That's was some great driving in that wet grass! That raises up like Godzilla roaring! I love it. You may want to get some mud gards though for future runs like that. Keep the grass from being as horrible to mess with. Great Job!
Thank you for that! You are correct mud guards may be best for this use. But it won't be staying off-road 😉 but I may invest in the stone guards only for off-road use. Certainly a good idea
I bought the XLX to 800 KV combo for my Kraton 8S. Did I fuck up should I have gotten the 1100 I don’t want my truck to top out at 55 after having just dropped another $465 plus an upgraded servo just so that I could do a couple miles an hour faster than the whack a spectrum motor that was already in it. No I took that 8S spectrum motor and 160 amp ESC and I put it in my in fraction GT it runs great armor should’ve put the ETA system in the in fraction to begin with however Kraton was under powered always with that motor so I purchased this new combo and it’s been on my workbench I haven’t even open the boxes. I’m feeling like after watching a couple videos of people only reaching 55 and 60 miles an hour with the axle Alex to 800 KV combo it has me worried but then I see you running the 1100 KV and it is ripping
Your more than fine! I actually prefer the 800 over 1100lv in my K8s. Just gear it up a little higher to compensate the speed loss. The 800 can take a lot more gear!
No sir I haven't had any issues. It's a strange thing going on with them. I bought my second xlx2 from my hobby shop. On the same shelf as 10 of them were there. One if my buddies had one go in smoke. But mine never choked. Ran it in the Kraton over 100 Mph 3 times and no issue
EPIC Brandon. 💪 👊 I run the same PL badlands MX43 on my Kraton 8s. The stock Dboots Copperhead rims are too unstable with the Big 1/5th scale electronics in mine , they turn into pizza cutters half throttle. The PL badlands Wheels are heavy, but worth the trade with heavier rubber Compound there's less ballooning for bashing
@@toysforboysrc Much more stable.... Minimal ballooning. They are VERY heavy though so if your sending it & bashing hard you might more breakages, arms etc..... But they are 1million % better than the stock D-boots.
@@toysforboysrc Much more stable.... Minimal ballooning. They are VERY heavy though so if your sending it & bashing hard you might more breakages, arms etc..... But they are 1million % better than the stock D-boots.
Yeah but it held up. Motors can run 200 degrees but they lose efficiency at that temperature. Starts to hurt the magnets inside. So I discontinued use for that day. Lastest long enough!
Yo! What size gears are you running? I'm going to do the same setup on my 8s outcast. That's awesome! PS: what do you think about a leopard 5898 1100kv motor vs the mamba 1100? Thanks, man!!!
Looks like he’s got the stock 47T spur and a 40T pinion…On the outcast you can run 1:1 gearing and not worry about a thing, I hear.. It’s lighter 1/8 not 1/5 and it’s a shorter wheelbase.
What gears younrun on that thing? Have an x maxx with the xlx2 and 800kv motor. Curious to what you run. Haven't yet run it as I haven't decided on the gearing yet
Man as soon as I heard you were running in the wet Florida glass (which seems to always be freshly cut down here) I knew it was gonna be messy 😅👍🏼 But Damn worth it’s, Awesome run bro!
Thanks, I didn't exactly intend to run this setup for off-road but I wanted to see what temperatures would be like at the end of a session. I also need a better place to run on grass. Way too tall, inconsistent, and wet over here.
@@KiloWattRC I ultimately wanted to push the xlx2 but that massive motor would give before it does. I haven't been able to breach 140 degrees yet in the xlx2
I am getting that system and have a kraton 8s I am running 1to1 gearing 39 / 39 mmx8s 800kv combo. So I feel that if you don't want to admit what gearing you are running don't mention the gearing at all. You make great vids and I watch them all the time but I am disappointed you did not add the gearing that you are using
Let's see the logs😂🙆🏽♂️. Running 400amps for 10 minutes😂😂😂🙆🏽♂️. A geardown and a motorfan would probably be more controllable= higher speed, or maybe it doesn't matter since the tires balloon so much🙆🏽♂️😂. Never seen badlands balloon like that!😂🙆🏽♂️🧨🍾. Great job!
Of course! Yeah if I were to be always running off-road, I wouldn't have pushed the 100 mph setup in it in this video. But, why the heck not lol it ran for a solid 15 min as is
No you are wrong if you understand wiring. The esc is capable of only 8s. If I ran 16 it wouldn't arm or blow up. Two sets of Parallel 4s doubles mah, combined in series one time. Double voltage once. Thus 8s 12,000mah. Just more runtime
Beast mode!!!
First time I've seen badlands balloon like that!!!
Keep the great content coming!!!!
Incredible esc it didn't even get that hot after those powerful passes, and weight of that vehicle. Definitely worth every penny.
Question what gearing would you suggest same setup, i want top speed no more than 70mph. I looking to complete my build up? Thank you so much.
Awesome run on the grass, impressive !
Appreciate that man 💪
Hey Mr innovation i have a Kraton 8s Exb with a XLX2 and 800Kv what do i need to the set up to get to around 65 to 70 mph????
Hey! I'd run 39/39 gearing on 8s that should get you 70-80 mph!
That's was some great driving in that wet grass! That raises up like Godzilla roaring! I love it. You may want to get some mud gards though for future runs like that. Keep the grass from being as horrible to mess with. Great Job!
Thank you for that! You are correct mud guards may be best for this use. But it won't be staying off-road 😉 but I may invest in the stone guards only for off-road use. Certainly a good idea
I have an outcast with the same setup how can I get mine to go that fast. Also do you recommend getting a fan on the motor
I bought the XLX to 800 KV combo for my Kraton 8S. Did I fuck up should I have gotten the 1100 I don’t want my truck to top out at 55 after having just dropped another $465 plus an upgraded servo just so that I could do a couple miles an hour faster than the whack a spectrum motor that was already in it. No I took that 8S spectrum motor and 160 amp ESC and I put it in my in fraction GT it runs great armor should’ve put the ETA system in the in fraction to begin with however Kraton was under powered always with that motor so I purchased this new combo and it’s been on my workbench I haven’t even open the boxes. I’m feeling like after watching a couple videos of people only reaching 55 and 60 miles an hour with the axle Alex to 800 KV combo it has me worried but then I see you running the 1100 KV and it is ripping
Your more than fine! I actually prefer the 800 over 1100lv in my K8s. Just gear it up a little higher to compensate the speed loss. The 800 can take a lot more gear!
@@InnovationRC Thank you I have some really nice typhoon fans to put on it to help with heat
Amazing!!
Can you share a link to your thermometer ?
BTW what pinion/spur did you have in the video?
I bought it at my local harbor freight for like 10 bucks
Very nice onboard footage!! 👍
Appreciate that! I want to get more for sure!
@@InnovationRC awesome! It’ll make for great content!!
What gear you use to get speed
That things just an absolute beast, I can see why it puts a smile on your face 😀😎😎
Yessir! I love my Kraton to no end!
@@InnovationRC I can see why 😎😀
bro that thing hitting 66mph on grass is bananas and giving 80mph on the road is insane. Great vid bro 💯💯💪💪👊
Thanks man! We gotta do a big car race at the park one day. I'm going to round some guys up with juggernaut size cars...
@@InnovationRC let's do it bro. you got my number just call me or text me. I'm down for that
@@heat305rc I got you man
i see he want tell you the gear setting/// he keep saying overdrive
Sweet!! Keep em coming!
Thanks Chris!
Good stuff bro. That really shows what strain that XLX2 can take! Pretty incredible.👍🏼 I need one...or two.😀
Thanks man still testing this esc and still failing to strain it!
nice 1 !! What spur /pinion size pls? Is the motor comparable with the hobbywing 1100kv (from the max6 combo)?
I'd say this motor will have more torque than the hobbywing 1100kv. I am running overdrive gears. NOT recommended whatsoever for off-road use
This is the exact set up I what on my exb
New lawn mower is looking fresh 😁😁😁🤷♀️🤷♀️🔧🔧🔧🔧
Lol thanks man my John Deere is hauling!
Have you had any problems with the xlx2 catching on fire? Alot of people seem to be having problems with it bursting into flames
No sir I haven't had any issues. It's a strange thing going on with them. I bought my second xlx2 from my hobby shop. On the same shelf as 10 of them were there. One if my buddies had one go in smoke. But mine never choked. Ran it in the Kraton over 100 Mph 3 times and no issue
@@InnovationRC I just hope it doesn't burn my truck down. Its gonna be used for bashing on a basically stock xmaxx except for motor and esc.
Absolutely awesome bad ass speeds Running video bro, CRAZY SPEEDS 😜 can't believe the heat off that motor 🔥really enjoyed this Video bro 👍😎😍👍
Thank you sir! Glad you enjoyed it
Crazy 😱 200 degrees. Guess that's not a bashing set up 😜
You are correct I wouldn't never bash with this setup way too high of a gearing
@@InnovationRC still really impressive! 👍👍
A couple of "Game Changer" fans on the motor would keep your motor happy I'm thinkin. I love that truck bro!
Yessir. I have NTF which is what I need to install
What gearing?
Looks like a Mojave level of grass in that bad boy
Yeah it was kinda tall and not even enough for higher speeds
Great video
Thank you sir!
@@InnovationRC no problem keep innovating
Did you upgrade the motor mounts
EPIC Brandon. 💪 👊 I run the same PL badlands MX43 on my Kraton 8s.
The stock Dboots Copperhead rims are too unstable with the Big 1/5th scale electronics in mine , they turn into pizza cutters half throttle. The PL badlands Wheels are heavy, but worth the trade with heavier rubber Compound there's less ballooning for bashing
how differently does the truck perform and feel with those mounted tires?
@@toysforboysrc Much more stable.... Minimal ballooning.
They are VERY heavy though so if your sending it & bashing hard you might more breakages, arms etc..... But they are 1million % better than the stock D-boots.
@@toysforboysrc Much more stable.... Minimal ballooning.
They are VERY heavy though so if your sending it & bashing hard you might more breakages, arms etc..... But they are 1million % better than the stock D-boots.
IS THAT STILL 70C OR DOES IT BECOME 140C ??….bcs WERE ACTUALLY 12000mah now so does the C rating go up too?
Prob have much different results in dry grass ...?
Yes most likely. Short dry grass would be best. Plus they just trimmed the grass so it all got stuck inside the vehicle
That's one hell of a lawn mower you got there! What gearing are you running?
Lol thanks man, gearing is in overdrive. Not exactly recommended with this motor and size vehicle
@@InnovationRC is it the same at the road speed runs you did on it?
Nice rips that thing is fast
Thanks Kurt!
Pinion ?
I’m surprised the motor didn’t spontaneously combust with those temps🔥😆!
Yeah but it held up. Motors can run 200 degrees but they lose efficiency at that temperature. Starts to hurt the magnets inside. So I discontinued use for that day. Lastest long enough!
Yo! What size gears are you running? I'm going to do the same setup on my 8s outcast. That's awesome! PS: what do you think about a leopard 5898 1100kv motor vs the mamba 1100? Thanks, man!!!
Looks like he’s got the stock 47T spur and a 40T pinion…On the outcast you can run 1:1 gearing and not worry about a thing, I hear.. It’s lighter 1/8 not 1/5 and it’s a shorter wheelbase.
Gonna need the 800kv motor
Hit 90 on the badlands in my xmaxx with the xlx2 1100. Beast
What gears younrun on that thing? Have an x maxx with the xlx2 and 800kv motor. Curious to what you run. Haven't yet run it as I haven't decided on the gearing yet
@@kris1black1 1100kv 40/30
Great run just ran my 8s on the Florida grass and boy its almost unusable
Yeah you need very thin and short grass to get some serious runs in
Man as soon as I heard you were running in the wet Florida glass (which seems to always be freshly cut down here) I knew it was gonna be messy 😅👍🏼 But Damn worth it’s, Awesome run bro!
Lol you already know! Appreciate it for sure man. It's been raining too often so I can't hit the road with foam tires... Had to bring the badlands out
I need that 1100kv motor 😩
How do u do the jumps
It's just popping wheelies from the inconsistency of the grass. That's why I went onroad to see if the same result would occur. And it didn't 😉
Gear it down some, that will avoid wheelies at high speed. Cool video man
Thanks, I didn't exactly intend to run this setup for off-road but I wanted to see what temperatures would be like at the end of a session.
I also need a better place to run on grass. Way too tall, inconsistent, and wet over here.
@@InnovationRC that was pretty raDD with the motor lead un soldering from motor
@@KiloWattRC I ultimately wanted to push the xlx2 but that massive motor would give before it does. I haven't been able to breach 140 degrees yet in the xlx2
Sick
Thanks Garrett
Whats the gearing
Very very tall. Overdrive
I would like to know as well and that answer is not a real reply to the question.
I am getting that system and have a kraton 8s I am running 1to1 gearing 39 / 39 mmx8s 800kv combo. So I feel that if you don't want to admit what gearing you are running don't mention the gearing at all. You make great vids and I watch them all the time but I am disappointed you did not add the gearing that you are using
Let's see the logs😂🙆🏽♂️. Running 400amps for 10 minutes😂😂😂🙆🏽♂️. A geardown and a motorfan would probably be more controllable= higher speed, or maybe it doesn't matter since the tires balloon so much🙆🏽♂️😂. Never seen badlands balloon like that!😂🙆🏽♂️🧨🍾. Great job!
Of course! Yeah if I were to be always running off-road, I wouldn't have pushed the 100 mph setup in it in this video. But, why the heck not lol it ran for a solid 15 min as is
isnt that a 16s setup? look like you have 4 , 4s batteries
No you are wrong if you understand wiring. The esc is capable of only 8s. If I ran 16 it wouldn't arm or blow up.
Two sets of Parallel 4s doubles mah, combined in series one time. Double voltage once. Thus 8s 12,000mah. Just more runtime
Sorry.. can i ask where r the front springs?..
With the speed setup installed I took them out to lower the front end
@@InnovationRC ohh.. got u.. 👍
All good, if I were to normally run off-road I'd keep the springs on. Obviously lol
Fan on motor too and do it again
Next time it'll have an ntf setup on it. Should certainly be cooler, longer
All that grass can't be good for it probably why it died Dang what a beast though bro 🔥👍✌️
Never died, It could've kept going but I didn't want to run anymore over 200 degrees. Performed amazing though!
@@InnovationRC Oh my bad I thought you said the motor cut out Yeah that thing is awesome ✌️
Ayy another vid been waiting for this
Glad you like it! Have awesome stuff planned. Just need time to finish the builds
@@InnovationRC ooooo 👀can’t wait bro
I thought I was watching crisfix for a minute 🤣
Close 😉 I enjoy his videos
Worlds fastest lawn mower
Your not wrong
Nothing like wet florida grass🤣
YuCk! It's so swamp like. Kraton just hydroplaned over it like it was nothing though haha
Bruh you should take this on a jump it’s a kraton 8s it’s still a off-road car so you should jump it oh wait I know 30k special jumping kraton 8s
I don't exactly have anywhere to jump but that's be awesome! I have something planned for 30k too
@@InnovationRC ok but I wonder what planned for 30k I’ll definetly be here for it you bet keep up the good work