The gauge in this video is NOT an X series gauge. My gauge is a classic gauge. I believe that is for the new version of the AEM requires the Brown wire to be wired in as well. I have heard it goes to Pin D21 but I cannot confirm 100% as I have not tested. [30-4110] Classic gauge only has: Red - 12V Power Black - Ground White - 0-5v Output Blue - Serial Output [30-0300] The X series has: Red - 12V Power Black - Ground Green/Black - AEMnet- /CANL White/Black - AEMnet+ / CANH Blue - Serial / RS-232 Output White - 0-5v Output Positive Brown - 0-5v Output Negative Hope this helps!!
I like that. "We are not professionals. We do what we can, with what we have, to make our projects work." Amen. Same here, but i never heard it put better than that.
My version does not have the brown wire, I believe that is for the new version of the AEM. I have not worked with them before but it does seem that it does need to have the brown routed as well. Mine only had: Red Black White Blue
My version does not have the brown wire, I believe that is for the new version of the AEM. I have not worked with them before but it does seem that it does need to have the brown routed as well. Mine only had: Red Black White Blue
Not needed for this type of install. The white one is the only one required. The blue wire is for Serial Output. The white wire is for 0-5v signal. Any questions lmk!
You may be able to do it without the gauge but I know AEM has the output directly from the gauge. You may be able to solder it in but I do not know the workflow to do so.
Nayz bro.. no bullshit, straight to the point, precise instructions, video and editing on point. Deserves a "subscribe'. 😉 Been having trouble getting proper info on wideband sensors. Thanks for the vid.
Yeah my s300 was upset because originally I selected the p04 setting. I couldn’t for the life of me figure out how to show 0-5v on s300. Well that was the problem. When I switched to the p0 setting it corrected that.
Hi! That is the same harness I used for my setup as well since mine is a 2000. It might vary slightly but for sure it won’t affect you since you’re OBD2B👍🏻 Just make sure you are wiring in the correct signal wire and you should be good
![[TH] 2024 PMSL SEA W2D5 | Fall | พลาดวันนี้ จะต้องเสียใจ](http://i.ytimg.com/vi/A5-Cuo12p6A/mqdefault.jpg)
The gauge in this video is NOT an X series gauge. My gauge is a classic gauge.
I believe that is for the new version of the AEM requires the Brown wire to be wired in as well. I have heard it goes to Pin D21 but I cannot confirm 100% as I have not tested.
[30-4110] Classic gauge only has:
Red - 12V Power
Black - Ground
White - 0-5v Output
Blue - Serial Output
[30-0300] The X series has:
Red - 12V Power
Black - Ground
Green/Black - AEMnet- /CANL
White/Black - AEMnet+ / CANH
Blue - Serial / RS-232 Output
White - 0-5v Output Positive
Brown - 0-5v Output Negative
Hope this helps!!
I like that. "We are not professionals. We do what we can, with what we have, to make our projects work." Amen. Same here, but i never heard it put better than that.
Hell yeah!🙌🏼🙌🏼😂
took me forever to find out if I could replace the factory o2 with my wideband. Thanks for the help
Finally someone that knows how to show and explain how it’s done thanks again bro literally did it in 30 min thanks to you
Happy to help 🙌🏽🔥
saved my life. just got my first z6 build and all it needs to run is a afr and boost gauge. thanks to you i’ll get it done tomorrow !!
Awesome to hear!! Hope this helped out🙌🏼🙌🏼
Good luck with the Z6! Hella setup
@@CJBuiltshe runs after today! thanks again bro!!!
@@waltervreeland9147 Love to see it!
Very glad this could help!
thx working good on my old p28 95 si
you CUT the freaking wire cody LMAO!! great vid tho helped me with all the confusion
LMAOOOOO
Glad I can be of help!
Was confused cause if you use the numbers on the plugs it’s totally different got it now thanks. bro.
Which part was confusing for you?
Would love to know to see how I can simplify it or correct it in the future
Gracias por el contenido saludo 🔥💪🏽🇵🇷🙏🏼❤️
Muchas gracias!!🙌🏽🙌🏽
god tier video thank you
I appreciate the support brotha!! Glad it helped out 🙌🏽🙌🏽
Thank you bro🙏🏿 really thank you
Anytime! Glad this video can help 🙌🏽🙌🏽🙌🏽
Do you have to connect the brown wire on the gauge to d21??
My version does not have the brown wire, I believe that is for the new version of the AEM. I have not worked with them before but it does seem that it does need to have the brown routed as well.
Mine only had:
Red
Black
White
Blue
Nice videos brother but i heard you have to wire the brown wire to d21?
My version does not have the brown wire, I believe that is for the new version of the AEM. I have not worked with them before but it does seem that it does need to have the brown routed as well.
Mine only had:
Red
Black
White
Blue
@@CJBuiltwhere did the blue go
Where does the blue wire go?
Not needed for this type of install.
The white one is the only one required.
The blue wire is for Serial Output.
The white wire is for 0-5v signal.
Any questions lmk!
hi, can i conect the sensor without de gauge?
You may be able to do it without the gauge but I know AEM has the output directly from the gauge.
You may be able to solder it in but I do not know the workflow to do so.
Nayz bro.. no bullshit, straight to the point, precise instructions, video and editing on point.
Deserves a "subscribe'. 😉
Been having trouble getting proper info on wideband sensors.
Thanks for the vid.
Glad it can help!
I appreciate the sub and the positive feedback!
Where wire 4 going from 02senzor
Which wire are you speaking of? Let me know which gauge you have and what color wire 🙌🏼
What setting did you have the gauge on? P0 like it comes or did you switch it to p04?
P0 still, have not touched the settings.
Yeah my s300 was upset because originally I selected the p04 setting. I couldn’t for the life of me figure out how to show 0-5v on s300. Well that was the problem. When I switched to the p0 setting it corrected that.
Good to know! Thanks for the feedback!
Is yours an X series or the older style?
Bro, aside from the AEM wideband, is the PLX or MTX-L PLUS also applicable?
I believe it is, I do not see why not.
Only difference I would see is the output wire may be a different color on the other gauges
Hello! I have a p28 for my 00’ d16y8 with an OBD2B jumper harness. Does the pin out differ from OBD2A?
Hi! That is the same harness I used for my setup as well since mine is a 2000.
It might vary slightly but for sure it won’t affect you since you’re OBD2B👍🏻
Just make sure you are wiring in the correct signal wire and you should be good
@@CJBuilt Cool! And we count from the ECU side correct?
Yes. Verify of course using the diagram but it’s the plug while it’s facing the ecu
Sub'd, Liked & Shared 🙏🏻👊🏻
Thanks for the support!
What program are you using?
Honda tuning suite
Was this the aem x series ?
Hi! No this was not an X series.
Check the manual for the wire on the X series for output. It may be different than mine