Never dealt with these style carbs before and have an old Mikuni that's just like this, rusty carb broke the cable trying to take it off need to replace so really helpful for me thanks a ton
Does the pin sit in the slider really loosely? I have another tiny little clip thing it’s like a u shape? Not sure where it goes, on the inside of the black slider thing or on the outside where the pin sticks out!?
I’m new to motorcycle repair so bare with me, I bought two carbs ready to go for my build but can’t figure out how to remove the inside round slide with the needle so I can install the throttle cables
Can you tell me where I can find a throttle cable with the proper crimped end to fit into the round disc? I have found a lot on line but the crimped on barrel is sideways compared to what I need and what you have in the video. Replacing a broken cable.
I'm working on a OLD Honda c102 and I can't get the throttle cable unhooked from the carburetor. Should it just slide out once the cap is unscrewed, or is there a screw I'm overlooking the would be holding all of it in?
I installed perfectly ,but when I pull the throttle handle, it doesn't return back. The spring is correct. I even filed down some plastic inside the lever on the kill switch.??? Can someone help me???
Ordered my carburetor last week, and it didn’t come with a Pac-Man clip. The needle came with a c clip. Could this be the reason why my idle runs high for a bit then drop down after I hit the throttle?
My bike won’t fire up putting bbr tall bars on my pit bike and I had to put a new cable on it and she don’t wanna fire up sounds like it is not getting gas
I did this to put a new throttle cable and when I turn on my quad and it revs up super high and I don’t know how to fix and yes I did get the right size can sum one help me out pls
Probably not, vacuum draws the gas into the carburetor as the needle (gas) and slide (air) are raised by the throttle cable. Gas entering the carburetor by gravity is usually indicative of of a stuck or defective float or float needle. That's how the "tickler" primer works, it temporarily lifts the float in a position that allows the float needle to slightly flood the carburetor with raw gas for initializing a cold start. Whereas the choke creates more vacuum to maintain a rich mixture for the duration of the warm-up period.
The most intense tutorial I've ever seen. Straight to the point and simple. Thank you.
I was almost there, missed the lining up of the slot on the plunger. You saved me ages of messing around. Thankyou
very straight forward, and helpful, that is the kind of video I want to watch. Thank you!
ये wire लगाने से क्या फायदा होता है
Finally a video that actually gives me the information I'm looking for.
Thank you so very much. Would not have been able to assemble my first motor with out your help. :)
your channel just got subscribed
Never dealt with these style carbs before and have an old Mikuni that's just like this, rusty carb broke the cable trying to take it off need to replace so really helpful for me thanks a ton
Thank you, straight to the point, crystal clear, the kind of video I'd like to see more often.
Your video was so much help because we did not know that the pieces had to lineed up and your video was the one to help so thanks so much.
Golly, thank you so much! With the help of your video I was able to install my first carb.
you guys just saved me from more our of work on my 89 lt230 thanks so much
thank you! chinese instructions are notoriously hard to follow
Now this is helpful
Love the video! So simple! Thank you!
helpful and straight forward, cheers.
once I've put it together, it won't allow the bike to go and just stays at a speed
ROGHT
Thank you for posting
simple and straight to the point thanks a bunch
Thank you for this video, you helped me figure out what i did wrong :D
Does the pin sit in the slider really loosely? I have another tiny little clip thing it’s like a u shape? Not sure where it goes, on the inside of the black slider thing or on the outside where the pin sticks out!?
So question what do I do if there isn't a spring on the inside? How do I replace that spring?
No bs straight to the point
I’m new to motorcycle repair so bare with me, I bought two carbs ready to go for my build but can’t figure out how to remove the inside round slide with the needle so I can install the throttle cables
Is the pacman clip needed?
How do I get the cap to stay on the carburetor that holds the throttle cable it keeps popping off?
Can you tell me where I can find a throttle cable with the proper crimped end to fit into the round disc? I have found a lot on line but the crimped on barrel is sideways compared to what I need and what you have in the video. Replacing a broken cable.
Malfunctioning of this pin can cause high acceleration?? Uncontrollable??
Nice ..Mikuni vid would be nice as well
very helpful. thank you. have a good 2018
PerFecT bro 👍
I'm working on a OLD Honda c102 and I can't get the throttle cable unhooked from the carburetor. Should it just slide out once the cap is unscrewed, or is there a screw I'm overlooking the would be holding all of it in?
I installed perfectly ,but when I pull the throttle handle, it doesn't return back. The spring is correct. I even filed down some plastic inside the lever on the kill switch.??? Can someone help me???
Ordered my carburetor last week, and it didn’t come with a Pac-Man clip. The needle came with a c clip. Could this be the reason why my idle runs high for a bit then drop down after I hit the throttle?
When I pull the throttle, I don’t accelerate and the motor doesn’t rev . What is the problem so I can fix it
My bike won’t fire up putting bbr tall bars on my pit bike and I had to put a new cable on it and she don’t wanna fire up sounds like it is not getting gas
yes very helpful Thank You!
I did this to put a new throttle cable and when I turn on my quad and it revs up super high and I don’t know how to fix and yes I did get the right size can sum one help me out pls
where can i buy high temperature red clutch friction pads
dude you fkn Rock...thanks
Very helpful
Very nice, thank you.
Nice one 😁😁😁
wat size cable do i need for 125 pit bike
so I need to know something if I'm leaking gas while the throttle is down that means I need to lower the pain right
Probably not, vacuum draws the gas into the carburetor as the needle (gas) and slide (air) are raised by the throttle cable. Gas entering the carburetor by gravity is usually indicative of of a stuck or defective float or float needle. That's how the "tickler" primer works, it temporarily lifts the float in a position that allows the float needle to slightly flood the carburetor with raw gas for initializing a cold start. Whereas the choke creates more vacuum to maintain a rich mixture for the duration of the warm-up period.
Where can I get the spring?
Where can I buy the Pacman clip and the needle I do t want to buy a new carb
Cable won't go all the way inside
1 inch left outside
What's problem ?
Yo thanks so much
Thank you, well made
Bajaj Platina ki accelerator wire double kyu Hoti Hai kripya ek video Banaye
Agar wire Ka agay Kuch na hi to Kia lagaiye
What the name of that throttle cable
legend. thank you
where to get ur channel logo on shirt please
Mine would stay straight it goes to one side
very well 🌿🌿🌿🌿👌👌👌👌
Niceeelyyy
👍👍
you very very good
WHERE CAN I FIND THIS PACMAN CLIP
You ever find it?
Jhakaas
Thanks bro
I want TVs we go acceletre carboter pistin
were can i get a pack man clip
did you find the somewhere to buy the Pac man clips?
No but it still works good but most likely online I made mine if u have a little washer and some nail clippers it will work
Andy Holden I just looked online and couldn't find em online u might have to make one let me know if u have anymore questions
Thanks will have a go tonight.
I can’t find the PacMan clip
“KC fitted run bout 150”
Mine is stuck and I cant get it out
Daumantas Mikalauskas ur slide is stuck so is mine it came apart about a week before I tried fixing it and now is almost like it's welded to the carb
302 diamond state actualy it magicly fell out
Good 'but with Voice it would be More better
Thanks
I got swap the sprin
Please video carburator pz 30
that end is easy other end on an ATV???
Tvs xl100 same video
I lost my pac man ring, can I go without it?
no
Way to get right to it
Muzyczka do szału doprowadza
Thanks bro
Thanks
Thanks
Thankyou