Stihl 024 AV Chainsaw Carb and Impulse Line Replacement

แชร์
ฝัง
  • เผยแพร่เมื่อ 1 ม.ค. 2025

ความคิดเห็น •

  • @trusted7060
    @trusted7060 2 ปีที่แล้ว +9

    i know this is a year old vid but i cant help sending you a suggestion or 2. first the fuel line is in backwards second there are 2 ways to take that throttle linkage out, the easiest is to take the one screw out of the back of the handle and taking it off, the other is to roll the throttle lever down and use a small screw driver to drop the linkage off the arm in a down ward motion.

  • @stihlhead3338
    @stihlhead3338 2 ปีที่แล้ว +4

    The 024/026 doesn't call for a intake or carburetor gasket. It probably won't hurt but it's not necessary.

  • @turbinepower77
    @turbinepower77 ปีที่แล้ว +2

    Your fuel line is installed upside down. The "s" bend goes in the tank.

  • @josephdalonges8718
    @josephdalonges8718 ปีที่แล้ว +2

    Your fuel line is backwards. The part you have hooked to the carb should be inside the tank.

  • @danjohnson5932
    @danjohnson5932 2 ปีที่แล้ว +5

    Take the screw out of the bottom of the handle remove the black cover, disconnect the linkage at the handle end and you don't have to wrestle with the linkage.

    • @piloux9915
      @piloux9915 2 ปีที่แล้ว

      Hello...justement voici mon problème ....La tringle d'accélérateur ! !pas trouvé pour démonté le couvercle de poignée et de raccrocher la tringle sur le carburateur. ..Merci à bientôt
      En français impec!

    • @tylerhowell6182
      @tylerhowell6182 ปีที่แล้ว

      Took the words right out of my mouth

  • @richierich7668
    @richierich7668 ปีที่แล้ว +1

    It would have just been easier to take the saw apart.then you can go in and clean your saw up and check other things as well but I noticed on your video you didn't show that you hooked up the in pulse line in the back you threw it all together and I watched the video twice.

  • @larrygilbert863
    @larrygilbert863 2 ปีที่แล้ว

    Thank you. Very well done explanation and video. I did not want to take all apart to replace the impulse tube. Thank you

  • @bryanhusk6105
    @bryanhusk6105 8 หลายเดือนก่อน

    Thank you

  • @danholmes9212
    @danholmes9212 2 ปีที่แล้ว +2

    Should be felt on the air cleaner looks like someone scraped it all off with a wire brush

    • @cowcatcher9186
      @cowcatcher9186 2 ปีที่แล้ว

      Yeah that air filter is shot. I guess it will keep a log from getting sucked into the carb.

  • @magicone9327
    @magicone9327 7 หลายเดือนก่อน

    When removing throttle linkage. Open throttle then put a screw driver into and under the butterfly to hold it open then release the throttle and it will fall off!

  • @darrellepickering8433
    @darrellepickering8433 ปีที่แล้ว

    Geez! Take a look at that air filter! Most of the flocking's gone! Seen that before where someone took a wire brush to it thinking it was dirty. If you use that it'll ingest dirt!

  • @sillyfruitcake
    @sillyfruitcake 3 ปีที่แล้ว +1

    that damn throttle clip is a bish isnt it lol

    • @in-depthdiy2123
      @in-depthdiy2123  3 ปีที่แล้ว

      It can be!

    • @13yearsaprepperr.jtilbury.51
      @13yearsaprepperr.jtilbury.51 2 ปีที่แล้ว

      I take the handle apart it takes 30 seconds , Its a lot better
      Rob
      NSW
      Australia

    • @stihlhead3338
      @stihlhead3338 2 ปีที่แล้ว

      It's like watching a gorilla do open heart surgery! Just take the cover off, it only takes 30 seconds.

    • @BillsGarageWorks
      @BillsGarageWorks 2 ปีที่แล้ว

      Why did you replace the impulse line? I have a 042 But I just put a carb kit in and fuel is leaking out from somewhere and making the saw stall and flood could this be why or is it most likely maybe the needle and seat?

  • @paulmysliborski4832
    @paulmysliborski4832 2 ปีที่แล้ว

    Thank you for this vid. :)
    Do you have a parts link?