DC Blue Advanced Garage Door motor setup
ฝัง
- เผยแพร่เมื่อ 21 ก.ค. 2024
- In this episode, we go through the Limit setup and remote setup on a ET DC Blue Advanced Garage door motor
Channel sponsors:-
Rsec Security Equipment Center
www.rsec.co.za
/ rsecequipmentcentre
/ rsecsecurity
Music:- Gemini - Halfcool (no copyright)
Link to Products
rsec.co.za/product/dc-blue-ad...
00:00 Intro
00:17 Limit Setup
02:04 Receiver programming
03:27 Quick Learn
03:44 Outro
Please comment, like, share and subscribe to the channel
Follow me on Instagram:- @Nicks_nd_Tricks
Follow me on Facebook:- / nicksandtricks - วิทยาศาสตร์และเทคโนโลยี
Very helpful thanks. Never knew about the light function before this video.
Thank you for the comment, good to know my video is informative
Good day,
Thanks, the video really helped set up the garage motor.
Thank you for the comment, much appreciated
Thank you for instructions easy to follow.
Apologies for the late response, thank you so much for the comment.
Thanks for the video, it really helped me.
I don’t know if you have ever encountered this issue, but garage door won’t stay open or closed. It’s been opening halfway then closes again, repeatedly closing and opening, had to disconnect the battery and power for it to stop. Any ideas on what the issue is
Thank you for the comment, if you have a third party receiver, those normally causes that type of issue if not then your door might be going into collision
Hey boet, what a very informative video! Thank you. Can this motor be used with a baterry backup?
Thank you for the comment Lloyd, yes there should be a bracket at the top of the motor where a 24V3.5Ah battery sits. A sub to the channel would be great, thanx
Very good video 10/10
Thank you for the comment
Hey thanks for a video, my problem is while setting limit up doesn't work and that where i am stucked now
At which part does it fail
Thanks , helped me
Please like and sub, much appreciated
Thank you bro!!
Thank you for your comment, a like and sub would be great
Great video thanks. How does one remove the beeping sounds as the motor is opening and closing, very annoying and loud but can’t seem to find instructions for this anywhere
Thank you for the comment, not too sure which beeping you are referring too, is this when there is no AC or all the time?
It's flashing E & I after opening, and I think it's beeping from that warning message. I don't think we have a sensor (tilt garage door) and it does this when power is connected, so all the time once the garage is opened fully. @@nicksandtrickssa
Apologies for the late response, and E1 error is a pcb related issue, motor head to be taken to a service center.
Hi Nick, please assist if I press close on the remote it will go down and as soon as it reaches the bottom it will automatically go up again and open. I think the setting went out but don't know how to reprogramme it.
Thank you for the comment, you have to set the limits again, was the door Interrupted at any point before it does this?
Hey. Just watched your video. I've got the DC Advanced. I cannot add extra remote. All my remotes just beeps when I press the button. And it is stuck on b.
Also when I want to do the quick programming holding the up button does nothing on my motor.
I've tried switching it completely off and on again
Still stuck on b
Thank you for the comment David, if your looking at it right side up and its a small "b"
it means the beams are active, if you do not have beams, do the following...
press and hold set, scroll up to capital "A"
press set to confirm
scroll down to number 0 and press set to confirm
it will take you back to small "p"
now scroll up to small "b"
scroll down to number 0 and press set to confirm
then press exit and exit again, you should now be instandby mode
to half 11 on the screen, press the remote and see if the door runs
we will address the adding of remotes after
Thank you brother.
Thank you for the comment, a like and sub would be great
Thanks boet!
Thank you for the comment, much appreciated 👍
How do you clear out previous remotes if you no longer have them? Thanks
Thank you for the comment, follow this video... th-cam.com/video/b6h0_9kLisU/w-d-xo.html
Excellent video. Well done, helped me out after servicing garage motor to realign chain catch.
Thank you for the comment Werner, unfortunately I don't do the door mechanics, so I'm unable to assist
Hi. My chain got stuck, and i had to remove and return the motor to loosen the chain. Now my remote doesn't want to work. I tried setting the limits and did everything according to your video. The only difference is that theres an intermittent beep at the end after the unit closes itself. I see in the video that your system only beeps once and goes to P on display. I get an E 1 error. How do i fix that
Thank you for the comment, E1 error is encoder error/motor fuse blown, if the motor moves even a little then it's a PCB issue and you would have to send it away for repair
How do I check the fuse ? I don't want to get a technician out if I can replace a fuse. How do I do it ? Many thanks for your other videos,got it working initially, but now got E1 code and won't move.
Apologies for late response, the fuse is at the top by the battery, 8 out of 10 motors I get with E1 has faulty relays and PCB needs updated software, the other 2 is an encoder failure on the inner motor or both failing
Trying to program the new m otor it doesn't ngo up instead it shows 2E and keeps on beeping
Please help
Thank you for the comment, E2 is a physical obstruction, fix the obstruction first then attempt the setup again
Hello, i need help with the garage motor it have display error code "b"
thank you for the comment, please see
th-cam.com/video/8fwuxNGJt7g/w-d-xo.html
it will help you with the error
Hi Nick. Thanks for the video. I set the limit and added anew receiver successfully.
Problem: The Garage door opens but when i try closing, it beeps and shows a "b". What could be the issue?
No worries boet. I sorted the problem for my mum thanks. The A value needed to be set to 0. Great video.
@@Yo_MaMa_69_420 no problem, there is a section where I go through the Auto-close yes. A like and sub would be appreciated
Hi Rajesh, watch this...
th-cam.com/video/W56yUv6ZB_g/w-d-xo.html
But do the opposite, set values to 0.
Time 00:09
@@nicksandtrickssa okay thanks. I subscribed.
I'm experiencing the same problem 😕 can you please assist me, I did set the a value to 0 😱
Hey the remote is working but whenever i press open on my remote it say a "P" and sometimes says "3" then straight after a "1" Please help
Thank you for the comment, can you please take a short video an mail me on technical@rsec.co.za
hey sir when it shows the 2 lines im suppose to press the up button so it can show me the "b" but it doesnt wanna work
Thank you for the comment, hold the set button, to go into programming
@@nicksandtrickssa so i did that
i programmed "b" to the blue button
and it showed me "1"
now when i get back to standby
when i press the blue button
it just shows me "p" and it starts beeping
@@user-md5xx8up5j you have to complete the setup, before you can use the remote, do all the steps as it is in the video
@@nicksandtrickssa i just followed the instructions and im where you say i should close the door on the blue thingy
so when the door closes
it flashes "E" and "1"
@@user-md5xx8up5j a E1 error is a faulty PCB, motor needs to go in for repair
Howzit
Im getting a 3 1 error
What do i do?
Thank you for the comment, an E1 error or a PCB error, take the PCB in for repair
Thanks for the video. Just wished there was no music in the background while you doing the instructions
Thank you for the comment Jaden, anything that you missed? There is smaller videos which the full video consists of, maybe those will suit you better?
Wot is it if the do dnt close or open
Thank you for your comment Carl, it depends on the error, or if you have a standalone receiver
great video. i keep getting E1 error. how do i reset the device?
Thank you for your comment Llewelyn, unfortunately, E1 is either your encoder or PCB that cannot read the encoder, so you have to take it to a repair center, Rsec Security Equipment Center in Bergvliet, or an installer can do it for you.
@@nicksandtrickssa thanks for the reply. took of the cover. looks like some burn on the white 3 pin plug where it says encoder on the pcb. the resistor next to it also looks fried
@@llewelynklaase7896 , that could be the source of the E1, also the resistor bottom left is for the battery, mb door too heavy, if wooden door, that can be cause as well
Just asking...also getting a E1 code...how do I get the cover off to see if something is burnt.
Thank you for the comment Mark, at the top, where the battery is, there is 4 phillip head screws, be carefull as the cover will drop when you loosen the last screw.
Also note that 8 out of my last 10 repairs was faulty replays and software that was needed to fix the E1 the other 2 was faulty inner motors or both issues
Please tell me how to decommision
Please tell me how to decommision my remote
Thank you for the comment. Press and hold set, go up to r, press set, go to b, press set, go to C, press set, press and hold the remote, 0 is clear complete, 3 is unsuccessful, try again
Thanks now i can set the lighter but second one when i press the button it gives me a 2 instead of 1
Thank you for the comment, 1 is for successful learn, 2 means a button is already learnt, and 3 is either no transition or too long
How to Open; During LoadShedding?
Thank you for the comment Dreshni, there should be a red string hanging from the middle of the draw bar, pull it and you can manually open and close the door, be careful tho
Why is there not a video of how to install the motor from start to finish with track and all.
Thank you for the comment Bobby, problem with that is every site is different and every gate is different, and I gues noone in the industry want you to do it by yourself... If you get hold of a manual it really tells you exactly what to do tho.
@@nicksandtrickssa 👍
When adding a new remote it does not show 1, instead it beeps and then displays a 3
Thank you for the comment, try and do it faster, 3 means no transmitter detected
Will give it a try and let you know. Thanks
Tried.. Still getting the same thing. Funny thing is. The remote was programmed before but then stopped working
So the thing is... These thing don't just stop working, if you think back to when it stopped you will find the culprit that damaged the receiver, you will have to purchase a single Chanel receiver and program to it, please also check if the PCB is still ok, nothing melted or blown
I assume the receiver is fine because other remotes are working fine
My garage door keeps bleeping and won’t close or open . Saying a P
Can’t figure out what it means
Good day Letty, the P indicates it is in program mode, if you press exit does it go away? The door will not function in this mode
@@nicksandtrickssa thank you what’s some setting on B I had to set back to zero
That is correct, nice to see you all sorted, please like share and subscribe
it was actually little b you saw, which is the safety beams
Hi Nick's and Tricks... Mine is also showing "b" and the other buttons don't work... How do I exit? When I press the remote is beeps a couple of times then stops and nothing happens
What if there is 2 lines and don't want to open
Thank you for the comment, if it's 2 half lines, it's in standby, if all the remotes does nothing as well as the buttons on the display, then PCB faulty...
If you give me more info I can assist
Hello sir my garage door when close will open but when pressing the bottom again to close it doesn't close instead it shows a 'b' sign and the light goes on
So I also tried the little r setting and instead of showing 1 to confirm it shows 2 what does that mean?
Good day Unathi, thank you for your comment. U have to disable the safety beams and Auto-close. Check out my video on enabling those settings and instead on 1, turn to 0.
th-cam.com/video/W56yUv6ZB_g/w-d-xo.html
1 means paired successfully - 2 means remote already on receiver - 3 means that no transmission was received - F means receiver is full
Thanks for the advice. Maybe turn the background music down. You can not hear the instruments properly
Thank you for the comment Andre, hope it was helpful tho?
Ive done 'L' function.. the door opens but does not close...need help 😩
Thank you for the comment Joe, is this during the limit setup? Does it give a error?
@@nicksandtrickssa nope. This happens once the remote is coded. It reads 1. Once you exit and test the remote, it opens the door but does close it. I'm close to you store in bergvliet and will pop in to seek help..🤣. If , however, I'm doing something wrong please advise.
@@joeadams4014 is there no error, like little b on the screen?
@@nicksandtrickssa yes there is..
Please see th-cam.com/users/shortsYbRfYgDtvsM?feature=share
The chain is stuck showing E2
Thank you for the comment, have you resolved this yet?
Hello sir mi garage when I'm opening it's opening bt when I'm closing it doesn't close its show me b
Thank you for your comment, u have to turn the beam off as well as autoclose, unless you have beams
th-cam.com/video/W56yUv6ZB_g/w-d-xo.html
Use this video and instead of turning it on you will turn it off