Solved my rotor issue. On my washer there is a heavy duty magnet which made it require more of a tug to get the rotor off. Most of the work is done. Just waiting 24 hours for the glue to dry. Great video! I really enjoy doing projects, especially when my wife doesn’t think I’m up to it. Many thanks!!!!!
I have the opposite problem, my wife and mother in law think I can work on any and everything 😅 it took 20yrs for me to make them understand, lm not a jack of all, I just play one ,if I say it's too boocoo ,believe me and move on 🤣
As a seasoned machine repairman... The Video streamlined the repair. Knowing in advance what to look for, and tear-down order was an Immense help! First time doing this and completed in 1 1/2 hours... getting tools together, tear-down and assembly. Your video was spot on except for driving shaft and bearings out. That was somewhat longer than your video showed, which caused me to wonder if I missed something..(Laughed at self). But Great Video and thank you for sharing!
Thanks for the tutorial. I just finished fixing mine. No more 'jet engines' in my basement. Honestly, I could have just bought a new machine, it's not beyond my budget. I just like the feeling of triumph when I fix my own stuff.
Great video, replace bearings and drive shaft, threw it back together and it worked! Use of the scissors jack was brilliant! Thank you for posting this.
Super video, instructions are clear and very well explained. I did bearing replacement on my washer following your video and my Maytag Bravos works now like a new one ! Thank you very much !
Holy Moly, Batman. Extremely well presented video. Concise and yet you fully explained every single step. I've got a Bravos XL model to do and will be looking for the alternate 'loosening' of the top that one of your commenters mentioned. I thought this job was going to be a nightmare, but your video is going to make the job easy... Keep up the excellent work. Really, really brilliant explanations at every step. The use of the scissors jack was especially ingenious. Thanks, Phil!
This is an excellent tutorial. Great for a beginner, or someone like myself...a seasoned mechanic who is not familiar with the machine. This was a big help!
Thanks for Great video! The only thing I would add would be to make sure the bearings are seated all the way or you will be taking the shaft and seal apart again or the cap for the agitator will not seat properly. I used a small bottle jack which made it easy but any port in a storm.
This is one of the most informative methods of changing bearings on the internet by far, thanks so much Phil. Now I'm gonna look one more time and then tackle my Cabrio washing machine, actually the parts is not here yet, but as soon as they reached I will, my confidence is so so high.
Thank you so much for sharing this howto. I have a Maytag Bravos MVWX600XW0 and this helped me decide whether to call someone or do it all myself. Removing the drum seems like the hardest part of the job.
Getting the tub and driveshaft and bearings out is all a roll of the dice. My tub was stuck but I used a piece of 2 X 4 cut to fit inside the drum and the scissor jack from my truck and it came right out. The driveshaft was hard to get out as well but I squirted it with PB Blaster penetrating oil and that helped. Really, taking it all apart was the hardest part.
Have watched several videos pertaining to this repair, but your tutorial encouraged me to take on this task. Very well explained and details were precise and clear. Thank you Sir!
Saved me hundreds of dollars! Bought the $54 kit in Amazon instead of the $120 just for the appliance guy to show up plus cost and labor. Took me 4 evenings because I had some differences and additional troubles I'll describe to help the next person: 1. My kid's licking tabs were different and additionally required unscrewing a 1/4" hex from the top of a green hinge on the back so the lid can be pulled forward and then the locking tabs pushed. 2. Same problem where I had to use a car jack and block of wood. 3. The nut on the bottom of the drive shaft was completely seized so I had to destroy it with a grinder. 4. Drive shaft was stuck and wouldn't come out with my 1 lb hammer. Don't waste your time people and just get a 4 lb hammer and it does the job. 5. Couldn't get the new drive shaft in, seemed like it was getting caught on the upper bearing and didn't want to destroy it by hammering it. Splintered my wood block trying to use that to hammer it. Eventually found out my car floor jack's handle fit perfectly over the splines onto the thick flat part, and hammered that instead where it eventually seated itself. 6. Don't forget to hook the drain back up before you run it for the first time! Oops.
Phil thank you so much for sharing this video. Because of you I’ve successfully fixed my washer following your video and saved at least $1000. I really appreciate your help! She’s running so quiet!:)))
Thank you so much for this great comment, Brad! Also, thank you so much for subscribing to my channel. I hope my other videos will help you out in the future.
Great Video a few call outs when pulling tub out washer I used the scissor jack method from another video. But it still required me to pount with a hammer on the large metal gear for a while don't be to afraid of hitting it hard and use the metal rod from the bearing kit. Lifting the washer up and down a lot requires space I pulled mine into the garage. This project took me about 5 hrs. It would have been less if I was not afraid of breaking tub by hitting gear really hard to get it out. This is the really hard part but cut wood to 22.5 inches and car sizzor jack made it a whole lot easier. The bearing too is a must to use. Clean every part you take out to make machine smell better.. Good luck.
Great instructional video laying out all the steps and each tool needed along the way. I've got the part ordered from Amazon and I'm just waiting for it to show up.
Absolutely wonderful teaching Vid-! Clear & precise! Excellent Teacher! Since my washer smells like metal burning whn n use, as they're obviously grinding down 2 bear metals, unfortunately, I think I may hav 2 pay exorbitant costs 4 repairs, or go buy a whole new one (vry close 2 wht repairs will be)...Curses...
Thanks for the detailed video. If the unit is just squeaky when moving, but won't run at high RPM (get UL code but have passed all other diagnostics and reset), is there reason to suspect bearings?
@@PhilCrockett thanks for the response. I added some temporary lubrication and it is better/working for now. Probably need to disassemble and add quality lubrication like silicon grease or motor oil. Not sure, but didn't have the resources to do all the procedures illustrated.
Excellent video - this helped immensely. One thing I would caution - when inserting the rubber seal, be very careful to properly seat and keep the spring in place. I nearly ruined the spring as the seal was very tight.
I clicked the amazon link and purchased the, OCTOPUS AP5325033 & AH3503307 W10435274 Bearings Washer Tool Kit. It didn't come with a thrust washer but instead a thrust bearing for the lower tub bearing install. Please note that the upper and lower bearing presses are not labeled, but they are different. The top has a longer press than than bottom. I watched the AppliancePartsPros video to get more information on this repair and it certainly looked like they used the wrong bearing press on top. Only 4-5 threads were showing on the bottom of the press rod. I bent the spacer tube and bottom bearing washer. I couldn't install the drive shaft, so be very careful. I simply used my OEM spacer tube and washer and the drive shaft inserted perfectly. The unit needs to seal overnight so I'll check back in after a few operational checks. Thanks again.
Fantastic video. I enjoyed watching it. I also decided to not pursue this route due to old age of the machine. So thank you for making it easy to make this decision by watching your video.
Thanks for the detailed video. I attempted this repair but now I'm seeing F:50 error message and washer doesn't seem to spin. I can move drum and agitator by hand so I don't think it's seized. I'm thinking maybe something wasn't plugged back in properly?
I figured it out. The connector shown at 10:30 looked like it was plugged in but one of the legs was not. Be careful when plugging this back in that all three terminals are connected.
This was just informative enough for me to make the decision that my washer has had a good life the last 6 years, and that I am not going to spend the time to probably fix a $380 washing machine 😌
Great video! But, had to chuckle about the use of "simply" remove the wash plate😂. Sometimes, that is the hardest part of this job. You can either make a couple hand tools to bend under the wash plate or buy a pair of trampoline spring stretchers.
Interesting. Apparently this is an issue with other folks as well. Someone suggested using a shoestring to get underneath the flange to help pull it out. I did not have any issues with the removal of the wash plate. This is why it's important to have comments. Thanks for commenting and watching the video as well
@PhilCrockett Thanks for the response. I work at an appliance parts store and removing the washplate is a complaint from most service techs. Some use air bags, strings or just break off the washplate and replace it. Personally, I like to keep plenty of different style agitators. Sometimes, you can swap out the washplate style with a full size agitator. I also always put some anti seize on anything I can.
Thank you so much for saying that! I don't get a whole lot of hits on this, but I do know it has helped a lot of people, and that's what gives me the satisfaction to keep doing this. Thanks again, and I hope you like my other videos as well.
I love this video! I did my bearing replacement on the same washer about 7 monhs ago. Washer came with my house and i think is 12 years old. Everything went well except last few months its getting louder. No so much durung final spin but as it spins during clean cycle. Loud squeak that sounds like the motor is struggling, somethings too tight, or notvlubed enough. Any ideas??
Super helpful video! I was super bummed after I fixed it all that it was throwing a Sd (5d) error code. Everything online said it was due to too much suds. But that error code is also due to the agitator not spinning with the tub. If you’re able to spin the agitator without the tub, you need to replace the washer hub kit which was 16$ Canadian on Amazon and voilà!
No grease on the bearing first at 7:50? I’m following this vid and another and the other vide they grease up the outer surface of the top and bottom bearings before pressing them together in place.
Phil I have cannot remember when I first sub’d to you but I have the same washer and developed a leak and need this to learn how to take it apart, thank you!
A few notes after doing this: not all lids open this way: I had to remove two screws in the rear and slide it forward. The kit I bought did not come with the bearing seat wrench. I tried making one, I tried renting one, but in the end, the only thing that worked for me was a hammer and a scrape 2x4. The Drum took forever to get out. PB penitraiting oil helps, but let it soak. I also used the car jack BUT I had to ad a strap to the board and rachet it to the ceiling in order to finally getit out. I had to put the bearings in and take them back out several times till I managed to get them in straight. I also had to hit the drive shaft in order to get that to seat. Initally, it was too high. Stripped one screw at the begining, but managed to get it out with pliers. One of the bolts on the bottom snaped off from over tighting it, but when all was said and done, it worked. Thank you for posting this very informative video.
Hi Phil, again. I got my parts today and started in replacing the bearings. I removed the basket and discovered there is trapped water inside of it. Have know idea how it got in there but that has to be a problem. Wondering what your thought is on that. Yes, the bearings are shot but I'm thinking the trapped water in the basket could be causing the UL (unbalanced load) alarm. I could drill holes and get it out and maybe fill the holes with silicone but maybe it will just go back in. Funny thing is no matter how I tip and hold the basket the water doesn't drip out anywhere. Looking for some advice. But the video you have here rocks and is the ticket for the bearings. Thanks so much. Maybe time to get a new basket?
Help!!! Somehow when using the bearing press, the washer became crooked. Now the shaft ont go in. How do I correct this without ruining the new bearings???
For all y'all struggling to [simply] lift the wash plate: my appliance pro uses a shoelace slid under the plate to work it loose. Somehow. I dunno. Maybe you can do something with that information.
great video took 2 attempts at seating the bearings first attempt i may have not set bearings deep enough using the puller and the new drive shaft did not want to fit without some tapping was difficult to turn driveshaft so i knocked out driveshat reseated new bearings and used the original driveshaft which fit perfectly could have been the new driveshaft was not exact size as original washer work’s great
Great job on the video first of all. Next I'm having trouble finding a bearing kit for my Maytag Bravos XL model MVWB835DW2 any ideas would be greatly appreciated! Thanks
no thats unbalanced load , the most likely issue is the suspension rods theres 4 holding in the inner tubreplace one at a time so the tub stays were it should very easy fix 10 mins even for a beginner only half hour or less.
Followed this video and it was great. Only one gotcha. In my case the washer between the sleeve and the bearing on the stattor side wasn’t tight enough in the diameter. Not sure why but after 3 attempts trying to get the shaft through (the washer just jumped around preventing the shaft to go through) we instant glued the washer to the sleeve to prevent that and bingo it worked. The glue held it just long enough to keep everything aligned.
The step with the adhesive on the seal after it is installed is missing on all other videos. This will be my third go around with this washer in the 10 years we have had it. I'm pretty confident that this is the missing step that will fix it long term this time. Thank you.
Thanks for the video. I would like to know if this replacement would probably fix the issue I’m having with my machine, it is the same model. It is giving the message UL during the spin. I already tried to check if there are some clothes stuck outside the barrel and it is clean.
Not sure if this was the same problem as yours. The problem with this machine was the bearings were rotted away and there was water leaking out on the floor
Nice video. Will be replacing mine for the second time in about 5 years. HE POS. Needed a refresher video to repair. New washers are so expensive. Just as much as HE whick I won't be buying next time around.
Phil, the replacement shaft I got has noticeable “slop” against the original hubs, which are still nice and tight against the original rusted out shaft. Think that’ll be a problem during operation?
@@PhilCrockett four months later and it’s still spinning. I got my money’s worth out of the fix on a 10 year old washer, but would definitely recommend the OEM replacement shaft.
Yo, Phil! You did a FINE job and that was a fine kit but when 'Old Squawky' gives it up it'll be time for Sweetums to go pick one out and get someone to bring it and get the old one. Probably Lowes. That thing sqawked and honked since it was turned on. The seller said it was the seal but I thought a seal barked. Different seal. I guess. Thanks, Buddy! Go fish, do not pass go and do not collect $200.00 and have a Jesus weekend! GBWYall
Ah ya! These washers are a lot harder to work on than dryers. I have a dryer video coming out at some point. Anyways........ I ALWAYS look forward to hearing from u. Keep in touch my brother!
My basket sits on the shaft and spins fine but when I put the drive hub on it doesn’t sit flush in the bottom of the basket. The drive hub pulls the basket up the shafts slightly when I tighten the screws so all the weight is on the drive hub. Doesn’t seem right. I measured both shafts and they are within .007” measuring from the tip to the shoulder. Any help is appreciated.
It's been a while since I've done this. Unfortunately I do not have any advice for you or recommendations. This will take some research online. I find that forums are a good resource
The tool I made was a last minute decision. Most people will not have this problem. However, you can actually purchase a bearing puller on the Internet. Indeed, this is a very difficult situation. The tool I made was constructed from a garage door spring ring and a bolt, a piece of pipe, and a nut. It's complicated.
First off thank you for making this video. I have one question Should my rooter be hard to turn by hand once I install the top gasket or should it still turn freely? I have my washer apart waiting on your comment. Thanks
Hey Jimmy Lee, I know this msg is not for me but I just wanted to let you know that it's a magnetic force so it will kinda stiff because they're no electricity there to move them freely...just saying.
@@PhilCrockett once i got the bottom bearing out i used the old drive shaft inserted in the bottom of the tub and hit it with a hammer and the top bearing popped out easy. My top bearing was in tact though if its in pieces this might not work well.
im mid process here. got the new shaft in but when i check if it spins it seems like it has sticky spots and does not spin smoothly. Is that going to burn the motor or work itself out over time. Any suggestions or tips?
Thanks for the video! I have a question for you. My bearing is going and getting louder. Now I have a UL (unbalanced load) alarm. Could a bad bearing cause the UL alarm? I'm thinking that's also do to the bearing going but want your opinion on this. Thanks!! Pete
I have no idea, Pete. Diagnosing via texting is not my thing. I would go to a forum and search. I love forums, I've learned a lot from them. As far as the balancing problem, there might be too many variables to consider. I'm not a professional appliance repairman. I only post videos on DIY that I absolutely know how to do. I can't help with diagnosing this. Let me know what you find out, and we can all learn from each other.
yes and no. my washer worked that bottom 1/4 inch hex bolt out. tub then wasn't very secure. as a result I got UL. first thought it was a problem I had a year ago: clothing stuck between tube wall (remove top clip as described in this video and look inside). tis time it was bearings: after the bottom bolt had been gone for an unknown amount of time, the bottom bearing was trashed.
there are various styles of bearing pullers you can buy. I feel your pain! I almost gave up on this one. Visit your local appliance repair store and pick their brains. Have them show you what they use.
THAT'S FANTASTIC, JAMES!!! I love this sort of feedback. I hope my other videos can help you out as well in the future. Thanks for taking the time to comment!
The bottom of my Maytag Bravos has water in it...I can hear it sloshing under washer drum...is this normal....how can i tip machine, replace bearings if machine has water in bottom??
Hopefully someone can answer. I'm going to be doing my bearing once it arrives. But is there suppose to be water INSIDE the drum ? I pulled the drum out and there is a good amount of water inside of it sloshing around
my drum has water in it too. Not much but it sloshes around. It's been that way for years and doesn't seem to affect the performance. It is weird. I actually wondered if it came that way. Must be a little leak. I figure you could drill a little hole in plastic and drain it then patch it up with epoxy seal. But I figure water will get back in. Let it ride.
To open my top there are 2 hook like tabs on both sides about 5" from the front corners that would not allow me to lift it without moviing the top forward, Forcefully.
@PhilCrockett I actually ended up melting it out and then melting it back into place using a blowtorch xD would not recommend, could have gone very poorly by melted to the tongue instead of just making it like pliable
What was the kit #, and maybe post a link Where you purchased the kit. I have the Bravos 300, but finding kits for the XL. EXCELLENT VIDEO;very linear in your explanation.
I added a piece of metal under the 2x4 so the wood wouldn’t keep cracking and this did the trick make sure you allow the PB blaster to work for a hr before trying to remove drum spray a good amount mine was stuck so good it broke boards
I did everything as shown in the video, but after installation I did a test (mode test) the whole test was ok. When I put the laundry to wash I got a Sd F 71 fault, I replaced the hub, the test showed ok, after putting the laundry again the same fault, I did the test mode, again the same fault, I changed the hub again, same thing again. Does anyone know what the problem is, thanks
That's how you make a "how to" video: perfect audio, perfect pace, no silly commentary, concise, just perfect in every way. Thank you sir!
Glad it helped!
copy and paste
Solved my rotor issue. On my washer there is a heavy duty magnet which made it require more of a tug to get the rotor off.
Most of the work is done. Just waiting 24 hours for the glue to dry.
Great video!
I really enjoy doing projects, especially when my wife doesn’t think I’m up to it.
Many thanks!!!!!
excellent! top work!
I have the opposite problem, my wife and mother in law think I can work on any and everything 😅 it took 20yrs for me to make them understand, lm not a jack of all, I just play one ,if I say it's too boocoo ,believe me and move on 🤣
As a seasoned machine repairman... The Video streamlined the repair. Knowing in advance what to look for, and tear-down order was an Immense help! First time doing this and completed in 1 1/2 hours... getting tools together, tear-down and assembly. Your video was spot on except for driving shaft and bearings out. That was somewhat longer than your video showed, which caused me to wonder if I missed something..(Laughed at self). But Great Video and thank you for sharing!
You're welcome!
I had some trouble getting the driveshaft out but it's because I did't have a big enough hammer but once I got it out everything fell into place.
Perfect!
Still saving our asses 3 years later, My top bearing did the same thing and i couldnt get the ring out. I appreciate you!
Thank you so much for this comment! Comments like yours keeps me going!
Thanks for the tutorial. I just finished fixing mine. No more 'jet engines' in my basement.
Honestly, I could have just bought a new machine, it's not beyond my budget. I just like the feeling of triumph when I fix my own stuff.
Glad it helped
Great video, replace bearings and drive shaft, threw it back together and it worked! Use of the scissors jack was brilliant! Thank you for posting this.
Glad it helped
Super video, instructions are clear and very well explained. I did bearing replacement on my washer following your video and my Maytag Bravos works now like a new one ! Thank you very much !
Your video saved me. Thanks for taking the time to record it for the rest of us.
Glad it helped you out!
This is the best tutorial I’ve found online by far! Thank you for taking the time to explain in detail
You're very welcome. Debbie!
This is such a well made video, incredibly detailed step-by-step procedure. Thanks for taking the time to make this!
Glad it helped you out, Pete!
Man, the level of explanation and detail in this how-to is just AWESOME.
glad my video helped you out
Holy Moly, Batman. Extremely well presented video. Concise and yet you fully explained every single step. I've got a Bravos XL model to do and will be looking for the alternate 'loosening' of the top that one of your commenters mentioned. I thought this job was going to be a nightmare, but your video is going to make the job easy... Keep up the excellent work. Really, really brilliant explanations at every step. The use of the scissors jack was especially ingenious. Thanks, Phil!
So glad my video helped you out, Dean! Thanks for watching and taking the time to comment.
This is an excellent tutorial. Great for a beginner, or someone like myself...a seasoned mechanic who is not familiar with the machine. This was a big help!
Glad it was helpful!
Thanks for Great video! The only thing I would add would be to make sure the bearings are seated all the way or you will be taking the shaft and seal apart again or the cap for the agitator will not seat properly. I used a small bottle jack which made it easy but any port in a storm.
Great tip! thanks for watching and taking the time to comment.
This is one of the most informative methods of changing bearings on the internet by far, thanks so much Phil.
Now I'm gonna look one more time and then tackle my Cabrio washing machine, actually the parts is not here yet, but as soon as they reached I will, my confidence is so so high.
Donald, if I can do it, anyone can! thanks for watching and commenting. Hope my other videos are just as useful to you!
Thank you so much for sharing this howto. I have a Maytag Bravos MVWX600XW0 and this helped me decide whether to call someone or do it all myself. Removing the drum seems like the hardest part of the job.
You're welcome, Maulik!! thanks for taking the time to comment.
Getting the tub and driveshaft and bearings out is all a roll of the dice. My tub was stuck but I used a piece of 2 X 4 cut to fit inside the drum and the scissor jack from my truck and it came right out. The driveshaft was hard to get out as well but I squirted it with PB Blaster penetrating oil and that helped. Really, taking it all apart was the hardest part.
Have watched several videos pertaining to this repair, but your tutorial encouraged me to take on this task. Very well explained and details were precise and clear. Thank you Sir!
You are welcome! Hope you like my other DIY videos too, Leonard!
I am an appliance tech and business owner and have done many of these. Your video is excellent
Thanks, Alex!!!! That really means a lot to me! Please share my video with as many people in your business as you can. I love the views! Thanks again!
Saved me hundreds of dollars! Bought the $54 kit in Amazon instead of the $120 just for the appliance guy to show up plus cost and labor. Took me 4 evenings because I had some differences and additional troubles I'll describe to help the next person:
1. My kid's licking tabs were different and additionally required unscrewing a 1/4" hex from the top of a green hinge on the back so the lid can be pulled forward and then the locking tabs pushed.
2. Same problem where I had to use a car jack and block of wood.
3. The nut on the bottom of the drive shaft was completely seized so I had to destroy it with a grinder.
4. Drive shaft was stuck and wouldn't come out with my 1 lb hammer. Don't waste your time people and just get a 4 lb hammer and it does the job.
5. Couldn't get the new drive shaft in, seemed like it was getting caught on the upper bearing and didn't want to destroy it by hammering it. Splintered my wood block trying to use that to hammer it. Eventually found out my car floor jack's handle fit perfectly over the splines onto the thick flat part, and hammered that instead where it eventually seated itself.
6. Don't forget to hook the drain back up before you run it for the first time! Oops.
Yep.... not easy sometimes, but worth the time to save a lot of money!
This video was perfect! We followed step by step with no problems! Thank you
You're welcome!
Extremely well done video! Your instructions were clear and concise. There wasn't a single unnecessary step and every step worked as described.
Glad you liked it, Geoff!!!!
Phil thank you so much for sharing this video. Because of you I’ve successfully fixed my washer following your video and saved at least $1000. I really appreciate your help! She’s running so quiet!:)))
Thank you so much for this great comment, Brad! Also, thank you so much for subscribing to my channel. I hope my other videos will help you out in the future.
I just replaced the bearings today by following this video. Step by step, everything went smooth and had a great outcome. Thanks for the info.
yOu're welcome
Great Video a few call outs when pulling tub out washer I used the scissor jack method from another video. But it still required me to pount with a hammer on the large metal gear for a while don't be to afraid of hitting it hard and use the metal rod from the bearing kit. Lifting the washer up and down a lot requires space I pulled mine into the garage. This project took me about 5 hrs. It would have been less if I was not afraid of breaking tub by hitting gear really hard to get it out. This is the really hard part but cut wood to 22.5 inches and car sizzor jack made it a whole lot easier. The bearing too is a must to use. Clean every part you take out to make machine smell better.. Good luck.
Ya.... this is a lengthy project for sure.... however, it definitely saves money doing it yourself.
Great how-to video. Made me feel confident enough to pull my washer apart and I'm not even sure what is wrong with it.
Glad it helped
Great instructional video laying out all the steps and each tool needed along the way. I've got the part ordered from Amazon and I'm just waiting for it to show up.
Let me know how it worked out
Absolutely wonderful teaching Vid-! Clear & precise! Excellent Teacher!
Since my washer smells like metal burning whn n use, as they're obviously grinding down 2 bear metals, unfortunately, I think I may hav 2 pay exorbitant costs 4 repairs, or go buy a whole new one (vry close 2 wht repairs will be)...Curses...
Glad it was helpful!
Thanks for the detailed video. If the unit is just squeaky when moving, but won't run at high RPM (get UL code but have passed all other diagnostics and reset), is there reason to suspect bearings?
beats me. this one was leaking all over the floor and sounded like shot bearings.
@@PhilCrockett thanks for the response. I added some temporary lubrication and it is better/working for now. Probably need to disassemble and add quality lubrication like silicon grease or motor oil. Not sure, but didn't have the resources to do all the procedures illustrated.
Very informative and step by step instructions. Thank you for taking the time to video, edit, and post!
Thanks for watching and commenting! Glad my video helped!
Excellent video - this helped immensely. One thing I would caution - when inserting the rubber seal, be very careful to properly seat and keep the spring in place. I nearly ruined the spring as the seal was very tight.
Great tip!
I clicked the amazon link and purchased the, OCTOPUS AP5325033 & AH3503307 W10435274 Bearings Washer Tool Kit. It didn't come with a thrust washer but instead a thrust bearing for the lower tub bearing install. Please note that the upper and lower bearing presses are not labeled, but they are different. The top has a longer press than than bottom. I watched the AppliancePartsPros video to get more information on this repair and it certainly looked like they used the wrong bearing press on top. Only 4-5 threads were showing on the bottom of the press rod. I bent the spacer tube and bottom bearing washer. I couldn't install the drive shaft, so be very careful. I simply used my OEM spacer tube and washer and the drive shaft inserted perfectly. The unit needs to seal overnight so I'll check back in after a few operational checks. Thanks again.
Let me know how it worked out.
Fantastic video. I enjoyed watching it. I also decided to not pursue this route due to old age of the machine. So thank you for making it easy to make this decision by watching your video.
it definitely took quite a bit of effort.
Thanks for the detailed video. I attempted this repair but now I'm seeing F:50 error message and washer doesn't seem to spin. I can move drum and agitator by hand so I don't think it's seized. I'm thinking maybe something wasn't plugged back in properly?
I figured it out. The connector shown at 10:30 looked like it was plugged in but one of the legs was not. Be careful when plugging this back in that all three terminals are connected.
glad you got it working!
I used a bottle jack instead of scissor jack. Other than that I used my impact drill to take it apart and back together. This video is very good.
excellent
Helped me out enough to let me know I'm not doing this. Thank you
Thank you for taking the time to watch and comment, my friend!
Count me among the many thankful! Using your video, the job was a breeze (other than getting the tub out, that was a sonofab****!).
ya. it wasn't fun!
This was just informative enough for me to make the decision that my washer has had a good life the last 6 years, and that I am not going to spend the time to probably fix a $380 washing machine 😌
good call! it really was a lot of work.
You are amazingly and pleasantly clear and concise with your instructions! Great job on the Clip!
Thanks, Bill! Hope you follow my other DIY vids as well, and they help you out in the future.
Thank you! This tutorial turned a nightmare in to a dream! 2.5 hours soup to nuts, including gathering all the tools
I am so glad my video helped you out! Thank you for taking the time to watch and comment!
Great video! But, had to chuckle about the use of "simply" remove the wash plate😂. Sometimes, that is the hardest part of this job. You can either make a couple hand tools to bend under the wash plate or buy a pair of trampoline spring stretchers.
Interesting. Apparently this is an issue with other folks as well. Someone suggested using a shoestring to get underneath the flange to help pull it out. I did not have any issues with the removal of the wash plate. This is why it's important to have comments. Thanks for commenting and watching the video as well
@PhilCrockett Thanks for the response. I work at an appliance parts store and removing the washplate is a complaint from most service techs. Some use air bags, strings or just break off the washplate and replace it. Personally, I like to keep plenty of different style agitators. Sometimes, you can swap out the washplate style with a full size agitator. I also always put some anti seize on anything I can.
Excellent diy! It's my 2nd time using your video. Next time I'll have to replace the shaft as well (the stainless sleeve is grooved).
Makes my day knowing that my video helped you out twice!
Great step by step video most informative I’ve seen Thanks
Glad to help, Fred!
This is the absolute best video for this repair.
Thank you so much for saying that! I don't get a whole lot of hits on this, but I do know it has helped a lot of people, and that's what gives me the satisfaction to keep doing this. Thanks again, and I hope you like my other videos as well.
I love this video! I did my bearing replacement on the same washer about 7 monhs ago. Washer came with my house and i think is 12 years old. Everything went well except last few months its getting louder. No so much durung final spin but as it spins during clean cycle. Loud squeak that sounds like the motor is struggling, somethings too tight, or notvlubed enough. Any ideas??
Not sure. Maybe more lube since it's squeaking
Super helpful video! I was super bummed after I fixed it all that it was throwing a Sd (5d) error code. Everything online said it was due to too much suds. But that error code is also due to the agitator not spinning with the tub. If you’re able to spin the agitator without the tub, you need to replace the washer hub kit which was 16$ Canadian on Amazon and voilà!
thanks for commenting, maybe this will help someone else out!
No grease on the bearing first at 7:50?
I’m following this vid and another and the other vide they grease up the outer surface of the top and bottom bearings before pressing them together in place.
interesting. I do know the seal that is filled with grease acts as a dispenser to the bering.
Bearings are suppose to be pre lubed and sealed. Should has rs after bearing number
Very clear instructions. Especially the callout titles.
thanks!
Phil I have cannot remember when I first sub’d to you but I have the same washer and developed a leak and need this to learn how to take it apart, thank you!
You made my day with this comment, Captain!
?from NY ? Did you sell as Honda Nighthawk - very nice machine
What is the purpose of the weep hole? This is the first video I’ve seen that instructed to clean it out
it's kind of like a small drain hole.
A few notes after doing this:
not all lids open this way: I had to remove two screws in the rear and slide it forward.
The kit I bought did not come with the bearing seat wrench. I tried making one, I tried renting one, but in the end, the only thing that worked for me was a hammer and a scrape 2x4.
The Drum took forever to get out. PB penitraiting oil helps, but let it soak. I also used the car jack BUT I had to ad a strap to the board and rachet it to the ceiling in order to finally getit out.
I had to put the bearings in and take them back out several times till I managed to get them in straight.
I also had to hit the drive shaft in order to get that to seat. Initally, it was too high.
Stripped one screw at the begining, but managed to get it out with pliers. One of the bolts on the bottom snaped off from over tighting it, but when all was said and done, it worked. Thank you for posting this very informative video.
It didn't go ez for me either......due to that bearing ring getting stuck.
Hi Phil, again. I got my parts today and started in replacing the bearings. I removed the basket and discovered there is trapped water inside of it. Have know idea how it got in there but that has to be a problem. Wondering what your thought is on that. Yes, the bearings are shot but I'm thinking the trapped water in the basket could be causing the UL (unbalanced load) alarm. I could drill holes and get it out and maybe fill the holes with silicone but maybe it will just go back in. Funny thing is no matter how I tip and hold the basket the water doesn't drip out anywhere. Looking for some advice. But the video you have here rocks and is the ticket for the bearings. Thanks so much. Maybe time to get a new basket?
I haven't had that problem before. hmmmmm..... maybe use a forum to see if someone else has had that.
The fluid in the basket is for balance as the tub load shifts
thanks for the tip!
@@Harveje man I have learned so much from you guys just reading here.
@@Harveje yes. but if it is significantly more, check drain motor and port in tub.
Absolutely 'excellent' presentation of "how-to"!
Thanks!
Help!!!
Somehow when using the bearing press, the washer became crooked.
Now the shaft ont go in.
How do I correct this without ruining the new bearings???
To clarify: the washer between the the metal spacer and the bottom bearing is what became crooked.
I'd try re-setting the bearing with the press
Same here Tyler, I’m trying to correct the same issue. I even put the washing machine flat on its back thinking not being at an angle would help.
When I knocked out bottom bearing I noticed the cylindrical shaft that the bearing sits has a small piece that’s cracked off. Will this still seal?
hard to say without seeing it, but an abundance of epoxy might be your best bet.
Thanks for this well presented and thorough demonstration. It was just what I needed.
Glad it was helpful, Sean!
For all y'all struggling to [simply] lift the wash plate: my appliance pro uses a shoelace slid under the plate to work it loose. Somehow. I dunno. Maybe you can do something with that information.
Thanks for helping folks out! That's what these comments are for! Respect!
great video
took 2 attempts at seating the bearings
first attempt i may have not set bearings deep enough using the puller and the new drive shaft did not want to fit without some tapping
was difficult to turn driveshaft so i knocked out driveshat reseated new bearings and used the original driveshaft which fit perfectly
could have been the new driveshaft was not exact size as original
washer work’s great
definitely not the easiest job to do.
Great job on the video first of all. Next I'm having trouble finding a bearing kit for my Maytag Bravos XL model MVWB835DW2 any ideas would be greatly appreciated! Thanks
I really don't know......
no thats unbalanced load , the most likely issue is the suspension rods theres 4 holding in the inner tubreplace one at a time so the tub stays were it should very easy fix 10 mins even for a beginner only half hour or less.
Video explained everything perfectly. Got the machine fixed and it’s good as new. Thank you!
You're welcome, Tyler!
Followed this video and it was great. Only one gotcha. In my case the washer between the sleeve and the bearing on the stattor side wasn’t tight enough in the diameter. Not sure why but after 3 attempts trying to get the shaft through (the washer just jumped around preventing the shaft to go through) we instant glued the washer to the sleeve to prevent that and bingo it worked. The glue held it just long enough to keep everything aligned.
There's always a "Gacha" when dealing with this
Great Job, only thing i found different was the top Lid on mine. Removed two 1/4 inch screws and slide top forward to swing up.
Glad my video helped you out, Jeff! Hope you like my other ones too.
The step with the adhesive on the seal after it is installed is missing on all other videos. This will be my third go around with this washer in the 10 years we have had it. I'm pretty confident that this is the missing step that will fix it long term this time. Thank you.
Glad my video could help you out
Thanks for the video. I would like to know if this replacement would probably fix the issue I’m having with my machine, it is the same model. It is giving the message UL during the spin. I already tried to check if there are some clothes stuck outside the barrel and it is clean.
Not sure if this was the same problem as yours. The problem with this machine was the bearings were rotted away and there was water leaking out on the floor
Hello, did you end up finding the problem for the ul code? I am experiencing the ul code and have water leaking on the floor
Nice video. Will be replacing mine for the second time in about 5 years. HE POS. Needed a refresher video to repair. New washers are so expensive. Just as much as HE whick I won't be buying next time around.
Thanks for watching and commenting, Mike! These appliances keep getting junkier by the year.
Phil, the replacement shaft I got has noticeable “slop” against the original hubs, which are still nice and tight against the original rusted out shaft. Think that’ll be a problem during operation?
gosh.... idk. there's only one way to find out. let me know. maybe it will help someone else
@@PhilCrockett four months later and it’s still spinning. I got my money’s worth out of the fix on a 10 year old washer, but would definitely recommend the OEM replacement shaft.
Well, what type of grease is it?
bearing grease. You can find it at an automotive store, or a big box store.
Should the spacer tube have any play in it after doing the press operation on the bearings?
Mine didn't
Great video! I just used the kit on the link and my washing machine works like new!! Thank you!
You're welcome, Arthur!
Yo, Phil! You did a FINE job and that was a fine kit but when 'Old Squawky' gives it up it'll be time for Sweetums to go pick one out and get someone to bring it and get the old one. Probably Lowes. That thing sqawked and honked since it was turned on. The seller said it was the seal but I thought a seal barked. Different seal. I guess. Thanks, Buddy! Go fish, do not pass go and do not collect $200.00 and have a Jesus weekend! GBWYall
Ah ya! These washers are a lot harder to work on than dryers. I have a dryer video coming out at some point. Anyways........ I ALWAYS look forward to hearing from u. Keep in touch my brother!
Great video! Curious if my particular washer model would be a similar job. GE Deep Fill top load…?
Not sure…. This was my buddy’s machine
Excellent instructional video. Thank you, Phil.
You’re welcome,!
My basket sits on the shaft and spins fine but when I put the drive hub on it doesn’t sit flush in the bottom of the basket. The drive hub pulls the basket up the shafts slightly when I tighten the screws so all the weight is on the drive hub. Doesn’t seem right. I measured both shafts and they are within .007” measuring from the tip to the shoulder.
Any help is appreciated.
That's a hard one to diagnose without seeing it. This one might need to be taken into the shop.
Hi,... Thanks for the video. I have the tools from a previous repair and kit... Can you recommend a bearing and seal kit only? Thanks.
It's been a while since I've done this. Unfortunately I do not have any advice for you or recommendations. This will take some research online. I find that forums are a good resource
I have the same issue with the top bearing.Do you have any videos on how you made the tool to remove the top bearing?
The tool I made was a last minute decision. Most people will not have this problem. However, you can actually purchase a bearing puller on the Internet. Indeed, this is a very difficult situation. The tool I made was constructed from a garage door spring ring and a bolt, a piece of pipe, and a nut. It's complicated.
What length was the 2x4?
Great video. Do I have to have a washer tool or is there another method?
You definitely need that tool.
Great video...I'm going to take a crack at repairing mine now...
You can do it!
First off thank you for making this video. I have one question Should my rooter be hard to turn by hand once I install the top gasket or should it still turn freely? I have my washer apart waiting on your comment. Thanks
The rotor was a bit hard to turn.
Hey Jimmy Lee, I know this msg is not for me but I just wanted to let you know that it's a magnetic force so it will kinda stiff because they're no electricity there to move them freely...just saying.
Phill, called Octopus and they don't have part's for my washer. Can't find a website that can help me.
Thanks again.
I wonder if there's an issue because Sears went out of business. hmmmm?🤔
I have Maytag MVWB955FC1 washer would it be the same process?
I'm not sure. Haven't worked on one of those. might get an explosion diagram to see.
Dang you're a patient man.
Not really.........
Thank you sir got it in. I guess im lucky the top bearing came out with the shaft
Yeah, you are super lucky! That top bearing is a pain in the butt! So glad my video helps you out, my friend!
@@PhilCrockett once i got the bottom bearing out i used the old drive shaft inserted in the bottom of the tub and hit it with a hammer and the top bearing popped out easy. My top bearing was in tact though if its in pieces this might not work well.
im mid process here. got the new shaft in but when i check if it spins it seems like it has sticky spots and does not spin smoothly. Is that going to burn the motor or work itself out over time. Any suggestions or tips?
seems like it sorted itself out once i bolted everything together. spins smooth and easy
Excellent! Glad to hear it!
Thanks for the video! I have a question for you. My bearing is going and getting louder. Now I have a UL (unbalanced load) alarm. Could a bad bearing cause the UL alarm? I'm thinking that's also do to the bearing going but want your opinion on this. Thanks!! Pete
I have no idea, Pete. Diagnosing via texting is not my thing. I would go to a forum and search. I love forums, I've learned a lot from them. As far as the balancing problem, there might be too many variables to consider. I'm not a professional appliance repairman. I only post videos on DIY that I absolutely know how to do. I can't help with diagnosing this. Let me know what you find out, and we can all learn from each other.
yes and no. my washer worked that bottom 1/4 inch hex bolt out. tub then wasn't very secure. as a result I got UL. first thought it was a problem I had a year ago: clothing stuck between tube wall (remove top clip as described in this video and look inside). tis time it was bearings: after the bottom bolt had been gone for an unknown amount of time, the bottom bearing was trashed.
I am having the same issue with the bottom bearing ring stuck/ what other methods can i use to get this ring out?
there are various styles of bearing pullers you can buy. I feel your pain! I almost gave up on this one. Visit your local appliance repair store and pick their brains. Have them show you what they use.
Great video, did everything you showed on the video turned out great!
THAT'S FANTASTIC, JAMES!!! I love this sort of feedback. I hope my other videos can help you out as well in the future. Thanks for taking the time to comment!
The bottom of my Maytag Bravos has water in it...I can hear it sloshing under washer drum...is this normal....how can i tip machine, replace bearings if machine has water in bottom??
No idea
The water is supposed to be there, they add water to keep it balanced. Look it up online it’ll explain it to you.
I did the install and did an empty test run. No leaks but when clothes are inside it leaks abit from the bottom ??
As far as I know, the only real good seal is from the epoxy glue
Straight to the point
Indeed! I hope all my videos are like this! That's my goal. Thank you for the comment
Very good job. Detailed explanation.
Glad it was helpful!
That was very informative. Thank you!
Glad it was helpful!
Hopefully someone can answer. I'm going to be doing my bearing once it arrives. But is there suppose to be water INSIDE the drum ? I pulled the drum out and there is a good amount of water inside of it sloshing around
my drum has water in it too. Not much but it sloshes around. It's been that way for years and doesn't seem to affect the performance.
It is weird. I actually wondered if it came that way. Must be a little leak. I figure you could drill a little hole in plastic and drain it then patch it up with epoxy seal. But I figure water will get back in. Let it ride.
I'm not sure what the problem is with that
To open my top there are 2 hook like tabs on both sides about 5" from the front corners that would not allow me to lift it without moviing the top forward, Forcefully.
Hmmmm.....🤔
Phil desde México un saludo y felicitaciones explicas muy claro todo el proceso.
I will have to Google translate this and get back to you
Do you know if this kit will work with the whirlpool bravos XL steam?
not sure.... sorry
Do you have any recommendations on removing that top bearing piece mine did the same thing :(
I don't. I had to make my own tool actually for the bearing that was stuck in place on this video.
@PhilCrockett I actually ended up melting it out and then melting it back into place using a blowtorch xD would not recommend, could have gone very poorly by melted to the tongue instead of just making it like pliable
What was the kit #, and maybe post a link Where you purchased the kit.
I have the Bravos 300, but finding kits for the XL.
EXCELLENT VIDEO;very linear in your explanation.
there are sooooo many models that this works on.... I really don't know.... best to find it on-line or call in.
j. Dm I need the one for Bravos XL and can't find one, could you share with me!
Excellent video! So incredibly helpful - thank you!!
Glad it was helpful!
My tub is stuck so badly it’s crack 2 boards now trying to remove
I added a piece of metal under the 2x4 so the wood wouldn’t keep cracking and this did the trick make sure you allow the PB blaster to work for a hr before trying to remove drum spray a good amount mine was stuck so good it broke boards
dang!
I did everything as shown in the video, but after installation I did a test (mode test) the whole test was ok. When I put the laundry to wash I got a Sd F 71 fault, I replaced the hub, the test showed ok, after putting the laundry again the same fault, I did the test mode, again the same fault, I changed the hub again, same thing again. Does anyone know what the problem is, thanks
I'll post this..... hope you find someone that can answer this..... I sure can't