I honestly don’t think you have to wait a week that’s just me everyone has there own way of doing I’ve painting many other things and havnt had to wait for a week a day or less sometimes but it’s how ever you choose to do it nice video👍
Yeah every paint is different. I was going by what this particular paint suggested on the can. You could easily get away with less. Although by one week you would expect it to be very hardend. Hand oils can be really tough on paint.
Very professional. Every video of this I've seen the people taking it apart are like. I think I need to unscrew this and then they look for extra screws to unscrew
Haha yeah I tend to take ages to make a video because I like to make sure I really know what I am doing before publishing anything. The downside is my videos are kinda sparse. But thanks for the encouragement anyway!
I know this video is pretty old so you may not see this, but can you paint the back without losing grip because the back and front plastic is different?
It really depends on the finish you go with. You can actually get a rubber based paint that would actually increase grip. But if you were going to use a standard paint the trick would be to thinly apply a coat of paint on the back as to not fill the grooves of the back plate.
I don’t usually sand the controllers I paint, i just use a good primer (gray or clear) and then i finish it off with liquitex acrylic spray paint which gives the controller a very nice matte-ish texture, plus being an high quality spray paint it’s very durable and has a great tone to it, if the customer wants a glossy finish I will layer some clear coating, but the liquitex finish is so great people usually just don’t want the clear coat. I know it kinda sounds like advertising but it is a really good product and I wish they paid me for saying this
Wouldn't use acetone because it dissolves many plastics. Notice how when you wiped it down, it became shiny again and you needed to sand again. That's because you basically took out the original scratches you made with the acetone. Isopropyl alcohol is plenty and won't screw things up. Acetone vapor is actually used to smooth out 3D printed models because it is such a powerful solvent.
+Geirlodnir It didn't remove any of the scratches but just created a film that covered them up temporarily. I agree that it's a very strong solvent and probably more than enough for the job but I wouldn't say that it can hurt anything in this scenario.
Very good, in-depth tutorial! All I'm doing is switching the front face between an all black and all white controller, so it shouldn't be too hard. I'll comment again later to say how it went! I was thinking of doing the same thing with a Wii U Pro controller, but the white ones are like $120(CAD) online so I may actually have to refer back to this tutorial and spray paint it!
"Why is this so hard to unscrew?" Probably because I'm screwing it clockwise. After I got past that moment of genius and got the back off (which makes a terrifying "oh god I broke it" sound), it was just as easy as replacing the backs for the most part. I was so worried I lost one of the springs for the L2/R2 triggers, but I found it! It took me a while to figure out that the loop on the spring went around the axle. One of the sticky tabs for the new controller just... wasn't there, but I'm sure that's fine. Lastly, on the secondary controller (which I took apart first in case I made a mistake), I pulled a little too hard taking it apart and the left side of the front came loose. I just had to remove the battery and jostle it back into place. In all, it went well and didn't take too long. I'll try out the controllers fully later, but they seem to be in great condition. Thanks for the tutorial! I'll Tweet you the finished product tomorrow.
@@dillonqaphsiel7977 Is it still holding up? Im on the fence about sanding, it obviously makes sense but that Rust-Oleum 2x works REALLY well on its own.
No worries. Also thanks for the nice comment. I love active viewers on my channel that comment and interact with me. Hope to see you around again in the future!
You mean on top of the paint? I guess so but make sure they are high quality. I have found not all permanent markers are equal. Also I would 100% use a sealant if you do that. Check my other video where I hydrodip a PS4 controller. I use a sealant on that one to lock in the colour. Works out really good.
@@TheGeekZone ohk thank you very much. One last question do you think ohuhu permanent markers (alcohol based) would work because they are quite high quality markers.
See if you can get a broken controller where the shell is still good. Customise it and if it works then move the working internals from your unmodified controller over to the shell of your newly customised one.
+ThePapadumGeek Yeah I was going to next level it and then add a layer of pearl over the top but I just wanted to get the video done as it was it was over a week long project to finish. I want to end up with 4 controllers (currently have two) for parties and group hangs etc. The plan is to paint all of them so they can all be identified easily. Which means I still have three controllers to paint. I want to also do a metallic one. Not a chrome but like a genuine metallic flek type paint.
Nice video very informative. I liked the color you choose and it matches some sneakers my nephew has and because if this he asked if I could paint his controller. My question is how long did this paint last on the controller, especially for "for a sweaty" playing call of duty like my nephew, I love him but ya know it's the truth. Lol Would adding multiple coats allow for extra protection and also would you advise on allowing 24 hours between coats and when done allow up to a week to dry? Thanks and you got a new sub right here.
I am still using mine with very little wear at all. As for the coats and dry time yeah 24 hours between coats and 1 week to dry. Any more coats and you'll most likely cause it to wear quicker. As the old saying goes "less is more". P.S thanks for the sub, glad you have you around.
I'm looking to do this for one of my PS4 controllers, but I have no idea how I'm supposed to pick the parts to replace the stock parts with. I read that it matters what type of controller you have, and I'm so confused. The model number is CUH-ZCT1U. Help?
Do you have any problems with the paint on the thumbstick rim chipping off? (Specifically the upward edge due to heavy use) How do I solve this problem? TIA.
Yes you will have this issue. The only reason the original controllers won't have this issue is because the colour is in the plastic. Anything you paint that grinds will eventually get wear like that. You tougher paints like enamels and do multiple coats in order to prolong the effect.
Love the color. Might take te idea and do it too. But with different color sticks. And do you really have to wait a full week for both coatings? Or just two days tops?
frank med a week is definitely overkill, you should be good with 24 hours, and between you and me i waited 6-7 hours, because it’s really hot out here, temperature does affect curing time
Yeah definitely but it would be a bit more complicated as there is more involved. You've actually given me a great idea to possibly make a video on this very thing.
The final finish will depend on how you sand, what paint you use and whether you decide to clear coat afterwards. But the answer is you can definitely make it feel the same as original.
question what if i didnt sand but just proceed spraying on it? like i do clean the casing just that no sanding is done and one more thing does it peel easily without primer applied?
Everything that I do is about achieving the maximum quality of the end result. Sanding creates a porous surface which helps the paint stick better. The primer also helps with this, you can choose to leave out these steps but you might find that within 6 months you are having to do the whole thing again.
Just because it's a ketone doesn't mean it can't be used as a rubbing alcohol. I used it with the intention to clean the plastic which happens to be the reason it was invented.
+john wickham OK sure I get what you're saying. But hey at the end of the day it does the job as intended. Thanks for pointing out my mistake. Hope that you are satisfied now? Cheers!
Do you have to sand it? I’ve never sanded before and know I’ll mess it up. I want to paint my controller white, and use a toothbrush to splatter black paint on it. I just wonder if it’d stick without sanding.
Initially it won't make much of a difference but in the long run it will help with maintaining the quality. The rough surface helps the paint to stick better. I find it one of the easier parts of the process though. You should be fine.
The Geek Zone alright! Thanks for replying so quick. I think I’m going to do this on one of my controllers tomorrow. I was planning on buying a new one anyways so it’s fine if I mess up.
so i have a ps4 controller that worked b4. when i try and play any game or send a psn message my R1,R2 and square buttons dont work. and i bought a shell for it when it work. it was put on by the business i bought it from. any helpful tips or fixes would be nice
+Tyland Glidewell Personally if you paid for someone to fit it for you I would asking them to make sure it worked properly. Otherwise just pull it apart and put it back together using my guide and see if that might help?
+Cheeky Manz unfortunately I've never been to Canada. Want to invite me? Try your local hardware store. It doesn't have to be the exact same brand. Just something similar.
+Cheeky Manz unfortunately I've never been to Canada. Want to invite me? Try your local hardware store. It doesn't have to be the exact same brand. Just something similar.
+Sevi Gonzalez I'd say the sanding is pretty important as a porous surface is kinda essential for getting the paint to stick. What will tend to happen if you paint straight on to a smooth surface is that the paint will most likely peel off down the road. This will be doubly so if it's a controller that has been used and has a surface coated in hand oils also. It's fairly cheap and readily available at any hardware store. Do yourself a favour and just wait to get some sandpaper.
+Akshpreet Hayer I didn't use a clear coat because the paint I used is very durable and can withstand the wear and tear it's likely to receive under normal use. Can you use clear coat to give it that little extra protection with the added bonus of being able to select the final sheen. With clear coat you can pick something from very matte through to very shiny to get the desired look you are going for. Personally I like a semi-gloss as it starts to look a bit cheap when it's really glossy or shiny and a matte finish can also look nice but really is colour dependant. I hope that helps you out a bit?
The paint that I used is very durable, but if you were to do what you were saying then it would be even better. Give it a crack and show me how you went. Tag me on whatever social media you post it to.
If you prime, use good paint and apply correctly it should last for hundreds of hours in the hand. I've recently started coating the finished product with clear and it helps with longevity.
Does primer really make such a big difference because i just came back from the store and realized i forgot it and i am wayyy to lazy to go back. If it does, how?
Yeah I found that the white controllers do seem a bit tougher to get off myself for some reason. Just squeeze the grip a little hard. It will eventually come off don't worry.
At best you’ll lose sensitivity in the touch pad. At worst it will stop working altogether. The click function will keep working regardless. So if you want to use it as a button and don’t care about touch controls then yeah. Otherwise no.
Nah I don't think so. It would only feel that way if it was over applied and not dying properly. You only want to paint it so that it just covers all the surfaces and not go overboard with it.
can i dip my controller into the bucket of paint color that i want? pull it out would be nicer color paint on my controller?lol i would paint the back same color as the front yellow?
it's really only necessary if you have used the controller before. it's mainly to get hand oils and grease off. if you painted it straight out of the box it would probably be fine but I'd still recommend you use a primer.
huh, interesting. When I painted GC controllers I just used water and a paintbrush to clean them, along with sand paper. I did use primer, but only with paint that needed it (eg paint that comes with primer in it)
+Lance Shuler All paints should really need a primer just some come in a 2in1 like the one I used. however it might take a long time to see the benefit of that like greater than a year. if you're really vigilant with the brush and soapy water then sure that will probably work too. Generally the rubbing alcohol will just make your life easier. It's like the saying about the right tool for the right job ya know. I'd love to see some of your work. You should post and tag me on twitter.
On the areas where the newspaper is stuck I would go back to sanding and using rubbing alcohol to removed any of the attached stuff and ruined paint. Then just go over that section again with the paint and primer smoothly spraying on to blend in with the rest of the controller.
I think some paints can get like that but if you use a really strong enamel and clear coat it then I don't think it will get that way. Mine did not even after 100+ hours of gaming.
Some of my buttons are stiff (ps, options, share) and the r2 trigger doesn't work ): anyway I can fix this I only have 2 controllers did not expect to brake it
Same thing happened to me the first time I opened my controller as well. Try losening off the two screws either side of the touch pad just slightly and see if that improves things for you?
Yeah I had to take off the back and press down the motherboard so all the buttons get in place. Be careful when prying off the the case as the triggers can snap off, they click back into place and work as long as the gel button is also wrapped over the plastic (if you get this problem you will understand). Works perfectly now and looks great! Also I would advise a couple coats of primer / white spray paint before you pick your colour.
Why was acetone used? All that does is melt the plastic and the sanding scratches. Wouldn't you rather just use alcohol to clean it instead of remove the scratches? I use acetone after 3D printing plastic parts to melt the rough surfaces into glossy surfaces.
It sounds like the paint did not dry properly or too much was applied. I'd sand it back again and use more rubbing alcohol to get as much off as possible. Then paint it again but really lightly just enough to cover the surface. Let it dry for like 24 hours and then do the same thing again. Depending on your climate, if it's quite cold you'll need to wait longer in between coats and even maybe just have some warm air blowing on it from a good distance.
I honestly don’t think you have to wait a week that’s just me everyone has there own way of doing I’ve painting many other things and havnt had to wait for a week a day or less sometimes but it’s how ever you choose to do it nice video👍
Yeah every paint is different. I was going by what this particular paint suggested on the can. You could easily get away with less. Although by one week you would expect it to be very hardend. Hand oils can be really tough on paint.
You have a good taste in colors
Thanks man
It’s called Key Lime Gloss by Rust-o-leum
I like how you used that card board box as a make shift paint booth.... Great idea.
Dude you're like the Bob Ross of controller costumization. Subscribed.
I chuckled at that comment. Welcome to the family!
paint job is dope
Yeah I really like it!
Very professional. Every video of this I've seen the people taking it apart are like. I think I need to unscrew this and then they look for extra screws to unscrew
Haha yeah I tend to take ages to make a video because I like to make sure I really know what I am doing before publishing anything. The downside is my videos are kinda sparse. But thanks for the encouragement anyway!
Awesome video. Thank you for boosting my confidence in customizing my own!
That’s awesome. Such a good feeling having a completely unique controller that you customised yourself hey?
I did it and I paint it gold bright,shiny and soft bright gold paint
That sounds great. Post in on twitter and tag me @stumbows
That looks awesome!
Deborah G. Thanks Deborah!
Great video. Didn't worry about my controller with this thanks for uploading!!
Thanks for encouragement. It a good feeling having a unique controller that you modded on your own.
yeah ive been trying to get the gf playing games. I bought a purple set of buttons to see if she'd like, she does
Haha it's always a challenge to get the mrs playing games with ya. Good work if you can make it happen.
I know this video is pretty old so you may not see this, but can you paint the back without losing grip because the back and front plastic is different?
It really depends on the finish you go with. You can actually get a rubber based paint that would actually increase grip. But if you were going to use a standard paint the trick would be to thinly apply a coat of paint on the back as to not fill the grooves of the back plate.
great! although ive never seen any non oil based paint product that recommends a full week for dry time.
I don’t usually sand the controllers I paint, i just use a good primer (gray or clear) and then i finish it off with liquitex acrylic spray paint which gives the controller a very nice matte-ish texture, plus being an high quality spray paint it’s very durable and has a great tone to it, if the customer wants a glossy finish I will layer some clear coating, but the liquitex finish is so great people usually just don’t want the clear coat. I know it kinda sounds like advertising but it is a really good product and I wish they paid me for saying this
Amazing video brother just did mine and it could not look better
Wouldn't use acetone because it dissolves many plastics. Notice how when you wiped it down, it became shiny again and you needed to sand again. That's because you basically took out the original scratches you made with the acetone. Isopropyl alcohol is plenty and won't screw things up. Acetone vapor is actually used to smooth out 3D printed models because it is such a powerful solvent.
+Geirlodnir It didn't remove any of the scratches but just created a film that covered them up temporarily. I agree that it's a very strong solvent and probably more than enough for the job but I wouldn't say that it can hurt anything in this scenario.
THIS is amazing! So going to try this!!!
Very good, in-depth tutorial! All I'm doing is switching the front face between an all black and all white controller, so it shouldn't be too hard. I'll comment again later to say how it went! I was thinking of doing the same thing with a Wii U Pro controller, but the white ones are like $120(CAD) online so I may actually have to refer back to this tutorial and spray paint it!
"Why is this so hard to unscrew?" Probably because I'm screwing it clockwise.
After I got past that moment of genius and got the back off (which makes a terrifying "oh god I broke it" sound), it was just as easy as replacing the backs for the most part. I was so worried I lost one of the springs for the L2/R2 triggers, but I found it! It took me a while to figure out that the loop on the spring went around the axle. One of the sticky tabs for the new controller just... wasn't there, but I'm sure that's fine. Lastly, on the secondary controller (which I took apart first in case I made a mistake), I pulled a little too hard taking it apart and the left side of the front came loose. I just had to remove the battery and jostle it back into place. In all, it went well and didn't take too long. I'll try out the controllers fully later, but they seem to be in great condition. Thanks for the tutorial! I'll Tweet you the finished product tomorrow.
+Nate3417 Hey thanks for the update, glad it helped you out and I can't wait to see your version of the controller.
I don't primer or sand just put a few layers on
How'd it work out?
The Geek Zone holds up nice
@@dillonqaphsiel7977 Is it still holding up? Im on the fence about sanding, it obviously makes sense but that Rust-Oleum 2x works REALLY well on its own.
Yo I can't wait that long 😂
It was hard for me too, but trust me it is worth it!
wow that's a very nice controller liked and subscribed
Welcome to the channel, glad to you have you around. I love bright colours especially lime so I'm very happy with it.
dude finally one that actually looks good. btw i just subbed.
+sd1rager Thanks man, appreciate the kind words.
The Geek Zone same
OK my bad! didn't notice! good job bro the finish looks great.
No worries. Also thanks for the nice comment. I love active viewers on my channel that comment and interact with me. Hope to see you around again in the future!
not just saying this but I definitely will try this! Looks awesome and a bit of fun as well. Video looks really professional as well :)
What about alcohol markers on top of it? Also should you put some kind of sealant on it?
You mean on top of the paint? I guess so but make sure they are high quality. I have found not all permanent markers are equal. Also I would 100% use a sealant if you do that. Check my other video where I hydrodip a PS4 controller. I use a sealant on that one to lock in the colour. Works out really good.
@@TheGeekZone ohk thank you very much. One last question do you think ohuhu permanent markers (alcohol based) would work because they are quite high quality markers.
I really want to,do this but I feel like I’ll mess it up
See if you can get a broken controller where the shell is still good. Customise it and if it works then move the working internals from your unmodified controller over to the shell of your newly customised one.
That's an awesome colour, might have to try this with some glow in the dark paint hhahaha
+ThePapadumGeek Yeah I was going to next level it and then add a layer of pearl over the top but I just wanted to get the video done as it was it was over a week long project to finish. I want to end up with 4 controllers (currently have two) for parties and group hangs etc. The plan is to paint all of them so they can all be identified easily. Which means I still have three controllers to paint. I want to also do a metallic one. Not a chrome but like a genuine metallic flek type paint.
Hello, I just want to know where did you purcahse the new housing for PS4 controller in your video.
Thanks in advance!
I bought it from AliExpress
wooow what an amazing color ..really nic review :-)
Nice video very informative. I liked the color you choose and it matches some sneakers my nephew has and because if this he asked if I could paint his controller. My question is how long did this paint last on the controller, especially for "for a sweaty" playing call of duty like my nephew, I love him but ya know it's the truth. Lol Would adding multiple coats allow for extra protection and also would you advise on allowing 24 hours between coats and when done allow up to a week to dry? Thanks and you got a new sub right here.
I am still using mine with very little wear at all. As for the coats and dry time yeah 24 hours between coats and 1 week to dry. Any more coats and you'll most likely cause it to wear quicker. As the old saying goes "less is more". P.S thanks for the sub, glad you have you around.
I'm looking to do this for one of my PS4 controllers, but I have no idea how I'm supposed to pick the parts to replace the stock parts with. I read that it matters what type of controller you have, and I'm so confused. The model number is CUH-ZCT1U. Help?
That depends on what part you are replacing. What are you planning to do?
I've been thinking of painting mine orange, maybe i will
Do it, I love orange!
Where did you get the thumbs sticks from?
eBay my dude.
Omg hope it works man i just painted my CONTROLLER
Very nice, post a picture and tag me in it.
Did it work?
Just did this with the yellow rustoleum I think you used lime green anyways thanks man, turned out great
Thanks for the video I’m making a pink one for my girlfriend
I want the metallic red and blue controller shell.
It looked great when I first got it but it peeled far quicker than my own paint job. I wouldn't buy one again.
Can I use clear coat will it help last longer ?
Yes that's what I have done in the later controller mods I have done. It definitely helps a lot.
how does the controller feel after spraying it with that spray paint? did the paint peel off? what if i spray primer first? will that be even better?
Yeah not too bad, definitely a different texture to the plastic that was there before but still nice.
Do you have any problems with the paint on the thumbstick rim chipping off? (Specifically the upward edge due to heavy use) How do I solve this problem? TIA.
Yes you will have this issue. The only reason the original controllers won't have this issue is because the colour is in the plastic. Anything you paint that grinds will eventually get wear like that. You tougher paints like enamels and do multiple coats in order to prolong the effect.
The Geek Zone Thanks for the reply dude. Really appreciate it.
The color it’s very cool 😎and keep going
My psn button to turn the controller on doesn’t look as far out as it did before and it won’t turn on. Any advice?
Open it back up and check the membrane behind the button is placed in properly.
Love the color. Might take te idea and do it too. But with different color sticks. And do you really have to wait a full week for both coatings? Or just two days tops?
frank med a week is definitely overkill, you should be good with 24 hours, and between you and me i waited 6-7 hours, because it’s really hot out here, temperature does affect curing time
Would this work with the PS4 slim itself? I was thinking about painting the console grey.
Yeah definitely but it would be a bit more complicated as there is more involved. You've actually given me a great idea to possibly make a video on this very thing.
Cool. it would be the only video on TH-cam that covers it!
If you were to do the back piece as well, would sanding it ruin the texture the backing already has? 😮
+Flossy Panda most likely yes. But you could use cleaning alcohol instead and just paint straight over the plastic that may work but no guarantee.
+The Geek Zone thanks 😄
Does the controller have a smooth surface like before you customised it?
The final finish will depend on how you sand, what paint you use and whether you decide to clear coat afterwards. But the answer is you can definitely make it feel the same as original.
was it just you'r preference just to do the top or can you do the bottom too?
Yeah I really loved the look of Black and Lime Green but there's no reason you couldn't do the entire controller.
Thx for the detailed how too
Thx so much
You're welcome!
I just got the next generation DS4 would it be okay not to sand it down? I've noticed the coat is a little more matte than the original.
Yeah if you sand it first it will be fine.
question what if i didnt sand but just proceed spraying on it? like i do clean the casing just that no sanding is done
and one more thing does it peel easily without primer applied?
Everything that I do is about achieving the maximum quality of the end result. Sanding creates a porous surface which helps the paint stick better. The primer also helps with this, you can choose to leave out these steps but you might find that within 6 months you are having to do the whole thing again.
Will I have to paint it again after some time?
If you do the job properly it should last a very long time. I put 400-500 hours on mine since painting it and it's held up just fine.
Acetone isn't rubbing alcohol. It's from the Ketone family of compounds.
Just because it's a ketone doesn't mean it can't be used as a rubbing alcohol. I used it with the intention to clean the plastic which happens to be the reason it was invented.
My point is it isn't alcohol, you can call a dog a cat but it's still a dog.
+john wickham OK sure I get what you're saying. But hey at the end of the day it does the job as intended. Thanks for pointing out my mistake. Hope that you are satisfied now? Cheers!
I don't think anyone cares what it's called, really.
Cheers man!
Do you have to sand it? I’ve never sanded before and know I’ll mess it up. I want to paint my controller white, and use a toothbrush to splatter black paint on it. I just wonder if it’d stick without sanding.
Initially it won't make much of a difference but in the long run it will help with maintaining the quality. The rough surface helps the paint to stick better. I find it one of the easier parts of the process though. You should be fine.
The Geek Zone alright! Thanks for replying so quick. I think I’m going to do this on one of my controllers tomorrow. I was planning on buying a new one anyways so it’s fine if I mess up.
Also have you tried hydro painting? I might try that I’m just not sure about it and what it entails.
I haven't but I've always wanted to. Might give it a go and make a video about it.
I have a silly question. Do you think I could use nail polish remover since it's acetone based?
I suppose you probably could. You could try it. Worst case it doesn't work and you just need to buy some proper stuff from hardware store.
For someone who hasn't taken apart a controller or any components would this be difficult? Great vid!
+Grim Reaper No not at all. This was only my second time taking one apart. With this guide you should be right.
Awesome and would it be easier to use primer instead of sanding or should you sand it anyway?
+GrimReaper Games Sanding helps the primer stick to the surface. The primer helps the paint stick to it.
Henry Chafe not at all
could I just use sand paper and alcohol and then put tape over the buttons and holes of the control then paint it?
You might as well take it apart the phillips #000 is only like 4$
Yes I agree with JinLee. Taping the buttons would require a lot of precision and effort. It will be a lot easier to take it apart and do it that way.
I’ve been trying to separate the top from the bottom for like 30 minutes now and I can’t get it
Does it matter of the type of sandpaper
A more coarse sandpaper will create ridges and grooves. A finer sandpaper will create a nice smooth finish.
so i have a ps4 controller that worked b4. when i try and play any game or send a psn message my R1,R2 and square buttons dont work. and i bought a shell for it when it work. it was put on by the business i bought it from. any helpful tips or fixes would be nice
+Tyland Glidewell Personally if you paid for someone to fit it for you I would asking them to make sure it worked properly. Otherwise just pull it apart and put it back together using my guide and see if that might help?
do you know where to buy the spray in Canada?
+Cheeky Manz unfortunately I've never been to Canada. Want to invite me? Try your local hardware store. It doesn't have to be the exact same brand. Just something similar.
+Cheeky Manz unfortunately I've never been to Canada. Want to invite me? Try your local hardware store. It doesn't have to be the exact same brand. Just something similar.
+The Geek Zone oh thanks!
Is it necessary to sand the shell? I have the paint with me but no sandpaper and I was just thinking about just painting it.
+Sevi Gonzalez I'd say the sanding is pretty important as a porous surface is kinda essential for getting the paint to stick. What will tend to happen if you paint straight on to a smooth surface is that the paint will most likely peel off down the road. This will be doubly so if it's a controller that has been used and has a surface coated in hand oils also. It's fairly cheap and readily available at any hardware store. Do yourself a favour and just wait to get some sandpaper.
Oki Doki, will do. Thank you very much for the help.
wat should you do after the secend sandpaper Job?
Just wipe it down to remove any residue.
Can i get a link to where you bought the paint?
+lasse085 Sorry I just bought it in store so don't have any links but search for Rust-Oleum 2x and I am sure you can find it online.
Can it be a mat finish
Yeah just buy a matte clear coat to go over the top with.
Did you use a clear coat and is it necessary?
+Akshpreet Hayer I didn't use a clear coat because the paint I used is very durable and can withstand the wear and tear it's likely to receive under normal use. Can you use clear coat to give it that little extra protection with the added bonus of being able to select the final sheen. With clear coat you can pick something from very matte through to very shiny to get the desired look you are going for. Personally I like a semi-gloss as it starts to look a bit cheap when it's really glossy or shiny and a matte finish can also look nice but really is colour dependant. I hope that helps you out a bit?
How durable is this paint that you used? I'm considering doing this too, but I may end up doing a coat of clear as well and sanding between coats.
The paint that I used is very durable, but if you were to do what you were saying then it would be even better. Give it a crack and show me how you went. Tag me on whatever social media you post it to.
Hi, have a link for the replacement xbox one joysticks. Thanks
I got mine from eBay. Just search Xbox sticks. I paid like $4 for 10 pack.
I cant do this, its too hard to put all the buttons back in place, I broke a cheap controller doing this.
Where can I get those sticks
I just bought them on eBay.
This is very informative, how long does the paint gonna last though?
A week before you get yellow paint rubbed off on your hands
If you prime, use good paint and apply correctly it should last for hundreds of hours in the hand. I've recently started coating the finished product with clear and it helps with longevity.
Damn, you have good skills!
THE BEST....! CONTROLLER FOR PLAYING PS4 IT SELF AND IT'S GAMES
Yeah PS4 controller is my favourite!
Does primer really make such a big difference because i just came back from the store and realized i forgot it and i am wayyy to lazy to go back. If it does, how?
+The Geek Zone and how many coats of primary do i need?
Ok I bought white primer and a color....my colored paint says paint+primer...so..would using my actual white primer be bad?
It's not going to be bad it's just not necessary.
Yas now i can finally make my DS4 black
Any tricks to remove the spray paint?
Using a rubbing alcohol or turpentine will get the spray paint right off.
How would u stick like a logo on the controller??
EskiBoy1 put it on, then put a clear coat of spray paint over it to seal it on
I have a white controller, one side of the controller pops off easily and the other side won't budge
Yeah I found that the white controllers do seem a bit tougher to get off myself for some reason. Just squeeze the grip a little hard. It will eventually come off don't worry.
What Grain of Sandpaper are you using?
+Cain D Grantham Pretty sure I was using at least 1000 grit.
Did you use any paint fixer after paint it?
+Carlos Gaitan No I didn't use anything after painting the controller.
Can i use acrylic?
Enamel is more durable in the hands. You can use Acrylic but I'd suggest coating with clear enamel if possible for maximum durability.
Can I paint the touch pad?
At best you’ll lose sensitivity in the touch pad. At worst it will stop working altogether. The click function will keep working regardless. So if you want to use it as a button and don’t care about touch controls then yeah. Otherwise no.
Does the controller feel sticky?
Nah I don't think so. It would only feel that way if it was over applied and not dying properly. You only want to paint it so that it just covers all the surfaces and not go overboard with it.
U
U
U
The usual one was probably painted just like that so it will not.
How long will this paint job last?
+ChadfusiousSays I'm not quite sure, as it will depend on how much you play but a really high quality paint should last for a very long time.
i'm just gonna paint it with a model brush and enamel. this look too risky but nice video.
Nice dude, let me know how it turns out.
can i dip my controller into the bucket of paint color that i want?
pull it out would be nicer color paint on my controller?lol
i would paint the back same color as the front yellow?
The spray will give a nicer finish because of the layers. When you dip you can't layer it meaning you don't have the hold or the even finish.
I've been seeing a lot of use of acetone while painting new controllers. I paint controllers and have never used it. Whats the benefit of using it?
it's really only necessary if you have used the controller before. it's mainly to get hand oils and grease off. if you painted it straight out of the box it would probably be fine but I'd still recommend you use a primer.
huh, interesting. When I painted GC controllers I just used water and a paintbrush to clean them, along with sand paper. I did use primer, but only with paint that needed it (eg paint that comes with primer in it)
+Lance Shuler All paints should really need a primer just some come in a 2in1 like the one I used. however it might take a long time to see the benefit of that like greater than a year. if you're really vigilant with the brush and soapy water then sure that will probably work too. Generally the rubbing alcohol will just make your life easier. It's like the saying about the right tool for the right job ya know. I'd love to see some of your work. You should post and tag me on twitter.
i painted mine but newspaper got on it and its all gooey and messed up. what do i do? help please
On the areas where the newspaper is stuck I would go back to sanding and using rubbing alcohol to removed any of the attached stuff and ruined paint. Then just go over that section again with the paint and primer smoothly spraying on to blend in with the rest of the controller.
Just noticed that you don't specify which way the membranes are supposed to face upon reassembly.
They only go in one way so you can't mess it up.
The reassembly was a success 😃
Do you like sticks of xbox one elite controller in modding?
I've never used them but would love to get my hands on an elite controller to test it out.
Did the controller got sticky with the paint? Btw awesome job I’m trying to do the same exact thing
I think some paints can get like that but if you use a really strong enamel and clear coat it then I don't think it will get that way. Mine did not even after 100+ hours of gaming.
The Geek Zone thanks appreciate it!
I ain't waiting a week
A day or two should suffice
Waiting times are heavily dependent on the quality and tipe of paint you use
Is acrylic paint fine?
Alex C sure is
Some of my buttons are stiff (ps, options, share) and the r2 trigger doesn't work ): anyway I can fix this I only have 2 controllers did not expect to brake it
Same thing happened to me the first time I opened my controller as well. Try losening off the two screws either side of the touch pad just slightly and see if that improves things for you?
Yeah I had to take off the back and press down the motherboard so all the buttons get in place. Be careful when prying off the the case as the triggers can snap off, they click back into place and work as long as the gel button is also wrapped over the plastic (if you get this problem you will understand). Works perfectly now and looks great! Also I would advise a couple coats of primer / white spray paint before you pick your colour.
Yeah I used a paint plus primer in one so it wasn't essential for me but yes a primer is usually required for stuff like that.
Why was acetone used? All that does is melt the plastic and the sanding scratches. Wouldn't you rather just use alcohol to clean it instead of remove the scratches? I use acetone after 3D printing plastic parts to melt the rough surfaces into glossy surfaces.
you can just put it in hot water and then paint it
Ryan G sandpaper make scratches which promotes adhesion
Will the paint rub off?
IF it's been prepared properly and the right paint was used then no it should not.
@@TheGeekZone Thank you. Very detailed video, Keep it up
Thats the same color as my switch Joy cons! Neon yellow
I love the neon joy cons. That's what I got with my switch.
dude i painted my ps4 controller like you did ..but when i touch it with a little bit of pressure ..i leave stamps on it ...what do i do
It sounds like the paint did not dry properly or too much was applied. I'd sand it back again and use more rubbing alcohol to get as much off as possible. Then paint it again but really lightly just enough to cover the surface. Let it dry for like 24 hours and then do the same thing again. Depending on your climate, if it's quite cold you'll need to wait longer in between coats and even maybe just have some warm air blowing on it from a good distance.
thanks i'l try again
worked this time?
Well done ,nice work man.i have a Question ,can you write me a code colour (is awesome) btw sorry for my english
The colour I used doesn't have a code. It's called Enigma Green I think.
ok,man thank you,i sub you
Welcome to the channel bro
awesome vid