Whirlpool Cabrio Maytag Bravos Washer Bearing Removal and Install - Tips & Tricksll Tips and Tricks

Whirlpool bearing replacement tips and tricks. A bearing tool kit to assist in the repairing Whirlpool Cabrio and Maytag Bravos washers that utilize the first generation stator motor.
Tub Removal with Car Jack:
• Cabrio Washer Tub remo...
More About BundysGarage:
goo.gl/qv3Wzc
Questions, Comments, Concerns:
[e-mail]
Twitter:
/ bundysgarage
@bundysgarage
On The Web:
www.bundysgarage.com
Music by Randall Kent: As seen on NCIS
• Randall Kent - Going H...
All Rights Reserved 2017
© Copyright 2017
Bundys Garage
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: [e-mail]
DISCLAIMER - DISCLAIMER - DISCLAIMER
Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.

[@arthurfricchione8119]

I just got rid of mine. 5 yrs old and a piece of junk. My wife hated it. Sounded terrible and the noise was unreal. Bought a speed queen all mechanical all metal gears and transmission. NO PLASTIC NO ELECTRONICS. GOOD LUCK

[@bundysgarage]

Yeah my wife hate it too. She says it does not clean as well as the one we got rid of. We were all excited to get it 8 years ago and after a week of using the new one, we wish we hadn't sold our old ones. If I can get another 5 years from it I'll be happy.

[@arthurfricchione8119]

Been there done that she would not let me fix it. Had to send the parts back. Have to keep her happy. GOOD LUCK

[@bundysgarage]

Thanks. I know the struggle brother. Happy Wife, Happy Life!

[@WilliamHollinger2019]

It have been happened to my and we are in progress of repairing.

[@claytonjbeckiii3429]

I'm sure this will be helpful to many. I had to replace the bearing in my 90's era Neptune (the one that sank Maytag). There was only one guy on the Internet helping people. He invented a puller and even rented it out for a reasonable price. Took whaling on it for an hour with a 5 lb sledge but I got it. Maytag repair wanted $600 to repair, I did it for about 10% of that and had the satisfaction. I hope your video will help many, again thanks for putting this ans your other helpful videos out! :-)

[@doctorfeinstone6524]

If you're referring to the tony tool, it's price is anything but reasonable

[@5jjt]

If you take a small metal pick, you can remove the bearing's rubber seal and pack the bearing with some better grease.

[@bundysgarage]

Thx for the tip!

[@robertscott8227]

i bought my parts from an ebay site . i bought tools and bearing shaft kit for 129.00 they come all together as one package . i have a suggestion on cleaning out bearing surfaces on the the washer side use brake clearer but remember this stuff is flammable so use adequate ventilation . i also used a small amount of Loctite on the nut that is on the bottom lower nut on the shaft , it prob isn't a big deal but the nut on my washer was loose ,this may be part of the seal failure issue . its not a real complicated repair but takes a little time .

[@bundysgarage]

Good info. Check this out:
th-cam.com/video/Hhkj8zQmL6I/w-d-xo.html

[@israelmendez2259]

It was showing sd on my Whirlpool Cabrio so I replaced the bearings and a new shaft now sd code is gone but now showing code ul could it be the suspension rods?

[@WilliamHollinger2019]

You could over fill your washer with load if it still have the ul then the suspension then.

[@ScantPear]

Cabrio not cubreo

[@andrewdugan6705]

Pronounced CAB-reo, not kuh-BRI-o
Sorry, but this drives me crazy. Good informative video though. Thanks.

[@tellsthetruth894]

This video is unnecessary.