Changed G35 Valve Covers and now my IDLE is LOWER than my GPA

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 ต.ค. 2024

ความคิดเห็น • 68

  • @rudolphn84
    @rudolphn84 4 ปีที่แล้ว +26

    You took off the throttle body. By you unplugging that you have to get it reset. Nobody mentions that in they videos. But great job. I like you adding all these mods. I hate the g's are expensive to get more horses.

    • @BeDistinct
      @BeDistinct  4 ปีที่แล้ว +2

      Rudolph Navarro that’s true, I definitely should of mentioned that. Thanks for pointing it out.

    • @societyplays9943
      @societyplays9943 4 ปีที่แล้ว

      I agree your not suppose to take it off . Take it off complete with the upper . Unless you wanna waste your time doing a reset

    • @crunkjuice29
      @crunkjuice29 4 ปีที่แล้ว +3

      You can take off the throttle body and put it back on and it will be fine. What messes up the idle is if you even slightly touch the butterfly valve is fucked and have to do the relearn.

    • @locomojo0485
      @locomojo0485 4 ปีที่แล้ว +7

      @@societyplays9943 If you disconnect the battery first, before you unoplug anything. And don't fingerfuck the butterfly valve in throttle body then you don't have to waste your time relearning anything.

    • @Kyle_gallegher
      @Kyle_gallegher 3 ปีที่แล้ว +1

      @@locomojo0485 i agree ppl.take off the whole harness sometimes and all you do is unplug the battery everything will be fine unless u have mismatched vin crap on ur G your g2g lol

  • @BeDistinct
    @BeDistinct  4 ปีที่แล้ว +7

    PT.2 of Fixing the G will come probably tomorrow!

    • @vladsgarage2623
      @vladsgarage2623 4 ปีที่แล้ว +2

      BeDistinct you have to do the idle reset since you unplugged the throttle body

    • @lilgoon8613
      @lilgoon8613 3 ปีที่แล้ว +1

      Aye can you link the part 2 and why it was idling so low?

  • @macee1491
    @macee1491 4 ปีที่แล้ว +3

    Theres are lot of error in your installation. You dont need to apply the silicone gasket, you can only apply a thin coat on the corner of half moon as long as you torque the bolt in proper spec. The aftermarket valve cover is garbage, the main problem is the sparkplug seal , the oil will leak due to poor quality of seal. You need to reset the ECU by performing the throttle relearn procedure or using the Consult II of Nissan Dealership.

  • @DOMS4.
    @DOMS4. 4 ปีที่แล้ว +7

    Its either vacuum leak or a throttle relearn.

  • @jamesalbright6155
    @jamesalbright6155 4 ปีที่แล้ว +2

    I was guna seal the gasket on too but then i did some logical thinking and talked to a master tech , the sealer will litterally casue a leak 😲😢😤 only dab the timing cracks

    • @Kyle_gallegher
      @Kyle_gallegher 3 ปีที่แล้ว

      I was gonna say nice job but then I saw how he used too much and not just in the cracks. Oh well this is how u learn lol

  • @jdmislife5372
    @jdmislife5372 4 ปีที่แล้ว

    I had the same issue, u gotta get the tb reset take it to a shop or google the step but honestly I’d just pay to not have a pain to do it .

  • @richardbean5549
    @richardbean5549 4 ปีที่แล้ว +1

    Best g35 youtuber right here

  • @luisorozco8301
    @luisorozco8301 4 ปีที่แล้ว

    Look up the throttle reset function. You play with the gas pedal and the ignition and it resets your idle and throttle response.

    • @killerkennyas
      @killerkennyas 7 หลายเดือนก่อน

      Would it say multiple misfires?,p0300 and p0011?

  • @itz_ur_boy_kevin6597
    @itz_ur_boy_kevin6597 4 ปีที่แล้ว

    I have the same problem. But I left the throttle connected to the plenum. Got the p0300. Replaced all ignition coils. Replaced to oem spark plugs. Still same problem.

    • @lenermaz4546
      @lenermaz4546 2 ปีที่แล้ว

      Ever get this fix I'm getting p0300 code now did everything you replaced anything as well helps.

    • @killerkennyas
      @killerkennyas 7 หลายเดือนก่อน

      ​@lenermaz4546 ughh
      .me to..what was the issue?

  • @hydemary3040
    @hydemary3040 4 ปีที่แล้ว +1

    do you have stock rear taillights? if so do you plan on getting aftermarket ones? and what ones are the best quality on the market rn?

  • @lment420
    @lment420 4 ปีที่แล้ว +1

    I have the same problem thinking it could be the camshaft sensor my g just died on me yesterday but turns right back on after turning it off

  • @deesorb9323
    @deesorb9323 4 ปีที่แล้ว +2

    Where did u get the valver covers ??I need some for my G

  • @Jmoneysparkz
    @Jmoneysparkz 4 ปีที่แล้ว +1

    Can you please put the link to the valve covers

  • @SilverSurfer299
    @SilverSurfer299 4 ปีที่แล้ว +2

    Idle relearn?

  • @jamesalbright6155
    @jamesalbright6155 4 ปีที่แล้ว +1

    Bro did u gap the spark plugs? Or use right ones? , i assume u did those sense u were right there

  • @djgblaze1of1
    @djgblaze1of1 3 ปีที่แล้ว +1

    Were you order you valve covers ?

  • @jesehernandez3071
    @jesehernandez3071 3 ปีที่แล้ว

    Heyyy!!!! I have a question...Idk if you have time to answer it.. but I have an auto 06 G35X sedan, and both valve cover gaskets are leaking, you think I could just replace the gaskets? or should I replace the valve covers too🤔

    • @mels_life1
      @mels_life1 3 ปีที่แล้ว

      Change it all, might as well since you’re down there

  • @alanserrano2411
    @alanserrano2411 4 ปีที่แล้ว +1

    Disconnect your battery for 30min and connect and try again, I think you touched the butterfly on the throttle body

  • @DGWhipZ
    @DGWhipZ 4 ปีที่แล้ว +4

    You might need to do a throttle body relearn if you took the whole throttle body off the plenum

    • @BeDistinct
      @BeDistinct  4 ปีที่แล้ว

      DGWhipZ that’s what I’m thinking

  • @Kyle_gallegher
    @Kyle_gallegher 3 ปีที่แล้ว

    What valve cover brand is it, for oem cheapest I can find is 425 dollars

    • @BeDistinct
      @BeDistinct  3 ปีที่แล้ว +1

      It’s called MostPlus from Amazon and I replaced that gasket with a FeltPro from autozone

    • @Kyle_gallegher
      @Kyle_gallegher 3 ปีที่แล้ว

      @@BeDistinct nice bro ty for the sauce. How many miles with this cover? Still solid? Sorry if im buggin

  • @iiiSaav
    @iiiSaav 4 ปีที่แล้ว

    Let’s get to 10K already man!!

  • @goodnightvids
    @goodnightvids 2 ปีที่แล้ว

    The green flip flop lmao

  • @phase0ne
    @phase0ne 3 ปีที่แล้ว

    hey bro how much does this cost to get replaced?

  • @beenactive4642
    @beenactive4642 4 ปีที่แล้ว

    That’s crazy I just did that today and have the same problem did you find what it was I ain’t trying to pay no mechanic LMK please 😂

  • @nineeighteenmedia6852
    @nineeighteenmedia6852 3 ปีที่แล้ว

    How is the value covers gasket holding up any leaks?

    • @BeDistinct
      @BeDistinct  3 ปีที่แล้ว

      Sold the car since then but it held good last time I had it, no leaks.

    • @nineeighteenmedia6852
      @nineeighteenmedia6852 3 ปีที่แล้ว

      @@BeDistinct ok cool I got a 04 in the garage ready for the gasket. I was wondering if so should put the Gasket maker all the way around the block like you did.

  • @NjBoriG35
    @NjBoriG35 4 ปีที่แล้ว

    I just did this on my car. Now they leaking again.. got to do it 2x.

  • @jamesalbright6155
    @jamesalbright6155 4 ปีที่แล้ว

    Yo how are your most plus valve covers holding up ? any leaking ?

    • @BeDistinct
      @BeDistinct  4 ปีที่แล้ว +1

      Still holding up good my friend 👌🏽

  • @mahdigrant8158
    @mahdigrant8158 4 ปีที่แล้ว +1

    Love the video❤️

  • @luigui707
    @luigui707 3 ปีที่แล้ว

    What was the hose called that you replaced?

  • @martinv3126
    @martinv3126 4 ปีที่แล้ว

    Idle relearn bro. That should most likely fix the issue.

  • @miguelsanchezzz_
    @miguelsanchezzz_ 4 ปีที่แล้ว +1

    Love the car man but please don’t tell me you’re mommy and daddy sponsored lol

    • @BeDistinct
      @BeDistinct  4 ปีที่แล้ว

      Chivas Sanchez I wish, I wouldn’t have bought a G35 if I was

  • @truettcash8555
    @truettcash8555 3 ปีที่แล้ว

    What valve cover gasket did you put in?

    • @mrau92me
      @mrau92me 3 ปีที่แล้ว

      For our G35, we bought Victor-Reinz (Dana) vc gaskets, and I did not even have to put gasket maker to get it to stay in the VCs. I'm quite positive Victor-Reinz was the oem gasket supplier for these engines. I used to be an engineer for Fel-pro and we used to quote annually to supply gaskets to Nissan and the drawings they would send us to quote by always had the Dana logo barely blacked out. They never gave us any of their business, so I'm quite sure it stayed with V-R.

  • @Hbk_adam
    @Hbk_adam 4 ปีที่แล้ว

    Why don’t u do a throttle body relearn

  • @mrrr407
    @mrrr407 3 ปีที่แล้ว

    Lmfaoo that title tho

  • @Boosted_Martin
    @Boosted_Martin 4 ปีที่แล้ว +1

    I want that trunk 🤔

    • @BeDistinct
      @BeDistinct  4 ปีที่แล้ว +1

      Hmmm 🧐 giveaway? 😂

  • @1slowmach1
    @1slowmach1 4 ปีที่แล้ว

    Dam ur gaskets are all fucked up in the package 😂😂 they gave no fucks.

  • @Mjm635876
    @Mjm635876 4 ปีที่แล้ว

    where did you get the valve covers

    • @BeDistinct
      @BeDistinct  4 ปีที่แล้ว

      Mjm635876 they are called Most Plus G35 Valve Covers on Amazon, let me add it to the description.

    • @treatpeopleright5483
      @treatpeopleright5483 4 ปีที่แล้ว

      Hey there BeDistinct. How are your valve covers holding up? I seriously need some, due to my screw from coil pack 1 breaking inside while changing my spark plugs. Peace from Baltimore, MD.

  • @jamesjames2764
    @jamesjames2764 4 ปีที่แล้ว

    AYEEEEE SUPPPP FUKERSSSS

  • @Tewthpaste
    @Tewthpaste 4 ปีที่แล้ว

    *time to trade it in for a faster car.*

    • @BeDistinct
      @BeDistinct  4 ปีที่แล้ว +1

      Tewthpaste ima keep it but I am looking into a car already

  • @hardbody3518
    @hardbody3518 4 ปีที่แล้ว

    I was the 100 like let’s goooo