EVO Transmission Installation - How to Install a EVO Trans // BoostedFilms

Interested in investing and getting a free stock? Use my Robinhood referral link and help us both!
referral.robinhood.com/paule556
Transmission Removal: www.youtube.com/watch?v=LGi_c...
Rear main seal change: www.youtube.com/watch?v=3dJOC...
ACT monoloc collar: www.youtube.com/watch?v=OGMxm...
Facebook: / boostedfilms
Instagram: / boostedfilm
Snapchat: boostedfilms
Disclaimer: This video is for entertainment purposes only! Perform anything you see in this video at your own risk. Due to factors beyond the control of this video creator, I cannot guarantee against improper use or unauthorized modifications of this information. Boosted Films assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. I recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Boosted Films, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Boosted Films.

[@thecaretaker8934]

to everyone who owns an evo 7 dont be scared to work on it yourself its easy once you actually go for it, i just change my water pump and did all the timing myself with no prior experience just youtube haha

[@marcelwengerter8442]

Lol I was sitting back this afternoon thinking about how I was going to approach the reinstall on the evo x. I'm doing the job by myself as well. I found your video and it was pretty much step by step the same as I had pictured in my mind. I guess great mind truly do think alike...lol. some people make things harder than they need to be. Work smarter than harder.

[@YouGotThrilled]

Thanks for this video, just picked up an evo 8. Earned a sub!

[@BoostedFilms]

@@YouGotThrilled congrats on the evo pickup! Lots more evo info on my site, BoostedFilms.com

[@jaker2042]

Again thanks for the videos! I have the mr 6 speed was going to try doing this my self, need new clutch. But that's a big job

[@phelicks1579]

Why does your clutch fork move so effortlessly by hand ..must be nice lol

[@peterush8709]

Another great how-to. :-)

[@Archie106TV]

Thanks again

[@TheLordofShell]

Just did this last week and it really is brutal. 1 jack under the oil pan and two under the transmission trying to wedge it in with a prybar...
Next time I'm probably just going to drop the subframe I think that will save a lot of time and anger.

[@BoostedFilms]

Dropping the sub frame adds in issues with the steering rack, that's why i didn't touch it.

[@phelicks1579]

I was thinking the same thing..took two days to drop my transmission with one jack by myself

[@LancerEvo97]

great video man, i just got my evo all done and tuned with my new exedy twin and fp red and made 430 whp on the dyno jet, very happy all that hard work paid off as im sure yours will too, my evo trans install was also on my garage floor and i didnt have a cherry picker, i just had a harbor freight trans jack and nearly killed myself attempting it on my own , then i had 2 other people help and we got her done, i had the same issue with not being able to fully mate the trans to the block before starting in some bolts but i just did the same as you did and guided them the rest of the way in, youre completely right this job on the ground sucks ass, i sure as hell wouldnt do it again unless im able to perform it on a lift, my only concern is how youre going to get that rear mount bracket back on, i was able to get my trans out and in with it on, so i feel you may have created another obstacle for yourself, just and opinion from my own personal experience, i admire all your videos, i have used them as a tool for a lot of my work i performed on my evo 9, expecially the ones with the timing belt and cams, you definetly go over some really important details that can make or break you, eventually id like to make a channel with good informative videos like yours, awesome work man, keep it up

[@BoostedFilms]

an FP red would be sweet! Sounds like a nice set-up. I already installed the rear motor mount and it went fine. Took about 30 minutes. But yes, i probably should have bolt the rear motor mount plate back on the trans before putting it up in place but i never though about it.

[@LancerEvo97]

Boosted Films yea I know the evo 9 turbos make great power too, i was at 376 whp on my stock turbo on pump gas before the oil seals went , that’s why I upgraded my fp red which made me have to upgrade my stock clutch to the exedey twin, I’m still on the stock manifold just because I didn’t feel like spending another grand lol, the fp red ball bearing is expensive but so far i feel like I got my money’s worth , great spool up, and sounds amazing , and my power band is nice and smooth, all things that a good turbo should do👍

[@1989rrichard]

Awesome video brother ....I have done this about 6 times already in the ground 😂😂each time I do it quicker ...

[@EDDYPRIME]

Your clutch is suffering to much))))

[@ophv1998]

I was wondering about that throw out bearing! No problem to get it out, and it went back inn smoothly, the “click” came and I shoved the throw out bearing all the way from the left to the right (standing in front of the car looking under the hood) now mine just don’t won’t to go back now and is “lock” more in place than it was before removal. Is this normal? Should it go back with the slave cylinder on? Didn’t manage that with hands power tho!
It would be nice if you showed how the throw out bearing was moving after the “click” mine was stuck in the middle only going towards the clutch not all the way out 🤔

[@dontmatter1335]

So I have an evo x and my clutch fork is on the left side and has play (I can move it with one finger) how do I move the fork towards the middle ?

[@jovanymendez8018]

Hey hope your day is good, wondering what are your thoughts on this, @9:50 I popped the tob in and after I attached the sc I'll push the clutch pedal and the slave cylinder will pop back out

[@seanhatch4425]

How long did this clutch last?

[@monglor6978]

How do you put the shaft back into the trans/tcase? Does it simply slide in with the help of a rubber mallet?

[@BoostedFilms]

Yup. That works. Or use a slide hammer to tap it back in.

[@davewallace5008]

I learned the hard way and now remove the radiator :/ It is so easy to damage it trying to install the g/b. Two years on and the thrust bearing has been ripped apart, so it's under the car again :(

[@phelicks1579]

im having an issue with getting my throw out bearing to snap back into my wave clip..any suggestions? it just wont snap back in

[@jovanymendez8018]

How did you get past this?

[@phelicks1579]

@@jovanymendez8018 my issue was really just the clip being so worn and me trying to reuse it...i ordered a new one and it snapped in and never came back out

[@nextchapter2343]

thanks 2020

[@zeroiscool14]

1st!

[@LancerEvo97]

😂

[@twincamdave69]

it literally took me 4 -5 hour to put it back with 2 hoist from the ground... terrible :D

[@LancerEvo97]

Lol ting