Hi Nick. Thanks for the video. I set the limits successfully but when I try setting the "b" button for receiver, the lid displays a "2". Could you maybe help me understand what to do?
Thank you for the comment Rajesh, does your remote not work? Please see... th-cam.com/video/b6h0_9kLisU/w-d-xo.html Will help with remote setup. 1is successful add, 2is transmitter already successfully added, 3is no transmission received
Thank you for this video 🙏🏻 has helped me a lot with programming my remotes as well as working with the motor. I have a question that I’m hoping you can help me with. My garage door is closing and then sometimes 1/2 or 3/4 way down it stops closing, beeps once and then opens again. If I stop it opening and close it again quick enough it will close fully. How can I fix this?
@@oldboneybird thank you for the comment, it sounds like there is a physical door issue, you can increase the force on the motor to get past the issue, is it related to the weather? Do you have a wooden door?
@@oldboneybird change the force settings for now and change it back once the door has settled again, I have a video on settings force as well, have a look
@@mdt6101 thank you for the comment, E2 is a physical obstruction, E3 I'm not too sure about, but if you fix the physical obstruction the door should be fine Check in the track
@ToMakeAMonster thank you for the comment, when you look up at the motor the battery is ontop of the motor, you will find a female battery connector terminal to plug new battery terminals into
Thank you for the comment, short answer is no, but you can try changing the force settings, but be careful, the higher the force the higher the resistance needed to stop the door...
Thank you for the comment, if none of the remotes is not working, and it is NICE remotes you will have to get a standalone receiver to get it to work, could be issue with the onboard receiver, try and reset the receiver and see if it works
Thank you for the comment, I tried getting it from NICE but it's not possible to get, intellectual property and all, you will have to pay for them to flash your card
Thank you for your comment Zack, 3 means no transmitter received, took too long. Is the remote on the correct set? Press and hold remote for 25seconds till it pulses then let go and try again
@@nicksandtrickssa thanks for the super fast reply. I held it now for 25 seconds until it flashed and tried again. Still flashed 3. It's strange because it apparently worked 2 weeks ago before we moved in.
Thank you for your comment Luenda, the DC Blue Advanced has built in LED lights, the DC Blue Digital is a 24V DC light bulb, not sure of the DC Blue Plus
Thank you for the comment, I'm busy with that video still should be completed soon Go into programming, go to small b, press set, set to 0, press set, go to Capital A, set to 0, press set, clear clear
![ทุกครั้งที่หลับตา (Lucid Dream) - AYLA's [ Official MV ]](http://i.ytimg.com/vi/4i1OBAQyv58/mqdefault.jpg)
You saved my day today 😊
@@isaiahmoyo6177 glad I could help
Really helpful Nick, great video and very well explained, thank you so much
@@craigburns6447 thank you for the comment, much appreciated
Hi Nick , do you perhaps have a video on the physical installation maybe?
@craigburns6447 unfortunately not, I do repairs, not installs, only work with the electronics on the motor
Thank you the video helped a lot and it was very easy.
Thank you for your comment, please like and sub for more
Thanks. Helpful
Thank you for the comment, much appreciated, glad I could help
Hi Nick. Thanks for the video. I set the limits successfully but when I try setting the "b" button for receiver, the lid displays a "2". Could you maybe help me understand what to do?
Thank you for the comment Rajesh, does your remote not work? Please see...
th-cam.com/video/b6h0_9kLisU/w-d-xo.html
Will help with remote setup. 1is successful add, 2is transmitter already successfully added, 3is no transmission received
@@nicksandtrickssa It works now. I cleared the memory with E and added it back with a "1".
@@rajeshreemack4666 well done, a like and sub would be appreciated
Thank you for this video 🙏🏻 has helped me a lot with programming my remotes as well as working with the motor.
I have a question that I’m hoping you can help me with. My garage door is closing and then sometimes 1/2 or 3/4 way down it stops closing, beeps once and then opens again. If I stop it opening and close it again quick enough it will close fully. How can I fix this?
@@oldboneybird thank you for the comment, it sounds like there is a physical door issue, you can increase the force on the motor to get past the issue, is it related to the weather? Do you have a wooden door?
@@nicksandtrickssa that was my thoughts, yes it’s a wooden door and it only started happening now in winter time..
@@oldboneybird change the force settings for now and change it back once the door has settled again, I have a video on settings force as well, have a look
@@nicksandtrickssa thank you 🙏🏻 I will try do that then
What if it shows a flashing E, 2, 3? When you try to open the door?
@@mdt6101 thank you for the comment, E2 is a physical obstruction, E3 I'm not too sure about, but if you fix the physical obstruction the door should be fine
Check in the track
Hello how do I replace the back up battery for the same garage door motor ?
@ToMakeAMonster thank you for the comment, when you look up at the motor the battery is ontop of the motor, you will find a female battery connector terminal to plug new battery terminals into
Is there a way to make the door open and close faster
Thank you for the comment, short answer is no, but you can try changing the force settings, but be careful, the higher the force the higher the resistance needed to stop the door...
Very helpful
Thank you for the comment Peter. Much appreciated, a like and sub would be appreciated 👍
I’m unable to set any of my 3 remotes it just displays 3 and I’m pressing quick enough it used to all work before when I set it
Thank you for the comment, if none of the remotes is not working, and it is NICE remotes you will have to get a standalone receiver to get it to work, could be issue with the onboard receiver, try and reset the receiver and see if it works
@@nicksandtrickssa how do I rest the receiver?
th-cam.com/video/b6h0_9kLisU/w-d-xo.html
2:35
Very helpful 👌
Thank you for your comment Mutasim, a sub to the Chanel would be great
Hi do you have the EPROM files for the dc blue advance mine need to be reprogrammed
Thank you for the comment, I tried getting it from NICE but it's not possible to get, intellectual property and all, you will have to pay for them to flash your card
Okay thanks will have to hear what they say
My remote works fine, but when I try to add my wife's remote, it's flashes 3 instead of 1. Any advice there?
Thank you for your comment Zack, 3 means no transmitter received, took too long. Is the remote on the correct set? Press and hold remote for 25seconds till it pulses then let go and try again
@@nicksandtrickssa thanks for the super fast reply. I held it now for 25 seconds until it flashed and tried again. Still flashed 3. It's strange because it apparently worked 2 weeks ago before we moved in.
If it is the only remote not working then it's the remote that's the issue, try and reset the receiver and then try again
Quantos voltes tem a lâmpada de cortesia dc blue
Thank you for your comment Luenda, the DC Blue Advanced has built in LED lights, the DC Blue Digital is a 24V DC light bulb, not sure of the DC Blue Plus
Im unable to program remote. It doesn't show 1, it shows 2
Thank you for the comment, the number 2 indicates a remote which is already in memory
Hi. My garage motor is stuck on b. I don't have sensors. How do I get rid of the b.
Thank you for the comment, I'm busy with that video still should be completed soon
Go into programming, go to small b, press set, set to 0, press set, go to Capital A, set to 0, press set, clear clear
Tks. It just keeps going back to small b.
th-cam.com/video/8fwuxNGJt7g/w-d-xo.html
done all yhe video has told me. i get 1 but when i use the button i get 5 beeps
Thank you for the comment, on the motor screen, it should give you a error code, what is it?
I managed to get the button to open. But after opening, it shows B and doesn’t close again after pressing the programmed button again
Please check, th-cam.com/video/W56yUv6ZB_g/w-d-xo.html
It shows how to enable beams and autoclose, you have to do the opposite, set them to 0
@@nicksandtrickssa thank you. But now when I press the open button it shows a P
Make sure to go to little b and set to 0, then go to big A and set it to 0 as well
@@nicksandtrickssa hi! I have done that. Still the same.
Send me pics of the display to technical@rsec.co.za please
Installation motor
Hi Kagiso, instillation is not my strong suite, I'm more on the setup and troubleshooting side, the mechanics not so much, apologies