Hi, can I say right now that this a such a fantastic and useful channel, your explanations are thorough yet quick so it doesn’t take too long, this re-assembly helped me so so so much and I literally cannot thank you enough!
I cannot express thankful I am and how much you were able to save my g18 with your series of videos. I too had broken my loading nozzle which I was able to fix with some adhesive. The spring I had to straighten for close to an hour however. While watching your videos I found the issue as I had never used a WE glock before and knew very little about its inner workings. It was only a matter of time before the nozzle broke which I knew from the start, but these pistols are cheap and easy to upgrade as far as the slide goes. Evike has started to sell the nozzles again on there website under angel custom with a new polycarbonate red material. If anyone does not want to spend the money on buying a new one, you can simply take the nozzle, put adhesive glue on the broken corner and the corresponding broken piece and let them dry together, afterwards you can then layer the back of the chipped piece to reinforce it. From my knowledge this lasts over several hundred rounds until you repeat the process. I hope this helped someone as much as your videos helped me. Keep up the great work man!
Don’t quote me on this but I had same problem a punk to take slide back off. I’m sure that when u put the recoil spring back on you pushed it to high in the slide. I levelled the recoil to be straight then it was sweet as. Oh yeah should mention that grease and lube as you go. Either way thanks you bloody LEGEND!!!!
Men, you save my day. I've a G23c WE It's impossible to found a fucking explosed view of it and found how to put in this fucking mag release button! THANK YOU MAN!
Hey, I tried to rebuild my slide but when I finished when I cock it it stops about 2mm away from where it’s supposed to but if I tap it it goes back, I tried firing it but it sticks holding the green gas button and dosnt do anything but release green gas. If anyone could me understand what I did wrong it would be a huge help
FYI: Upper or slide assembly begins at 8:22 Just in case that is your only concern. Beginning of the video is all about the lower or the pistol frame. Enjoy!
The inner barrel is a 7inch 6.01 PDI, its a good length for the comp that I have on it right now! Hope that helps, and let me know when you get that video, try to show the problem as well or whatever works! :)
3:02 People, make sure your hammer assembly is cocked, when you reassemble it back to the gun, otherwise your trigger will not reset correctly after the final shot.
It sounds like your bucking overswelled (replace the bucking), causing it to jam. And check your loading nozzle, I'm betting your loading ramp has broken. The WE loading nozzles break easily, get a better one if possible! Hope that helps!
I have a WE G18C GEN4 and the nozzle is break :( What's your nozzle ? And where did you buy the Nozzle ? Please :) Thanks You (Sorry for my English, I'm French)
The manual says the parts of g-83 are not on your video. But it works well without it. Did I need this part? It's a little awkward... : ( And I hope the translator work well: )
Hmm sounds pretty weird, does it overfeed on semi? Best thing to do is to look at my loading nozzle in this video and see if it looks similar to yours via loading ramp. If its damaged then I'd replace it, with a glock 17 loading nozzle (you just shave off the right nub) But it might not be the loading nozzle now that its still feeding...send me a video if you want, make sure you are stacking the bb's correct too
I bought RA Tech inner barrel and it says for WE G18 97mm in length. Do you know if it's going to work for my TM G18 by any chance? I didn't hear you mentioning about this. Nice and very detailed video btw I'm def subscribing.
Hey I lost the spring and the other piece on the fire selector and I was wondering if that effects anything. And also I am having the problem that it fires on automatic when it is on semi, I was trying to fix it when I lost the part.
the spring that you said pops out. please let me know if you know where to get one . ordered what I believed to be the same thing and was way smaller than original .
Sorry I keep asking u questions about the paint removing. Did u use paint THINNER or REMOVER and if I just removes the paint on the slide and that's all I did would everything fit ok. I do not want to screw up my pistol.
Ok, I'll try and make avid when I finish work. Also what length inner barrel do you have? I have ordered a compensator and want to upgrade the barrel when I put the compensator on.
Fixed it. It was just a hop up adjustment issue, will a high cap tightbore fit? The only ones im finding online at a decent price are 7inch high cap tightbores meant for gbb pistols.......
my hammer wont reset after i rack the slide. The hammer stays in the "firing" position and it wont come out. when i pull the trigger the gun doesnt even make a click
I stripped mine(it had a feed problem) too many bb's in the chamber at once, when I put it back together the slide jams half way down the body when I slide it in. Any ideas? Excellent video btw....
ya i used tape to hold it in place. i have left over pieces that came with the slide. 2 tiny ball bearings and a tiny metal piece. (???) Side note slide wont rack smooth and my selector won't switch off semi. any ideas? playing around with it ATM. (No frame work has been done yet only slide.)
and by rack i just mean it gets stuck to rear and then you have to smack it forward. :( Stumped ATM. (Shooters Design Zev Tech for TM G18C) cause i didn't mention it.
ok so i got an asg glock 18c, and with the spring the gun jams just like yours, but without it, the slide goes back fluently. i dunno what's wrong with it, i think i'm misplacing the spring, but somehow the barrel won't move with the spring in
Nice video man, i just wanted to ask u what type of loading nuzzle did u use because mine has just broke in less than a week and i can't find any replacement for that because is different from other glocks,thanks
Hello KnuclesGSM, I have a question for you: the nozzle of my WE G18c broke (the spring catching part you know..). Is there anyway to buy an aluminium nozzle or something more durable than the original plastic one. I am ready to change other parts if I have to do so. My G18C is mounted in a CAA RONI, that's why I realy mistreat it and need to reinforce it haha ;). I also found an Angel Custom red one, but it's also polymer made and I don't know if I can get it in France. Best regards and nice videos ;)
Thanks for replying. Fixed that issue but now its overfeeding aftef 1 shot. Any other ideas or do you think its the nozzle again? If so what better quality one fits? Thanks...
hi not sure if you explained it in the video i might have missed it what is the little slider under the frame on the front part of the gun has a number on it and little arrow
if it dosent have the return spring in the blowback housing will the gun stop shooting because that is my problem rn i dont know if its soming on the lower part of the gun or the top
Can you help me! My slide is doing the same thing yours did at the end were it just stops instead of going all the way and i just got mine two days ago. I dont know how to fix it when i take the slide off i can see it scratching the paint of the frame. It may be because its not lubed up or like you said the hammer screw isn't tightened if so can you give me some instructions or in anyway help thanks!
Hey I know this is a super old video, but I have the same non-locking issue that's shown at the end of the video. Although I didn't touch the hammer assembly screw? Any help you could give me?
i had the exactly same thing with my we g18c, i just bought it, i brought it home, took it apart, then put it back together and thats it, the slide will not go back after cocking it, the same hapened when i tried to shoot it, did you figure it out??? pls tell me what you did, sory my speling is terrible i am foreign as hell))) by the way great chanel
You're a lifesaver dude! Didn't know where to put the hopup arm back and your explanation/video did the trick! Thanks!!
Hi, can I say right now that this a such a fantastic and useful channel, your explanations are thorough yet quick so it doesn’t take too long, this re-assembly helped me so so so much and I literally cannot thank you enough!
Instructions not clear
Created a 1911
xΔ
Just kiddn'!
One of the best assembly's I have seen!
Thanks man! I just fixed my gun only disassembly and assembly by watching you.
I cannot express thankful I am and how much you were able to save my g18 with your series of videos. I too had broken my loading nozzle which I was able to fix with some adhesive. The spring I had to straighten for close to an hour however. While watching your videos I found the issue as I had never used a WE glock before and knew very little about its inner workings. It was only a matter of time before the nozzle broke which I knew from the start, but these pistols are cheap and easy to upgrade as far as the slide goes. Evike has started to sell the nozzles again on there website under angel custom with a new polycarbonate red material. If anyone does not want to spend the money on buying a new one, you can simply take the nozzle, put adhesive glue on the broken corner and the corresponding broken piece and let them dry together, afterwards you can then layer the back of the chipped piece to reinforce it. From my knowledge this lasts over several hundred rounds until you repeat the process. I hope this helped someone as much as your videos helped me. Keep up the great work man!
Don’t quote me on this but I had same problem a punk to take slide back off. I’m sure that when u put the recoil spring back on you pushed it to high in the slide. I levelled the recoil to be straight then it was sweet as. Oh yeah should mention that grease and lube as you go.
Either way thanks you bloody LEGEND!!!!
Great video dude! thanks for this detailed explanation
It will be based on what you use, if you don't have experience with paint thinner and metals I would probably google it and see what you can find.
omg thank you, i was stuck on the slide release for hours, and yea, we got the same gun bro!
Finally somebody with decent light over black parts 😬
thanks dude, I fixed my G!
This is a lot like a real g17
This video saved my life thank you
Tks a lot, I was having a had time to fit the slide catch.
Men, you save my day.
I've a G23c WE It's impossible to found a fucking explosed view of it and found how to put in this fucking mag release button! THANK YOU MAN!
np bud!
if you take out the follower, it will help it a little bit, but in general (even RS) most people warn against dry firing, so its up to you in the end
Holy, thank you
my mag release dropped out
only you could tell me how to apply the spring, thx so much. I was ready to buy a new one
Thank you for this video, and correct me if I'm wrong but you half tightened your hammer assembly screw and never fully tightened it.
Dont know if i should be proud but i am 14 and now know how to fully take apart a WE g18 😁
Nice man! Glad to hear that you fixed it and yes Hi-Capa barrels will fit in it! :)
I think you may have forgotten to tighten the hammer housing screw
Hey, I tried to rebuild my slide but when I finished when I cock it it stops about 2mm away from where it’s supposed to but if I tap it it goes back, I tried firing it but it sticks holding the green gas button and dosnt do anything but release green gas. If anyone could me understand what I did wrong it would be a huge help
Helped me out! Quality vid, and it makes you wonder how they do it in the factory
They sell complete kits, check out MAG overseas
Silicon oil , great build!
Thanks a lot for showing me how to put the hop-up part back together...
nevermind i got it working the right way and thank you for your help. keep up your helpful videos man.
It will only work for the Gen3 grip, not the gen4 grip so make sure you get the right grip! :)
FYI: Upper or slide assembly begins at 8:22
Just in case that is your only concern. Beginning of the video is all about the lower or the pistol frame.
Enjoy!
The inner barrel is a 7inch 6.01 PDI, its a good length for the comp that I have on it right now! Hope that helps, and let me know when you get that video, try to show the problem as well or whatever works! :)
I would check the hammer assembly, something could be broken in the assembly, hammer, spring, sear
3:02 People, make sure your hammer assembly is cocked, when you reassemble it back to the gun, otherwise your trigger will not reset correctly after the final shot.
Thank u this helped me so much
Hey Cheese didn't see this question, WE fill valves work with WE mags, (Proarms work with TM) different threading so need to becareful! ^_^
It needs to go in before you put in the BBU, and its tricky putting in the BBU with that being in place, just becomes a balancing game haha
Maybe installed something wrong? Watch the video over and see if you missed anything
It sounds like your bucking overswelled (replace the bucking), causing it to jam. And check your loading nozzle, I'm betting your loading ramp has broken. The WE loading nozzles break easily, get a better one if possible! Hope that helps!
Very informative thanks
I have a WE G18C GEN4 and the nozzle is break :( What's your nozzle ? And where did you buy the Nozzle ? Please :) Thanks You (Sorry for my English, I'm French)
YZAK it is a g17 nozzle that i modded to fit into a g18
The manual says the parts of g-83 are not on your video. But it works well without it. Did I need this part? It's a little awkward... : (
And I hope the translator work well: )
ummm.... I found it. thank you for your video
No, thats the Guns Modify Aluminum Trigger, replaced the plastic one. Hope that helps! ^_ ^
Thank you so much, finally found a good video
np bud
I just had the same problem and the only thing that solved it was not tightening the rear sight so much? Weird.
thanks for the tutorial elmer fud
great vid thank you
proarms fill valves will work just fine, evike has them
Man,
U just saved me. Thanks!
i found this video very helpful. thank you!
It was a dumb mistake, didn't tighten the screw for the hammer chasis!
you didn’t fully screw in the hammer assembly screw
Hmm sounds pretty weird, does it overfeed on semi? Best thing to do is to look at my loading nozzle in this video and see if it looks similar to yours via loading ramp. If its damaged then I'd replace it, with a glock 17 loading nozzle (you just shave off the right nub) But it might not be the loading nozzle now that its still feeding...send me a video if you want, make sure you are stacking the bb's correct too
Good eyes buddy! Exactly what I forgot to do -_- lol
I bought RA Tech inner barrel and it says for WE G18 97mm in length. Do you know if it's going to work for my TM G18 by any chance? I didn't hear you mentioning about this. Nice and very detailed video btw I'm def subscribing.
You are the best...... Excelente tu video, gracias a ti le hice mantenimiento a mis Glock..
got it from tokyo model company, its by EAC
only thing i have left to ask is how to properly install the extractor on a shooters design slide.
thanks man, and that would be interesting to learn :)
Hey I lost the spring and the other piece on the fire selector and I was wondering if that effects anything. And also I am having the problem that it fires on automatic when it is on semi, I was trying to fix it when I lost the part.
Sounds good man! :)
the spring that you said pops out. please let me know if you know where to get one . ordered what I believed to be the same thing and was way smaller than original .
i have the gen3 grip :) thanks a lot man!
Sorry I keep asking u questions about the paint removing. Did u use paint THINNER or REMOVER and if I just removes the paint on the slide and that's all I did would everything fit ok. I do not want to screw up my pistol.
won't work, you can't put a full auto and a semi lower
Link me to the slide you got, the ball bearings are usually for the selector switch
Ok, I'll try and make avid when I finish work. Also what length inner barrel do you have? I have ordered a compensator and want to upgrade the barrel when I put the compensator on.
thank you very much for your video my really help me
Fixed it. It was just a hop up adjustment issue, will a high cap tightbore fit? The only ones im finding online at a decent price are 7inch high cap tightbores meant for gbb pistols.......
Thanks.
my hammer wont reset after i rack the slide. The hammer stays in the "firing" position and it wont come out. when i pull the trigger the gun doesnt even make a click
I stripped mine(it had a feed problem) too many bb's in the chamber at once, when I put it back together the slide jams half way down the body when I slide it in. Any ideas? Excellent video btw....
Thank You! subbed
ya i used tape to hold it in place. i have left over pieces that came with the slide. 2 tiny ball bearings and a tiny metal piece. (???)
Side note slide wont rack smooth and my selector won't switch off semi. any ideas? playing around with it ATM. (No frame work has been done yet only slide.)
easy, remove the magazine follower and the spring inside of the magazine and you are set!
Why the whole gun? I removed all the parts out of the slide because that is the only partni am removing the paint from.
and by rack i just mean it gets stuck to rear and then you have to smack it forward. :( Stumped ATM. (Shooters Design Zev Tech for TM G18C) cause i didn't mention it.
ok so i got an asg glock 18c, and with the spring the gun jams just like yours, but without it, the slide goes back fluently. i dunno what's wrong with it, i think i'm misplacing the spring, but somehow the barrel won't move with the spring in
Nice video man, i just wanted to ask u what type of loading nuzzle did u use because mine has just broke in less than a week and i can't find any replacement for that because is different from other glocks,thanks
Hello KnuclesGSM,
I have a question for you: the nozzle of my WE G18c broke (the spring catching part you know..). Is there anyway to buy an aluminium nozzle or something more durable than the original plastic one. I am ready to change other parts if I have to do so. My G18C is mounted in a CAA RONI, that's why I realy mistreat it and need to reinforce it haha ;). I also found an Angel Custom red one, but it's also polymer made and I don't know if I can get it in France.
Best regards and nice videos ;)
Ok. How did u apply it. And remove it. I have some experience with paint thinner and I have watched some vids on it
Do you know what replacement fill valves will fit the mag? Will all WE fill valves work?
Can I get a link to the hammer assembly??? Mine broke
no problem :)
Thanks for replying. Fixed that issue but now its overfeeding aftef 1 shot. Any other ideas or do you think its the nozzle again? If so what better quality one fits? Thanks...
hi not sure if you explained it in the video i might have missed it what is the little slider under the frame on the front part of the gun has a number on it and little arrow
Can you do a video about your front end mod kit on this gun, I was thinking of getting one but I can't find a single video on here, thanks
if it dosent have the return spring in the blowback housing will the gun stop shooting because that is my problem rn i dont know if its soming on the lower part of the gun or the top
Can you help me!
My slide is doing the same thing yours did at the end were it just stops instead of going all the way and i just got mine two days ago. I dont know how to fix it when i take the slide off i can see it scratching the paint of the frame. It may be because its not lubed up or like you said the hammer screw isn't tightened if so can you give me some instructions or in anyway help thanks!
You need to return it if its already messing up and new
Did the paint just come off or did u scrape it or something. How long did it take
What am I supposed to do? Am I missing a spring?
Bruh there's one part that isn't shown in this video, I've put it all together and got one piece leftover tf
and is the marui fram compatible
Hey I know this is a super old video, but I have the same non-locking issue that's shown at the end of the video. Although I didn't touch the hammer assembly screw? Any help you could give me?
is the guarder steel magazine catch for marui gbb compatible with the we g18c?
It's a tm mag
Really good video just too fast near the end because that’s he only bit I needed help with but you rushed it a bit
Theres a small cylindrical piece that fell out. Is it important? Where do i put it?
Just watch the videos, or youtube others, I know some have made videos of paint thinning slides, hope that helps!
The slide lock isn't springer like yours
i lost the parts in my selector switch aswell, can you buy them anywhere?
Tank you for let me know. soooow kind
i had the exactly same thing with my we g18c, i just bought it, i brought it home, took it apart, then put it back together and thats it, the slide will not go back after cocking it, the same hapened when i tried to shoot it, did you figure it out??? pls tell me what you did, sory my speling is terrible i am foreign as hell))) by the way great chanel
Cool! I've heard that if airsoft guns (mostly GBBs) are dry-firing, it can ruin the gun's intended function. Is this true?