Thank you for the comment, apologies for the late response, a E1 error is PC board related, you have to take it have it repaired at your nearest reseller or get a installer to take it in for repair
Hello, I just adjusted my door because the gap was alittle to big on the floor... But now I get the P error when trying to open with the remote button... I then tried to reprogram the remote, I go to r and then b, when I press on my remote it give a number 2 and not number 1 which ma leans successful, can you let me know why that is please?
Thank you for the comment, you can only adjust the door by doing the completed limit setup, it will flash P until you complete the limit set and the remotes will also only work once the motor confirms limit setup completed
Hi Sir I have error P.Aftet resetting or programming instead of going to exit at the end it goes back to P and does not longer accepts remote after wards.I don't know what to do now
Thank you for the comment, after it does the limit setup it will go back to flashing P, then you press exit 2x. It will then go to standby mode and that is when you test it with the remote. Where are you getting stuck?
Thank you for the comment Jacob, please take it to the nearest re-seller to have it sent to NICE SA for repair, it's a PCB issue that has to be fixed, or purchase a new board
![[Gegagedigedagedago] NEW Help Gegagedigedagedago Nugget escape from Nikocado Avocado Challenge](http://i.ytimg.com/vi/hJWnwRC2Fz8/mqdefault.jpg)
Thank you man, I really thought I broke my dad's garage door. I'm subscribing now
@SenzeloMabaso-rt7jn thank you for the comment, much appreciated
@@nicksandtrickssa thank you so much for the fix. Truly appreciate it 🙏
Hello Nick. Please assist. I'm getting a 3/1 error code after my limit set up. What could be the problem?
Thank you for the comment, apologies for the late response, a E1 error is PC board related, you have to take it have it repaired at your nearest reseller or get a installer to take it in for repair
Thanks a lot!!
You're welcome!
Hello, I just adjusted my door because the gap was alittle to big on the floor... But now I get the P error when trying to open with the remote button... I then tried to reprogram the remote, I go to r and then b, when I press on my remote it give a number 2 and not number 1 which ma leans successful, can you let me know why that is please?
Thank you for the comment, you can only adjust the door by doing the completed limit setup, it will flash P until you complete the limit set and the remotes will also only work once the motor confirms limit setup completed
Thank you so much... It is working now after your comment... Much appreciated
@@azizarichards1002 no problem, a like and sub to the Chanel would be greatly appreciated
Hey Man do you know how to stop the beeping when the power goes off?
Thank you for the comment Byron, unfortunately there is only 1way, sperglue in the speaker
Thanks for the reply, yeah been looking everywhere to try figure out how to do it, would disconnecting the battery help? @@nicksandtrickssa
Like I said, only 1 way
Hi Sir I have error P.Aftet resetting or programming instead of going to exit at the end it goes back to P and does not longer accepts remote after wards.I don't know what to do now
Thank you for the comment, after it does the limit setup it will go back to flashing P, then you press exit 2x.
It will then go to standby mode and that is when you test it with the remote.
Where are you getting stuck?
After I set the limits, Im getting a flashing 2 and 3?
Thank you for the comment, flashing 2 and 3 is not something I have come across, u certain that's what it's doing, it's not a E and a number maybe?
@nicksandtricks1849 Apologies it displays E2 when trying to sent the limit.
I believe E2 is an obstruction during the setup process, clear the obstruction to continue... Have a look at the door for physical issues
Hi sir. I have error code E1 displayed on my garage motor when I try to open the garage.
Thank you for the comment Jacob, please take it to the nearest re-seller to have it sent to NICE SA for repair, it's a PCB issue that has to be fixed, or purchase a new board