
No information on the configuration or setup of this stupid flight control system. It does not work as easy as plug and play. In fact the setup assistant does not assist you on how to set it up!
Flying Typhoon It took me a while but I got it working. Also if you get the phantom rx/ tx it's just 1 wire.
bro one problem transmitter calibration is problem how to sole this bro
Yep... I just did a F350 build following the DJI videos and realised they have the plate all messed up... !!! Thanks for telling us DJI!!!
**Facepalm**
Lacked to show how can we to fix the GPS's spindle with holder lower and upper wtih GPS Bottom compass!
How do I use the dji controllers on the naza v2??
he doesn't even really have them on straight lol all that money and you higher someone dyslexic
Ok guys I have NAZA M v2 and Turnigy Multistar 45 Amp OPTO Controller on my hexa, can anybody tell me should I remove the red wire (+) from the controller or not?
The answer is NO, it is not necessary
why install the pmu way out there on one of the motors- surely keping all the mass in the middle near the cg is best ?
Style Review I’m super late but that was the led module not the pmu
Erm, typically the white is forwards direction, and the bottom plate is the wrong way around. Otherwise you get sideways mounted gimbal.
Joe Anthing i put white at the back and red in front, its supposed to be that way
Clorox Bleach Yeah I also done mine this way and thought it were wrong.
Sean. It points to the front of the quad.
how much does it matter that the gps antenna be mounted on the post as opposed to mounting it on the copter itself?
mgate01 there will be interference if u mount it directly to the aircraft, putting it on a stand teduces the interference
Clorox Bleach I have tested mounting flat and never had a problem with it. although my main one is mounted on the rod.
Thank you! Awesome vid!
Hi DJI, how do I have images of the drone f450 camera on the same phone as the Phantom, would it be possible to use the phantom wifi extender on the f450? ... Thank you
Anderson xavier nope u cant
Clorox Bleach Surely you can... I've built a f550 with the phantom rx / tx
Clorox Bleach, Joe Anthing Good friend, I also use the Rx and TX 5.8ghz of the DJI Phantom 2 Vision Plus on my f450 with the naza V2 but I'll make an attempt I have a phantom 2 wifi extender here and we'll see what's up !!! But thanks for the reply !!!!
Gee the flight controller and GPS/compass module were nearly pointing forwards.