wonderful! I sent the same watch into Citizen for a service. It came back fully working and they only charged £60. However, I suspect that they probably just swapped out the movement and threw the old one away. Lovely to see the love, attention, and time given to restore this beautiful old watch.
Wonderful work, but oh boy that chapter ring is totally misaligned....not just a bit, but totally. You probably missed it, but it's with those things that we learn to become even better. Hope you fixed it.
some say you need to let the presure out of the cilinder with the watch case still in the water. only then you can say if bubles coming out or not is a sing of water tight. also test the case only before encolsing the movment within it. if anything goes wrong, the movment dial and hands are still dry and all you need is to sort out a case.
Wow. I have a ‘thing’ for Citizen and Seiko divers watches. I’ve just sat in awe of this video. I wish I had the knowledge, equipment, steady hands, patience to do this. Thanks so much for the insight. Simply superb!!!
I admire your dedication in every single little detail; especially the amount of patience you had when you tried to remove every bit of debris and residual glue from the bezel groove beneath the spring😊
@@wristwatchobsession5585 But you should let the air out of the testing device before you take the watch out of the water. It is then when bubbles will appear if the watch is not sealed.
Great video I have a citizen promaster and have used it down to 20 metres and on dives here in Ireland off the Hook Head light house, they are very reliable watch. mine is not automatic though. again thanks for sharing your great video, cheers from Ireland. ( edited to remove the same word twice. )
Very nice Video. I have an old Citizen Promaster NY0040, if I put it down overnight it runs -160 seconds a day and if I wear it during the day it runs +240 seconds a day.
@@mark_clift hi Mark Yes rodico is a good idea. Thank you. but I didn’t want to cover it in my video so people can see it better and then end up searching for it 😂
bel video...solo una precisazione, perchè prima di montare il vetrino non hai spolverato con una pompetta il quadrante? infatti dentro e' rimasta polvere......video bellissimo complimenti!!!!
Hi! great video, I wanted to ask if aftermarket seiko dials and chapter rings would fit a citizen promaster? I want to replace my dial and just hoping for some insight. Thanks!
Nice video. One question: Was the pressure-test procedure in the video meant as a joke to see anyone was paying attention? (You're supposed to release the pressure with the watch submerged to check for bubbles..).
2 methods. 1 have it in the water and pump the pressure up. If it fills up its leaking (and damaged) 2 you have it above the water, pump up the pressure (if there are any leaks, the air pressure in the watch will go up) then lower it in the water and release the pressure valve. If there was a leak then this will show as bubbles from the effected area as the pressure in the tank becomes normal and the watch equalises with the outside pressure. This way when you find a leak, you can lift it up quick to save the watch.
Great video! Would love to see a side by side comparison at the end of the video of the beginning and final product to see the difference the restoration has made.
Hallo, erst einmal meinen Dank an Dich für Deine tollen Videos! Aber eine Frage habe ich zu diesem Video hier: Ziemlich am Ende des Videos machst Du einen Drucktest auf Wasserdichtigkeit mit der restaurierten Uhr. Du baust Druck im Tester auf, senkst die Uhr in das Wasser ab, schreibst dann "No Bubble, No Trouble", hebst die Uhr wieder aus dem Wasser heraus und lässt (der Tonspur zufolge) DANN den Druck ab. Müsstest Du nicht den Druck langsam ablassen _solange die Uhr noch unter Wasser ist_, um zu schauen ob DABEI (beim Ablassen des Drucks) Blasen aufsteigen? Sie bei erhöhtem Aussendruck einfach einmal die Uhr einzutauchen und wieder herauszuholen sagt ja nichts aus…
Question about this same model: mine stopped so I opened it to find that the pallet fork correctly engages the escape wheel but everything else is not moving as soon as I put back the bridge... Any advice?
Hi it can be a lot of things from a Brocken week tooth to a Brocken barrel spring. You have to inspect all the parts under microscope. If nothing is Brocken it should work after cleaning.
My first dive watch from a decent brand with some horological history was a Promaster Dive eco-drive. I’m looking for a Promaster automatic but to find one for sale is nigh impossible.
Not anywhere close to impossible as they are very common and easily accessible and available for sale all the time from many companies and individuals.
Funny .. Red Dead Restoration did this same model watch last year .. it had the same problem .. broken pivot on the pallet fork. Seems a common problem with this watch.
I've just recently bought the fully lumed version of this watch. Unfortunately I noticed that the bezel is very slightly misaligned. I had considered sending it back but is it possible to remove the bezel and reseat it so that it lines up correctly?
Hey, i own a similar ny0080. I removed the bezel a while ago but i never manage to put it back in. I dont know where i could get the proper bezel wire for the case. I got one for a vostok but seems to be extremely difficult to sit in. I got a basic watch crystal press. Any advice?
So the movement, dial, etc doesn’t get my fingerprints. Also I think it looks better than pink and white finger cots although finger cots are more comfortable to wear 🙂
I just noticed that red seconds hand. Could that be aftermarket? That's supposed to be an ISO Certified Diver's watch. Without lume on that seconds hand, it can't be.
@@wristwatchobsession5585 No, but when you pressure test as a repair person, they typically keep the movement out during that step to ensure water resistence works, to protect the movement. If you treat it with a valuable movement inside and it gets wet, it could be trouble for you.
Incredible! Very nice video. Enjoyed it very much. Great job !
Thank you so much Sir!
and what a privilege, an executive VP from Novo Nordisk watching my videos!!
Great work and thoroughly professionally. I need two bezel inserts. How can I get them please?
Thanks
One of the most beautiful watches ever made!
wonderful! I sent the same watch into Citizen for a service. It came back fully working and they only charged £60. However, I suspect that they probably just swapped out the movement and threw the old one away. Lovely to see the love, attention, and time given to restore this beautiful old watch.
Hi! What was the original movement? Did they swap it for a hackable movement?
Wonderful work, but oh boy that chapter ring is totally misaligned....not just a bit, but totally. You probably missed it, but it's with those things that we learn to become even better. Hope you fixed it.
Good ol' citizen automatic divers watch. They really are a very very good strong watch. Brilliant video 👍.
some say you need to let the presure out of the cilinder with the watch case still in the water. only then you can say if bubles coming out or not is a sing of water tight. also test the case only before encolsing the movment within it. if anything goes wrong, the movment dial and hands are still dry and all you need is to sort out a case.
Wow.
I have a ‘thing’ for Citizen and Seiko divers watches.
I’ve just sat in awe of this video. I wish I had the knowledge, equipment, steady hands, patience to do this.
Thanks so much for the insight.
Simply superb!!!
Very impressive. That's a watch to be proud to wear!
Fantastic. Just the right length too. I don't always have time to watch 30-40 minute restorations.
Thank again Dave. I appreciate all your comments 🙏
I admire your dedication in every single little detail; especially the amount of patience you had when you tried to remove every bit of debris and residual glue from the bezel groove beneath the spring😊
This beautiful watch from citizen certainly deserve to be restored. Greatly filmed too.
No bubbles no troubles. I like that. 😄 Fantastic restoration as always! Keep up the good work. 😊
Thank you so much :-)
@@wristwatchobsession5585 But you should let the air out of the testing device before you take the watch out of the water. It is then when bubbles will appear if the watch is not sealed.
@@wristwatchobsession5585This is probably one of the oldest ones
Well photographed, well lit. Thank you for posting.
Thanks for watching
This one and the SKX007J are most beautiful watches...just a pity they are so expensive!!Awesome restoration!
Debeer, how ya been?
Very impressive! I could never do that. Nice to look AT! 🤔👍🏻
Very helpful! I have a citizen promaster for restore and i will begin
Great video I have a citizen promaster and have used it down to 20 metres and on dives here in Ireland off the Hook Head light house, they are very reliable watch. mine is not automatic though. again thanks for sharing your great video, cheers from Ireland. ( edited to remove the same word twice. )
Seem to be more common than Seiko here in Ireland
I nearly sold my NY0040. Glad I never after watching this. Nice work
Génial comme travail sur cette CITIZEN 👍
Respect Mec ! 👏
Very well done!..and your camera work is incredible!
Thank you from Denver North Carolina
Really enjoy watching your videos. Clean work and well done!
Thank you so much 😊
Nice video, congratulations. I would have kept the old bezel, it has its charm
I have this same watch. Amazing watch for the money. Looks fantastic and keep VERY accurate time.
Job well done.
Thank you 😊
Very nice Video. I have an old Citizen Promaster NY0040, if I put it down overnight it runs -160 seconds a day and if I wear it during the day it runs +240 seconds a day.
Get a quartz if you want functional accuracy.
Wish I had all those tools of the trade!
Magnificent service, you do a great job, I have a similar watch 8203, where did you get the spare parts???
Greetings from Mexico
Yes, where did you get the new spares from???
Mine is working perfectly a long for 30 years! Only oiled the rotor for the automatic winding. Want to change the yellow dial against a black one…
Came over from Instagram. I look forward to watching both of your videos this evening!
THANK YOU 🙏
@@wristwatchobsession5585 good idea to hold some rodico on the other side of the circlip. I have spent hours looking for springs too!
@@wristwatchobsession5585 Nice video, just be cautious of the small lint fibres. Do you have somewhere else you can do case polishing?
@@mark_clift hi Mark
Yes rodico is a good idea. Thank you.
but I didn’t want to cover it in my video so people can see it better and then end up searching for it 😂
why you change the bezel and arrows from Gold to Silver? i have the same watch ny0045 and i love the gold
I think it's impossible to get these golden parts, I don't find them anywhere.
Outstanding video 👍
Why is your movement so dusty during assembly? There was dust all over it in various stages. I don't see that in other watch restoration videos.
bel video...solo una precisazione, perchè prima di montare il vetrino non hai spolverato con una pompetta il quadrante? infatti dentro e' rimasta polvere......video bellissimo complimenti!!!!
What a great video, I'm definitely a new subscriber =). I'm a fan of citizen, it's a very nice watch, where is it from, ebay?
Looks amazing!
Hermoso trabajo y hermoso reloj
From italy beatiful
You're supposed to let out the pressure when the watch is in the water
I just asked him the same question.
@@lordgicht6630ele não fez uma pergunta.
Hi! great video, I wanted to ask if aftermarket seiko dials and chapter rings would fit a citizen promaster? I want to replace my dial and just hoping for some insight. Thanks!
No it won’t fit unfortunately
Amazing! Great video. Where did you get the new chapter ring from? I've been trying to find one for ages now.
Very enjoyable and very relaxing. What's your thoughts on plastic parts in the movement?
They are extremely fragile!
But I guess this is how you save some money? Don’t know ☺️
Plastic also doesn’t need any lubricants but seems cheap. Seiko did the same thing.
@@jco1298 that is true J
Great job...well done 👌
Very Impressive, Awesome Details
Sapphire Cristal ?
Very clean job and well done, please where can I purchase the bezel insert please. I am in dire need of two inserts. Please hook me up. Thanks
Great job! Keep em coming.
Thanks Sosin, I appreciate it
how did you found again that little self propelled ring???
great job , but i noticed day wheel not positioned correctly , is this defect in miyota 8203 , i have same watch with exact problem ?????
Great job
Nice video. One question: Was the pressure-test procedure in the video meant as a joke to see anyone was paying attention? (You're supposed to release the pressure with the watch submerged to check for bubbles..).
The watch was submerged! Don’t understand what you mean. But for sure it was not a joke it was a test.
2 methods. 1 have it in the water and pump the pressure up. If it fills up its leaking (and damaged)
2 you have it above the water, pump up the pressure (if there are any leaks, the air pressure in the watch will go up) then lower it in the water and release the pressure valve. If there was a leak then this will show as bubbles from the effected area as the pressure in the tank becomes normal and the watch equalises with the outside pressure. This way when you find a leak, you can lift it up quick to save the watch.
yeah. the pressure test didn't look right to me either.... he released the pressure with the watch in the air.
I am literally wearing a more recent release of this watch at the time of typing this
Nice Job
Thanks!
Gran bel video e lavoro di restauro! Posso chiederti dove hai trovato le lancette?
May I know where u order the replacement parts? Thank u in advance!
Hello, could you tell me the reference of the crystal gasket please ? Thank you, and very nice video :)
Great video! Would love to see a side by side comparison at the end of the video of the beginning and final product to see the difference the restoration has made.
Do you have any openings for new customers?
Hallo,
erst einmal meinen Dank an Dich für Deine tollen Videos!
Aber eine Frage habe ich zu diesem Video hier:
Ziemlich am Ende des Videos machst Du einen Drucktest auf Wasserdichtigkeit mit der restaurierten Uhr.
Du baust Druck im Tester auf, senkst die Uhr in das Wasser ab, schreibst dann "No Bubble, No Trouble", hebst die Uhr wieder aus dem Wasser heraus und lässt (der Tonspur zufolge) DANN den Druck ab.
Müsstest Du nicht den Druck langsam ablassen _solange die Uhr noch unter Wasser ist_, um zu schauen ob DABEI (beim Ablassen des Drucks) Blasen aufsteigen?
Sie bei erhöhtem Aussendruck einfach einmal die Uhr einzutauchen und wieder herauszuholen sagt ja nichts aus…
Thought you cleaned the parts? Looks like there is more dirt and fingerprints on reassembly than before.
Question about this same model: mine stopped so I opened it to find that the pallet fork correctly engages the escape wheel but everything else is not moving as soon as I put back the bridge... Any advice?
Hi it can be a lot of things from a Brocken week tooth to a Brocken barrel spring. You have to inspect all the parts under microscope. If nothing is Brocken it should work after cleaning.
My first dive watch from a decent brand with some horological history was a Promaster Dive eco-drive. I’m looking for a Promaster automatic but to find one for sale is nigh impossible.
Not anywhere close to impossible as they are very common and easily accessible and available for sale all the time from many companies and individuals.
How were you able to remove the bezel? My NY bezel rotates great but I can't seem to remove it to change the insert.
where did you get the new handset?
buongiorno come si fa a ordinare quadrante e sfere citizen promaser cal 8200a
Tolle Arbeit. Woher bemmst du denn die Ersatzteile?
Funny .. Red Dead Restoration did this same model watch last year .. it had the same problem .. broken pivot on the pallet fork. Seems a common problem with this watch.
Where did you find the minute hands?? I cannot find anywhere to replace them.
Ebay
wow..noice!
anche io ho questo orologio,tutti gli anni di produzione hanno ingranaggi di plastica?
would you be able to do a video on a seiko 6139 or a seiko 7005?
I saw so much lint AFTER cleaning being put back together with lint still INSIDE "cleaned" watch!
I've just recently bought the fully lumed version of this watch. Unfortunately I noticed that the bezel is very slightly misaligned. I had considered sending it back but is it possible to remove the bezel and reseat it so that it lines up correctly?
Yes it might work but it is pretty difficult to take the bezel off when you don’t have the correct tool for it.
Excellent job but that chapter ring was way out of alignment at the end
Hey, i own a similar ny0080. I removed the bezel a while ago but i never manage to put it back in. I dont know where i could get the proper bezel wire for the case. I got one for a vostok but seems to be extremely difficult to sit in. I got a basic watch crystal press. Any advice?
You need to release the air while the watch is in the water too
How in the world do you know how to put that movement back together?!
Trying to Memorize. Taking pictures or watching the film again.
But you didn't show be side number how clean?
Colossal work!
Thank you 🙏
@@wristwatchobsession5585 Why u always wearing gloves?
So the movement, dial, etc doesn’t get my fingerprints.
Also I think it looks better than pink and white finger cots although finger cots are more comfortable to wear 🙂
@@wristwatchobsession5585 Thanks $-) If I buy watch from you, I want your fingerprint on the watch
Love it 😂😂😂. Thanks
Spettacolo ❤
I just noticed that red seconds hand. Could that be aftermarket? That's supposed to be an ISO Certified Diver's watch. Without lume on that seconds hand, it can't be.
Very good!
Thank you 🙏
Why did you pressure test it with the movement intact?
It doesn’t matter if it is intact or not. What is important is that no water goes inside. You don’t turn off your watch when you go diving or?
@@wristwatchobsession5585 No, but when you pressure test as a repair person, they typically keep the movement out during that step to ensure water resistence works, to protect the movement. If you treat it with a valuable movement inside and it gets wet, it could be trouble for you.
You left dust all through it.
No. He was in a negative pressure room
👏👏👏
Great job!
Thank you Farhad 🙏
wow
Citizen Vs Seiko: who wins?
Do you can help restaured my watch?
How much this watch?
top
I changed the Movement on my Promaster. The day on the display is slanted, can that correct it? Best regards
Thanks. Really enjoyed that.
You mean can that be corrected?
You mean the day disc is bent and you want to make it straight?
@@wristwatchobsession5585 I have installed the Miyota 8205, how can I correct the day where is inclined?
Roy I don’t exactly understand your problem.
Can you please send me a message and a photo on Instagram?
@@wristwatchobsession5585 ok, Thank you
Great bro
Thank you
@@wristwatchobsession5585 obliged bro
Interesting vid. My NY0086-86E runs not that accurate, it runs about 13 s/d to fast.
Where do you buy a new bezel?
Ebay
200 quid service on a 40 quid movement 😁
How much cost such a reparations?
For this watch around 100 euros.
The chapter ring is completely misaligned !
pressurize on air, depressurize underwater
Enjoyable video but I can't help but think that you did over $100 of work on a $30 movement thats not even rare.
That's not the point chuckles 🤡
You are doing wrong the water resistasce test my friend..
Explain why
This is not very dirty