I had two leaking TM G17 valves from the base and after applying some lube to the square O ring it is once again gas tight. This video was a great help - thanks!
hey knuckles i have some G17 Mags from TM my problem is: i got the feeling they are way too early full (with gas) takes just 3 seconds and they are already full (gas is streaming every after the 3 seconds) and i cant even shoot all BBs in the mag. a friend reccomended me to put an o-ring from a lighter into the filling valve and to put the gas bottle 30 seconds on it... do you have some tips?
there are a lot of factors that are missing here and hard to diagnose something like this, for example: whats the temperature? whats the build? anything custom? is your gas empty and its just air left in it etc. i dont have any problems with my tm magazines and never needed the o-rings to fix them so you must be doing something wrong but not sure what it is
Those O-rings at @3:40 can be sealed up using black gasket sealant. I made a video on my channel about this. I had a major problem with CO2 in my KP05 that I fixed with black gasket sealant.
Stock power valve is good enough, if you are looking to increase gas efficiency, you would go for the aluminum bbu and short stroke the glock and try to keep the plastic slide for as long as you can. Those alone will help increase the gas efficiency, there is more you can do but those are more for increasing the fps or making the gas flow better.
Can a TM G17 magazine fit a KJW 23/32c? I know its 17 vs 19, but using an X Grip will this work better? I am debating on ordering a G19 from WE or KJW 23/32c. I like the WE's grip. I know they have have a bad rap but I seen several good reports from guys locally at my field and online. I think it was the 18c that had the bad rap?.
They are really not bad for the price tag thats for sure. They tend to leak a bit faster than TM but super easy to fix and the followers will break after a bit, but still works perfectly fine. Weigh less than the TM a bit as well. Hope that helps! :)
Hey i want to know if the nineball rubber work on we g17 mag. In the video you tell that you can upgrade it, but i want to know if i can use it on my g17 we
i run both for different reasons, we is cheap and easy to fix, weighs less and I use tm when im lazy and don't want to maintain my mags as much as the WE ones, weighs a bit heavier too
I heard that if your gasket starts to leak you should take it out and put Form a Gasket type 1B on it and seal it back up and that'll solve your leaking problems. Do you recommend that or just lubing the o ring/gasket?
@@KnucklesGSM for TM glock17, look i wanna know if this valve works on the magazine: www.shootercbgear.com/product_info.php?products_id=9502&osCsid=j43nadbr08l0mfqjq1sbg20m62
i am not sure where you are based but i wouldn't grab that as there are inlet valves designed specifically for marui and will have it in the listings, problem is finding the ones in stock if anything. www.shootercbgear.com/product_info.php?cPath=28_88&products_id=12066&osCsid=j43nadbr08l0mfqjq1sbg20m62 www.shootercbgear.com/product_info.php?cPath=28_88&products_id=15657&osCsid=j43nadbr08l0mfqjq1sbg20m62
If I were to replace the magazine follower, can I just get away with removing the feed lip at the top of the magazine or do I have to remove the base cap? Thanks.
hey knuckles i have recently decided to get some upgrades and everything works fine accept my mag, i am still having feeding issues after i have upgraded to one of the purple shooters design mag lip, its seems to be getting caught just as the bb enters the mag lip and wont feed up. Any sugguestion on what i should do? i took a really close look and it seems like the mag bevels the bb before it enters the lip which is causing it to snag on so should i file down the mag or trim the mag lip?
+Jordan Monaco see if you can trim one but be very careful, i learned the hard way with trimming stuff, you can never truly add material back so do it very little at a time and test each time
Nineballs are pretty dope but just watch out, they are funky with with loading nozzles. Some they like and some they don't, so if you got friend who has one, try it out or just buy 1 set.
Thanks again for the help! And i was wondering that if I was get a tight bore barrel and a low power valve(if they make them), would it increase the gas efficiency?
I mean, anything "specific" worth noting. I'm sure they'll hold a gas and whatnot cause I can test that at least but I can't tear one apart to really get a good look.
I had two leaking TM G17 valves from the base and after applying some lube to the square O ring it is once again gas tight. This video was a great help - thanks!
AnkleSpankle Airsoft np bud!
"always really tight, especially the first time"
>_
hey knuckles
i have some G17 Mags from TM
my problem is: i got the feeling they are way too early full (with gas)
takes just 3 seconds and they are already full (gas is streaming every after the 3 seconds) and i cant even shoot all BBs in the mag.
a friend reccomended me to put an o-ring from a lighter into the filling valve and to put the gas bottle 30 seconds on it...
do you have some tips?
there are a lot of factors that are missing here and hard to diagnose something like this, for example: whats the temperature? whats the build? anything custom? is your gas empty and its just air left in it etc.
i dont have any problems with my tm magazines and never needed the o-rings to fix them so you must be doing something wrong but not sure what it is
Those O-rings at @3:40 can be sealed up using black gasket sealant. I made a video on my channel about this. I had a major problem with CO2 in my KP05 that I fixed with black gasket sealant.
Its up to you, lube is fine as well as gasketing it. Its really based on how bad it is and how often you want to maintain it.
Stock power valve is good enough, if you are looking to increase gas efficiency, you would go for the aluminum bbu and short stroke the glock and try to keep the plastic slide for as long as you can. Those alone will help increase the gas efficiency, there is more you can do but those are more for increasing the fps or making the gas flow better.
It is normal that the magazine lip broke easily is it the gunsmodify a good replacement?
Can a TM G17 magazine fit a KJW 23/32c? I know its 17 vs 19, but using an X Grip will this work better? I am debating on ordering a G19 from WE or KJW 23/32c. I like the WE's grip. I know they have have a bad rap but I seen several good reports from guys locally at my field and online. I think it was the 18c that had the bad rap?.
They are really not bad for the price tag thats for sure. They tend to leak a bit faster than TM but super easy to fix and the followers will break after a bit, but still works perfectly fine. Weigh less than the TM a bit as well. Hope that helps! :)
could I use permatex dielectric grease on the valve orings????(orings that prevent leaking at the top)
Hey i want to know if the nineball rubber work on we g17 mag.
In the video you tell that you can upgrade it, but i want to know if i can use it on my g17 we
they work on tm and we mags
say does ksc 50rd glock mag or TM 50rd compatible with my kjw ?
What size is the punch to use for getting the magazine lip pin out?
Build quality yes, fps, can't answer that because too many different variances. I've stuck with WE/TM mags pretty much.
i run both for different reasons, we is cheap and easy to fix, weighs less and I use tm when im lazy and don't want to maintain my mags as much as the WE ones, weighs a bit heavier too
I heard that if your gasket starts to leak you should take it out and put Form a Gasket type 1B on it and seal it back up and that'll solve your leaking problems. Do you recommend that or just lubing the o ring/gasket?
Where did you get your AIP magazine base? Im looking for 1 for my WE magazine but theyre extremely hard to find
+gamezmeow yea they are pretty old and discontinued, gotta browse lots of oversea websites
Hi knuckles the injection valve is broken, do you know which is the diameter of that part? 5mm or 6mm?
Which mag?
@@KnucklesGSM for TM glock17, look i wanna know if this valve works on the magazine: www.shootercbgear.com/product_info.php?products_id=9502&osCsid=j43nadbr08l0mfqjq1sbg20m62
i am not sure where you are based but i wouldn't grab that as there are inlet valves designed specifically for marui and will have it in the listings, problem is finding the ones in stock if anything.
www.shootercbgear.com/product_info.php?cPath=28_88&products_id=12066&osCsid=j43nadbr08l0mfqjq1sbg20m62
www.shootercbgear.com/product_info.php?cPath=28_88&products_id=15657&osCsid=j43nadbr08l0mfqjq1sbg20m62
If I were to replace the magazine follower, can I just get away with removing the feed lip at the top of the magazine or do I have to remove the base cap? Thanks.
you can remove it from the top
Thanks, that would be easier
hey knuckles i have recently decided to get some upgrades and everything works fine accept my mag, i am still having feeding issues after i have upgraded to one of the purple shooters design mag lip, its seems to be getting caught just as the bb enters the mag lip and wont feed up. Any sugguestion on what i should do? i took a really close look and it seems like the mag bevels the bb before it enters the lip which is causing it to snag on so should i file down the mag or trim the mag lip?
+Jordan Monaco see if you can trim one but be very careful, i learned the hard way with trimming stuff, you can never truly add material back so do it very little at a time and test each time
Do you recommend Guarder or Nineball gaskets for G17 Magazines? (Using for a G18c)
Nineballs are pretty dope but just watch out, they are funky with with loading nozzles. Some they like and some they don't, so if you got friend who has one, try it out or just buy 1 set.
great video :) quiestion: ware did you buy the tools you use to remove the valve?? thanks have a nice day :)
aipairsoft.com! :)
Whered you get that AIP valve key?
Thanks again for the help! And i was wondering that if I was get a tight bore barrel and a low power valve(if they make them), would it increase the gas efficiency?
Whered you get that AIP valve key? thanks :)
Is their any diffrence in fps/quality between TM/WE/KJW?
Will TM mags fit in a WE G19??? Plz help.
hi, do you know if the WE and TM mags will work in the KJW glock thanks
Are the WE mags any good? I'm debating picking up some 50rds for my Glock through local means but wasn't sure of what to expect.
does the ARMY mags fit in the WE G17 Gen4, and are ARMY mags any good ?? :) Thanks
Anders Peter Jørgensen army mags work fine
KnucklesGSM Great ! :) Thanks man
They are okay at best, they do leak easier from what I've been working with and checking on but easy to fix
Do you know the size for the g mags big base plate o-ring is?
56halofan Do not know that off hand, sorry bud
What replacement fill valves work with tm mags
Can WE mags work in a TM G17? I heard they are different somehow.
Yes
Do you know where to get parts for a kjw glock mag?
check on google bud, should be able to find some stuff
Thanks for the tip! By the way, how is your we g18c holding up?
what mags do you recommend? TM or WE?
I mean, anything "specific" worth noting. I'm sure they'll hold a gas and whatnot cause I can test that at least but I can't tear one apart to really get a good look.
Very nice video! I find lots of parts for hicap in aipairsoft.com, will those pats fit in all brands hi-cap or has to be TM?
Feisi Meng it may or may not, fitment is very vague, my best advice is just be prepared to fit
Thank you so much
8K views and little to no one likes, dissapointing, good video!
proarms fill valves
Still alive lol! :)
Got it from aipairsoft (dot) (com) Hope that helps! :)
does Kwa g17 mag fit WE g17??
no