I have a 2018 Nissan Altima, and it started with a loud consistent ticking sound, and was noticing it suspiciously went away after it warmed up. Also, it was unbelievably "exhausty" in the cabin and under the hood. This absolutely solidified my suspicions. Thank you!!
This is very helpful in explaining the ticking noise I hear when my engine is cold. Mine goes away usually within 30 seconds or less, so probably a smaller leak than average but still a problem to look at.
dont normally subscribe to pages like auto cars but you guys deserve it! The video was clear, concise, and repetitive with important tips and information! Great vid guys!
Confirms what my mechanic told me. My truck is in the shop right now getting a new manifold on the right side. That's where I started hearing the ticking sound. In fact I hear this sound in a lot of vehicles. Yeah, my next door neighbor who hasn't gotten hers checked out yet. Thanks for a great commentary on this. I subscribed to your channel and gave you a thumbs up.
@@holtman2598 : That's more likely to be a loose "V", or "serpentine" belt than a leaking manifold. Rub a bit of bar soap, or perhaps a bit of Dawn onto each belt, if it stops squealing you've found the "offender". The next step is to re-tension the belt. If the belt won't re-tension, or resumes the squealing it may be time to replace the belt. If you end up replacing the belt, make certain to get the proper amount of tension applied to it. Remember, the application of soap to the belt/s is ONLY a "diagnostic tool", NOT a repair!
So that’s what that noise is on my passenger side, it’s starting to continue to tick even with the car warmed up unless I drive for a while which I usually don’t. Now I have a good idea of what I’ll be getting repaired. Thanks for that! Great video man, you know your stuff!
Soap and water. Use a shop vac on the blow side in your exhaust to find a leak on joints and seams instead of going by noise. Itll also keep it all cold so you can touch and work on the exhaust
What if you have ticking that doesn’t stop as it gets hot but it does slightly reduce? Also when car is up off the ground and your under it you can feel a whoosh of exhaust when have a buddy slightly torque the engine putting it in drive and break torquing it and facing where the pipe comes down to the cat. Can also smell exhaust in the engine bay back where the manifold is hidden behind the engine but no whooshing of exhaust blowing upwards like is under. The issue is we don’t think it’s manifold, sounds like leaking manifold but the whooshing underneath makes us think it’s elsewhere, that large of a leak in the manifold would likely poisoned me on a road trip by now makes us think that the leak is further down stream but just above the cat. But we can’t locate it and it’s a huge job to replace it because looks like have to drop the subframe and no one wants to do that.
Awesome video, I was about to just tighten up my bolts there but after seeing how bad the surfaces can get and that cracks can show up, I'll take out the manifold and give it a better inspection. Also hadn't even thought to use my hand to feel for gasses when the car is just turned on
Man I really appreciate all these high quality videos yall put out. I was able to rebuild my moms trailblazer 4.2 inline 6 engine from your videos (and the help of other videos), but primarily yours with the trailblazer 4.2 timing chain video. The engine is now now operating even better than before and i just started noticing the ticking on the exhaust side. I was bummed thinking it was something worse, but i highly suspect it is a leak at the manifold. It's a high milage vehicle, so I replaced all the gaskets on for the manifold, but never inspected the old manifold before installation on the rebuilt. All the research ive done, point me to the exhuast manifold being compromised. thanks again
My aunt once had a car that would blow anti-freeze in through the a/c vents. I was a kid and didn't understand the reasoning behind it. But I can remember looking at the vent and wondering why the air coming out of it was... visible to some degree
I've been trying for about 6 months to figure out what is going on with my truck. You explained it perfectly and diagnosed my exact problem. When I find the leak I will buy my replacement parts from 1aauto. TY
Simple way to check leaks is to use soapy water and test to see where bubbles comes. Apply soapy water on possible leaks area first. If you have leak in exhaust prior to catalyst, you will see 420 and 430 code and engine light on. I don’t why some will open all parts first and use eye ball to inspect the leak.
The best way to check for an exhaust leak, is to use a shop vac. Insert the shop vac end into the open end of the exhaust pipe and if you have dual pipes with a crossover pipe you'll need to block the other pipe by inserting an old t-shirt or shop rag. You'll want the shop vac blowing air into the exhaust pipe. Now, you don't have to worry about the exhaust leak sealing off due to heat, just grab yourself a spray bottle of water and dish soap. Go along spraying the soapy water and as soon as you see bubbles you'll have found your leak.. but don't stop there, there could be more.
Very informative. I just got a 2006 Honda Element that had a bad donut gasket and I just fixed that (what a relief for the ears!), but I found it ticks under load, whether the engine is hot or cold (the ticking under load doesn't go away when the engine is warm). Could this mean the manifold itself is fine but the gasket is bad? There are no leaks coming from the new donut. Thanks in advance for your comments.
Hi there, would the typical 'ticking' sound you mentioned of a leak very close to the engine be the short ticking noise I can hear right at the very beginning of the video when the engine starts? I have exactly that sound, I hear it mainly while driving whenever the motor has to pull, when I accellerate. This sound is getting louder and started over a year ago, however doesn't go away when the motor is heated up. Thanks in advance for your help!
I'm having the same issue and it's ever since I put a new set of aftermarket headers on. It seems to get worse when it's warm and will only make the sound under load. I can't for the life of me figure out what it is, it's definitely not the valve lifters as the sound isn't coming from them.
So you're saying that if my manifold is connected to my catalytic converter I can get a lien condition as well as a p0420 or p04302 my manifold is leaking correct or not there's nothing wrong with the O2 sensors are replaced it twice already
My car got the same code. It smells like gas when I turn on the AC or the heater. I’m assuming it’s coming from under the hood. I used cataclean n cleared the code so it hasn’t popped up and it’s been longer than a month.
I got my response after many months trying to understand why I have an exhaust buzzing noise between 1500 RPm and 2000 RPM when engine is warming up. Noise almost disappears when the exhaust system reaches a very hot temperature (Heavy traffic driving for 20 minutes). Then the noise comes back slowly when cruising at high continuous speeds (When exhaust system cools down due to the cooling system and high airflow underneath the car)
or you could use a shop vacuum with it blowing not sucking and with everything cold put the shop vac in the exhaust tip and tape to so it doesnt fall out and then turn it on and take soapy water and spray down the exhaust that is the easiest way to check for an exhaust leak been doing this for years as a auto tech BUTTTT make sure the motor and exhaust are not hot and it hasn't been ran for a couple hours
When I turn my car off and it’s parked I hear a very rapid ticking noise like someone it tapping a small wrench really fast near the back or mid section of my exhaust and this noise actually goes away once the system is cooled off. But I hear no ticking when the car is on…I have taken it to 4 mechanics and they have told me there isn’t a problem. I’m not convinced.
Okay so I have a 2017 ram 1500 penstar engine and I have a ticking noise in think it was engine related but watching this makes me second guess. So in the morning is when it’s the worse as it would be if engine related and it gets quieter but doesn’t go away completely and it does increase under acceleration. So my question to you is it even worth what you think it could be
My 2007 Chevy 4.8 makes a ticking/tapping sound only after the engine is at operating temperature. The noise sounds exactly like lifter tapping but goes away after a few minutes. Back in the day of muscle cars that was indicative of an exhaust manifold leak. My guess is that when the thermostat opens up and the water starts to flow through the aluminum heads, they react to the quick temp change. But the manifolds being cast iron are not getting any cool down effect. So maybe this is why the tapping sound only happens at that time (operating temp) and not at start up or constant while the engine is running the whole time. Just guessing. Gong to try the shop-vac thing and see. But not sure it will help seeing it only taps after it's warm and for a few minutes, then it goes away and purrs like a kitten for the rest of the time.
+Mel64D We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Jeez I just had some shorty headers installed on my 2013 F150 I also hear a slight ticking noise in the morning; must be a very small leak cause it goes away in the day
That “Donut gasket” piece, is that referred to as a “Flange gasket”!? Because, I can’t find it on the site under the name you referred to it as! However, I see a “Flange gasket” & that looks like what you’re showing us.
Looks like I have a an exhaust manifold leak. I can see it bubbling. I am also loosing coolant and have white smoke. Does that make sense? Do I also have an intake manifold leak??? Vehicle is a 1989 F240 with a 460 7.5.
Hello everyone, question: do you need to replace that if you have the leak. If the sound doesn't bother you or there will be some other complication if not replaced. And if you do need to replace that for some reason, what is the longes you can drive without replacing it if the sound just appeared?
im working on a 2003 gmc savana van, i hear a ticking when started up cold but i still hearing the ticking even when its warm, but when i drive it and give it some gas it goes away but comes back when im idling what does that mean? also symptom on possible maifold leak?
I have a leak coming from where the donut gasket is. Could this be a leaking coming from somewhere else and just happen to find it’s way where this part is!
I have a Nissan 2018 Frontier King Cab 4cyc with an exhaust leak at the exhaust intake manifold not at the head but a little waist down where it's covered by heat Shield bolted in another one a little further down which is clamped together where to exhaust pipes meet and is covered by heat shield it has a aluminum o-ring as a gasket how do I get them off to replace the aluminum o-ring on it
@1auto Lenny Would it cause smokey from manifold gasket too? or would that be the valve cover gasket only? I changed my water pump in my 3.9v6 Dakota at start up to burp system passenger side, started to smoke really bad. Was told its valve cover gasket but Im pretty set its mainifold gasket.
I don’t get a ticking noise. It sounds more like chirping or squeaking, or even metal to metal when I accelerate. It is less audible when the engine warms up. Does this still sound like an exhaust manifold issue? Gasket? Loose bolt(s)?
Hi I tore my manifolds off. I have multiple broken manifold bolts as well as shot gaskets. My truck makes a ticking noise that is louder when cold but doesn't go away when truck is warm either. Could this be my problem? 2014 dodge ram 1500
Does anybody know if a manifold pre cat like shown is supposed to build up heat while at idle? Mine measured 330 into manifold 550 at the front of the cat and 330-350 at the back. Does this mean this pre cat is bad or that it is functioning? Once again these were measurements at idle
Anybody know what could possibly be causing my vehicle to tick after a cat delete it’s a very loud ticking noise that will eventually die off once my vehicle has shifted through gears
Can anyone help me with this, pleas? My engine has the ticking when I start it. It is gone after the engine warms up idling but the ticking resumes as soon as I hit the accelerator. I can be going down the road at 5 MPH and if my foot is on the accelerator I hear the ticking but if I remove my foot from the accelerator at that point the ticking goes away. It comes right back if I hit the gas pedal again.
Buy aftermarket bolts, the ones used are grade 8 I believe but go with a grade 9 or 10. Just take an intact bolt into a bolt shop and get them to match up width, length and thread 😘
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Do I need schooling to be a mechanic, I got 3.8 GPA I'm trying to get a scholarship to get into a good mechanic college, any advice?
This will only work if you are working on a verical. Unfortunately many of us only have a vehicle. One day I too will drive a verical.
veerlecle
Vericle 😂
I have a 2018 Nissan Altima, and it started with a loud consistent ticking sound, and was noticing it suspiciously went away after it warmed up. Also, it was unbelievably "exhausty" in the cabin and under the hood. This absolutely solidified my suspicions. Thank you!!
This is very helpful in explaining the ticking noise I hear when my engine is cold. Mine goes away usually within 30 seconds or less, so probably a smaller leak than average but still a problem to look at.
Or... your lifters.
@@wheresfuninthat you beat me to it🤣
@@coreymohn05 mine is the other way around it ticks on startup and when I rev it
dont normally subscribe to pages like auto cars but you guys deserve it! The video was clear, concise, and repetitive with important tips and information! Great vid guys!
"Front of the vericle, or rear of the vericle?" 😂 I'm sorry I couldn't resist .I love your content! Thanks for all your time and knowledge shared!
Great video, especially love how the guys often pronounced vehicle, "vericle" :D
Confirms what my mechanic told me. My truck is in the shop right now getting a new manifold on the right side. That's where I started hearing the ticking sound. In fact I hear this sound in a lot of vehicles. Yeah, my next door neighbor who hasn't gotten hers checked out yet. Thanks for a great commentary on this. I subscribed to your channel and gave you a thumbs up.
Verical?
I’m glad you said something lol because I was about to say really no one else is hearing this shit lmao 😂
Very instructive and well explained, showing that you got an experience gained from long practice. 👍👏👏
+Tico Zico Thanks for the feedback!
@@1AAuto my 98 ram squeals when I accelerate, it's pretty quiet but gets annoying after a bit and tends to get quiet the longer I drive
@@holtman2598 :
That's more likely to be a loose "V", or "serpentine" belt than a leaking manifold.
Rub a bit of bar soap, or perhaps a bit of Dawn onto each belt, if it stops squealing you've found the "offender".
The next step is to re-tension the belt.
If the belt won't re-tension, or resumes the squealing it may be time to replace the belt.
If you end up replacing the belt, make certain to get the proper amount of tension applied to it.
Remember, the application of soap to the belt/s is ONLY a "diagnostic tool", NOT a repair!
Dude, never thought auto stuff can be fun learning and easy fixing!
So that’s what that noise is on my passenger side, it’s starting to continue to tick even with the car warmed up unless I drive for a while which I usually don’t. Now I have a good idea of what I’ll be getting repaired. Thanks for that! Great video man, you know your stuff!
Soap and water. Use a shop vac on the blow side in your exhaust to find a leak on joints and seams instead of going by noise. Itll also keep it all cold so you can touch and work on the exhaust
What if you have ticking that doesn’t stop as it gets hot but it does slightly reduce? Also when car is up off the ground and your under it you can feel a whoosh of exhaust when have a buddy slightly torque the engine putting it in drive and break torquing it and facing where the pipe comes down to the cat. Can also smell exhaust in the engine bay back where the manifold is hidden behind the engine but no whooshing of exhaust blowing upwards like is under. The issue is we don’t think it’s manifold, sounds like leaking manifold but the whooshing underneath makes us think it’s elsewhere, that large of a leak in the manifold would likely poisoned me on a road trip by now makes us think that the leak is further down stream but just above the cat. But we can’t locate it and it’s a huge job to replace it because looks like have to drop the subframe and no one wants to do that.
Awesome video, thank you! great visuals, compact narration. After watching this My next truck is gonna be electric for sure!
Awesome video, I was about to just tighten up my bolts there but after seeing how bad the surfaces can get and that cracks can show up, I'll take out the manifold and give it a better inspection. Also hadn't even thought to use my hand to feel for gasses when the car is just turned on
Man I really appreciate all these high quality videos yall put out. I was able to rebuild my moms trailblazer 4.2 inline 6 engine from your videos (and the help of other videos), but primarily yours with the trailblazer 4.2 timing chain video. The engine is now now operating even better than before and i just started noticing the ticking on the exhaust side. I was bummed thinking it was something worse, but i highly suspect it is a leak at the manifold. It's a high milage vehicle, so I replaced all the gaskets on for the manifold, but never inspected the old manifold before installation on the rebuilt. All the research ive done, point me to the exhuast manifold being compromised. thanks again
This is the exact issue on my 2004 V8 4 Runner. Excellent video appreciate the step-by-step diagnosis
Could a leak come into the car ? I have noticed feeling dizzy/ light headed when driving at times
+Daniel T Thanks for watching! Yes a leaking exhaust could cause fumes to enter the cabin.
Hey man get that fixed immediately , thats really dangerous
Me too bro!
I was in my car during the winter and I was heating it up with the heater on and I fell asleep for like ten hours!
It took me a few days to shake it off! Thanks be to God Almighty that I am still up and alive 🙏🏽
My aunt once had a car that would blow anti-freeze in through the a/c vents. I was a kid and didn't understand the reasoning behind it. But I can remember looking at the vent and wondering why the air coming out of it was... visible to some degree
I've been trying for about 6 months to figure out what is going on with my truck. You explained it perfectly and diagnosed my exact problem. When I find the leak I will buy my replacement parts from 1aauto. TY
Drink every time he says “vericle” 😅😜
Just from watching I was able to easily identify my problem! Thanks a bunch y'all, greatly appreciate the video!
Simple way to check leaks is to use soapy water and test to see where bubbles comes. Apply soapy water on possible leaks area first. If you have leak in exhaust prior to catalyst, you will see 420 and 430 code and engine light on. I don’t why some will open all parts first and use eye ball to inspect the leak.
thanks for the video, the tips around the inspection of the manifold and parts helped me in diagnosing my issue 👍
smoke machine from the end of the exhaust is helpful - worked for me! thanks
The best way to check for an exhaust leak, is to use a shop vac. Insert the shop vac end into the open end of the exhaust pipe and if you have dual pipes with a crossover pipe you'll need to block the other pipe by inserting an old t-shirt or shop rag. You'll want the shop vac blowing air into the exhaust pipe. Now, you don't have to worry about the exhaust leak sealing off due to heat, just grab yourself a spray bottle of water and dish soap. Go along spraying the soapy water and as soon as you see bubbles you'll have found your leak.. but don't stop there, there could be more.
Very informative. I just got a 2006 Honda Element that had a bad donut gasket and I just fixed that (what a relief for the ears!), but I found it ticks under load, whether the engine is hot or cold (the ticking under load doesn't go away when the engine is warm). Could this mean the manifold itself is fine but the gasket is bad? There are no leaks coming from the new donut. Thanks in advance for your comments.
I love 1Aauto videos.
+K Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
shop vac in reverse taped to the exhaust and then soapy water the whole thing!!! Thanks for this detailed video!
+TheThreeLeggedChair Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I saw the video. What kind of leak is it? I mean what fluid means the leak goes through? Motor oil right?
Hi there, would the typical 'ticking' sound you mentioned of a leak very close to the engine be the short ticking noise I can hear right at the very beginning of the video when the engine starts? I have exactly that sound, I hear it mainly while driving whenever the motor has to pull, when I accellerate. This sound is getting louder and started over a year ago, however doesn't go away when the motor is heated up. Thanks in advance for your help!
Same
Could be your valves or valve lifters that need to be adjusted or could be rod knock which is not good
Look up what a rod knock sounds like.
I'm having the same issue and it's ever since I put a new set of aftermarket headers on. It seems to get worse when it's warm and will only make the sound under load. I can't for the life of me figure out what it is, it's definitely not the valve lifters as the sound isn't coming from them.
@@BreeingIan maybe it’s the EGR valve? Did you resolve it?
Thank you so much I will check out my Jetta for the possible air leaks you mentioned :)
So you're saying that if my manifold is connected to my catalytic converter I can get a lien condition as well as a p0420 or p04302 my manifold is leaking correct or not there's nothing wrong with the O2 sensors are replaced it twice already
Thats my same question, i have a code saying my manifold but a p0420 saying my catalytic converter, but the manifold leak could cause the code right?
My car got the same code. It smells like gas when I turn on the AC or the heater. I’m assuming it’s coming from under the hood. I used cataclean n cleared the code so it hasn’t popped up and it’s been longer than a month.
I like how he explains it in sign language as he goes along. Unless he's a mime irl. or symphony conductor. Or veeracle mechanic
I got my response after many months trying to understand why I have an exhaust buzzing noise between 1500 RPm and 2000 RPM when engine is warming up.
Noise almost disappears when the exhaust system reaches a very hot temperature (Heavy traffic driving for 20 minutes). Then the noise comes back slowly when cruising at high continuous speeds (When exhaust system cools down due to the cooling system and high airflow underneath the car)
or you could use a shop vacuum with it blowing not sucking and with everything cold put the shop vac in the exhaust tip and tape to so it doesnt fall out and then turn it on and take soapy water and spray down the exhaust that is the easiest way to check for an exhaust leak been doing this for years as a auto tech BUTTTT make sure the motor and exhaust are not hot and it hasn't been ran for a couple hours
It's people like you that makes me enjoy the internet. Thanks for the great idea man
Explanation, very thorough and clear. Thanks so much.
Awesome video and covered all the bases.
That’s a fact you just said the main problem I have with my axaust thank you sir.
Thank
I’m asking the grove of the Exhaust Manifold Gasket is towards the outside of the header ?
Plz answer
Great video........... very crystal clear the way you put it....
I love this channel and the technicians❤❤❤
Can you use a carbon monoxide tester to find a leak at the joints
The verical I'm working on is a jeep wrangler 01 tj. Hopefully I can find it after using this videur. It will be a miracure
Great video Lenny and see you at the rally on Friday!
When I turn my car off and it’s parked I hear a very rapid ticking noise like someone it tapping a small wrench really fast near the back or mid section of my exhaust and this noise actually goes away once the system is cooled off. But I hear no ticking when the car is on…I have taken it to 4 mechanics and they have told me there isn’t a problem. I’m not convinced.
great video with clear explanation. Thank you very much
Okay so I have a 2017 ram 1500 penstar engine and I have a ticking noise in think it was engine related but watching this makes me second guess. So in the morning is when it’s the worse as it would be if engine related and it gets quieter but doesn’t go away completely and it does increase under acceleration. So my question to you is it even worth what you think it could be
What is a “vehricle”?....haha jk
Good video thanks for the information!
Thanks found my leak it’s rear muffler joint , it’s even easy fix by joint exhaust band clamp
My 2007 Chevy 4.8 makes a ticking/tapping sound only after the engine is at operating temperature. The noise sounds exactly like lifter tapping but goes away after a few minutes. Back in the day of muscle cars that was indicative of an exhaust manifold leak. My guess is that when the thermostat opens up and the water starts to flow through the aluminum heads, they react to the quick temp change. But the manifolds being cast iron are not getting any cool down effect. So maybe this is why the tapping sound only happens at that time (operating temp) and not at start up or constant while the engine is running the whole time.
Just guessing. Gong to try the shop-vac thing and see. But not sure it will help seeing it only taps after it's warm and for a few minutes, then it goes away and purrs like a kitten for the rest of the time.
+Mel64D We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Great detailed video, thank you!
I changed my exhaust manifold bolts and gasket but a smoke coming from the engine bay is it normal for a new manifold ?
Jeez I just had some shorty headers installed on my 2013 F150 I also hear a slight ticking noise in the morning; must be a very small leak cause it goes away in the day
As a female I thank you for explaining this with language that I can understand. You're awesome!
Except that one word he kept using. I think it was "Veerickle". I haber no clue what that means. Otherwise informative!
at 0:35, "you wanna start up the beericle" -- he says it a few times. is this some kind of regional thing?
Can I resurface my manifold mating surface flat or do I have to leave the raised rings around the ports
great vid and explanation- i am convinced my exhaust manifold is cracked and or damaged😅
I was about to start tearing my hair out but it looks like it'll be the whole exhaust instead lol. Thank you!
That “Donut gasket” piece, is that referred to as a “Flange gasket”!? Because, I can’t find it on the site under the name you referred to it as! However, I see a “Flange gasket” & that looks like what you’re showing us.
Looks like I have a an exhaust manifold leak. I can see it bubbling. I am also loosing coolant and have white smoke. Does that make sense? Do I also have an intake manifold leak??? Vehicle is a 1989 F240 with a 460 7.5.
Great video! Extremely helpful, thanks.
Your my hero I want to be like you when I grow up
Hello everyone, question: do you need to replace that if you have the leak. If the sound doesn't bother you or there will be some other complication if not replaced. And if you do need to replace that for some reason, what is the longes you can drive without replacing it if the sound just appeared?
Can an a manifold leak cause a burning smell when accelerating down the road or on the hwy?
Hello, I’ve got a question that’s been on my mind. Since an exhaust system is pressurized, how can it suck in air and create a lean condition?
Cracks in the seals
Extra air going to the O2 sensor. Venturi effect.
@@reginaldbowls7180 that would make it rich. O2 sensor would sense excess air and tell the engine to send more fuel
It’ll cause it to smoke a bit, when running lean
Subscribed!!!
A lot of hugs from Portugal!!!!
Do the manifolds bolts tend to get lose over time?
im working on a 2003 gmc savana van, i hear a ticking when started up cold but i still hearing the ticking even when its warm, but when i drive it and give it some gas it goes away but comes back when im idling what does that mean? also symptom on possible maifold leak?
Thanks for the video! I was finally able to repair my verricle.
I have a leak coming from where the donut gasket is. Could this be a leaking coming from somewhere else and just happen to find it’s way where this part is!
Pretty awesome troubleshooting video. A1 - thank uou for your great videos.
EXCELLENT VIDEO. VERY CLEAR AND INFORMATIVE!
+Gooseberry Dell Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com:
1aau.to/m/Shop-1AAuto-c
excelllent this is my exact problem with may 2010 nissian rouge.
Thanks for teaching🙏🙏🙏🙏🙏👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👌👌👌👌👌👌✌👋
You guys are ALWAYS on point! Love it!
Super great video. Thank you
I have a Nissan 2018 Frontier King Cab 4cyc with an exhaust leak at the exhaust intake manifold not at the head but a little waist down where it's covered by heat Shield bolted in another one a little further down which is clamped together where to exhaust pipes meet and is covered by heat shield it has a aluminum o-ring as a gasket how do I get them off to replace the aluminum o-ring on it
What if the ticking noise doesnt go away?
Excellent Video! Very informative
is leaking from manifold gonna cause any problem or just a noice? ?
@1auto Lenny
Would it cause smokey from manifold gasket too?
or would that be the valve cover gasket only?
I changed my water pump in my 3.9v6 Dakota at start up to burp system passenger side, started to smoke really bad.
Was told its valve cover gasket but Im pretty set its mainifold gasket.
I don’t get a ticking noise. It sounds more like chirping or squeaking, or even metal to metal when I accelerate. It is less audible when the engine warms up. Does this still sound like an exhaust manifold issue? Gasket? Loose bolt(s)?
Will this exhaust leak on the exhast manifold cause a p0420 code
Where are you guys located I would love to take my van to you guys
Will a leak cause smoke to come out from exhaust??
Hi I tore my manifolds off. I have multiple broken manifold bolts as well as shot gaskets. My truck makes a ticking noise that is louder when cold but doesn't go away when truck is warm either. Could this be my problem? 2014 dodge ram 1500
This was helpful. I now know that the manifold is not my problem.
I installed a new catalytic converter on my kia soul 1.6l and after starting the engine i notice a burning smell . Could it be cause its new?
Does anybody know if a manifold pre cat like shown is supposed to build up heat while at idle? Mine measured 330 into manifold 550 at the front of the cat and 330-350 at the back. Does this mean this pre cat is bad or that it is functioning? Once again these were measurements at idle
Awesome video dude, cheers 🥂
Anybody know what could possibly be causing my vehicle to tick after a cat delete it’s a very loud ticking noise that will eventually die off once my vehicle has shifted through gears
I would really like a video of what the ticking noise sounds like
Can you have a leak with no engine light? I still here ticking when my truck is warmed up. (03 5.4 ford)
This guy kind of moves like a butterfly
I don't know if my timing is out or my exhaust manifold is leaking. Hoping it's the latter.
So where is the leak coming from if the ticking does not go away when the engine heats up?
Can anyone help me with this, pleas? My engine has the ticking when I start it. It is gone after the engine warms up idling but the ticking resumes as soon as I hit the accelerator. I can be going down the road at 5 MPH and if my foot is on the accelerator I hear the ticking but if I remove my foot from the accelerator at that point the ticking goes away. It comes right back if I hit the gas pedal again.
How do you "PERMANENTLY" fix the constantly breaking exhaust manifold bolts on Ram trucks with 5.7 Hemi's?
Buy aftermarket bolts, the ones used are grade 8 I believe but go with a grade 9 or 10. Just take an intact bolt into a bolt shop and get them to match up width, length and thread 😘
Sell it and buy a Toyota
@@Nikkk6969 Yeah i havent quite hit my mid 40s midlife crisis yet, ill get back to you on that.
Very helpful video
+Jake Kenny Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
This was a great video, thanks