HOW TO REGLAZE A BATHTUB #5 | Removing Paint from a Tub that has been Refinished before | DP Tubs
ฝัง
- เผยแพร่เมื่อ 3 ก.ย. 2020
- A full and in depth STEP-BY-STEP process of Bathtub Reglazing a cast iron bathtub. This bathtub has been painted or reglazed before and I take you step by step throughout the entire process of refinishing this bathtub. A full bathtub reglaze that includes stripping or removing the existing paint, acid wash and deep clean, Masking paper, and final spraying of the bathtub reglazing top coat with the Capspray HVLP Spray gun.
Spray Equipment used: Titan Capsrpay 75 and Maxim II spray gun
Tub Refinishing material: Krylon Tub and Tile 2 part 1:1 ratio
Stripping or Paint Remover: Jasco Paint and Epoxy Remover: amzn.to/3xniGik
Acid wash: NAPCO Ltd Pirhana Etch and Cleaner combo
Comment down below if you have any questions about the Bathtub Reglazing process!
Don't forget to SUBSCRIBE, LIKE, and COMMENT DOWN BELOW!!!
Products Used in Videos on this Channel:
Material Used:
Bondo Fiberglass Resin: amzn.to/3rneluX
Bondo Fiberglass Mat: amzn.to/3cLCiDp
Bondo Glass Short Strand: amzn.to/3xlYuh0
Ryobi Corded Drill: amzn.to/3xkf3K6
HDX Mixing Cup 32oz: amzn.to/3p0JD7L
2" Paint Brush 24pk: amzn.to/3nLdZMd
120 To 3000 Assorted Grit Sandpaper for Wood Furniture Finishing, Metal Sanding and Automotive Polishing, Dry or Wet Sanding, 9 x 3.6 Inch, 36-Sheet: amzn.to/312NYzi
Bondo Spreader Pack: amzn.to/3HNIEAJ
Bondo All-Purpose Putty: amzn.to/3CPE29p
Zinsser 1-2-3 Primer: amzn.to/3oXAmO2
Krylon Alternative: Rustoleum Tub and Tile White: amzn.to/3FFTcQi
Caulking DAP Stretch: amzn.to/30YsZhe
Napco Extra Strong Acid Etch: www.napcoltd.com/case-extra-s...
Jasco Paint and Epoxy Remover: amzn.to/3xniGik
Loctite Foam Gap Filler: amzn.to/3xkgTuu
Capspray Titan Compressor 75 / 95:
Titan 0524041 or 524041 Capspray Maxum II HVLP Spray Gun with Free Check Valve Kit 0297051: amzn.to/3CUJo38
3M Half Mask Reusable: amzn.to/3DSmomO
3M N95 Respirator Filter 10pk: amzn.to/3cNv9CI
3M Cartridge Replacement Pack: amzn.to/2ZpjhUq
Fume Exhauster 8" Duct Tubing: amzn.to/3cKe64v
Portable Ventilation Exhaust Fan here: amzn.to/3k5Gz5W - แนวปฏิบัติและการใช้ชีวิต
NIIICE!!! A “10” rating from 1-10. Great how to video. Very detailed and nothing left to chance. The finished product looked like it was a newly purchased/installed bathtub. Excellent. 👍🏽
I appreciate that!
@@DPTubs why didn't you sand after the acid wash?
Mesmerizing transformation! That is a lot of work, but such a dramatic difference.
What an amazing transformation thank you for sharing it's way better looking than what it was.
I had to come back and comment here because this video saved me. I spent a long first day super discouraged. Followed this exactly and it helped me remove the finish straight away. Wanted to help anyone else possibly doing the same. I'm so glad I didn't convince myself I couldn't do this. 🥲
If you're refinishing your own tub, do yourself a favor and get a paint sprayer. It can be done with the roller but it's challenging.
Also, consider that this might take you at least a couple days. I spent a whole long weekend doing this.
Thanks for posting this and helping me, OP!!
Thank you. Thank you. Thank you!
Great video. I transformed a claw foot tub. The key is the Jasco. There was only one can on the shelf - I got 90% done with that can in a hour. The next day it took 2 cans of goof off, 5 hours additional hours and much more elbow grease to finish the remaining 10% - man I wish there would have been a 2nd can of Jasco available. I would say the 2nd most important key is plenty of fresh scraper blades - they get dull pretty quickly - I went through about 10 of them, remember to flip them over and use both sides. Once I was like 98% done I used an electric sander with 80 grit and that got all the little remaining stuff fast and easy.
Thanks again, without this video the not for tubs warning on the Jasco would have scared me away from it.
We
great job!!!! sanding and cleaning are all. these dirty works you must follow. its the most time consuming part. nice step by step video
Wow!! love your instructions. Looks fabulous and hope I get the same result.
thank you so much for including the equipment you used!
Congratulations on the work! Very professional, neat, and satisfying.
Nice work! Super clean.
What a transformation! Awesome!
Yeah I like the white better than the Almond color!
After starting wrong kinda wrong I decided to watch videos (seems like 30 of them). This (and your other tub-strip vid) is the absolute BEST right down to the Jasco because my research says it's best but the product says not on tubs - Thanks for your input there, now I will usue it. Unfortunately, it's an RV tub and I grinded it down to (nevermind) before I learned just to sand. Thanks so much! I still might need to hire someone but I'll have that experience of knowledge in advance, if I do. Thanks again
Thank you for showing how to glaze a bath tub step by step!
What a good Job, looks like new 👏 ❤ love it
It’s nice to see someone take pride in their work!
Thank you for allowing me to watch you as you work and explain in details. Great job. I enjoyed the video. The music was A +
This was so cool to see . I was stuck on the screen in amaze. I dont know why but this was really satisfying to watch something ugly turn so beautiful. Thanks for sharing awesome job Danny.
Omg I couldn't of said it better! That's exactly what I was feeling
Wow, to see it step by step I know the questions to ask my contractor to verify he will be thorough. Thank you.
Glad it was helpful!
Enjoyed watching this!
Love this video. Amaze job Danny.
Definitely loving the series!
Thanks man...I have some fun video ideas coming up.
Beautiful job!
Nice work Danny
Awesome work
Looks really good
Great video 📹 very informative 👏 needed lighting 💡
Looks great 👍🏻💜
What a great job 👏👏 and great video! Thanks!
Thanks for watching Elisha
Great video. Thank You!!
Looks great
WOW! Beautiful Job 👍🏽🇨🇦
Great detailed Video
I like the spray better! I've used from Napco the brush on gel type stripper and they tell you to make "x's' on the paint with a utility knife before applying. So messy and I'm looking forward to trying your way next strip
Great job
Very nice job
Great Job
Wow amazing work
Thank you!
I'm gonna be doing this so thank you
Nice job I can see your a pro hope I can even get close
Well done
You did a wonderful job start to finish! Would you be able to tell me where I can locate the napco ltd piranha etch and cleaner combo?
Amazing! Totally love your work. I am planning on painting my kid's tub, its an old ugly green, can this remover do the job?
Just beautiful. Thanks for sharing. I will be looking forward to your next video until then I am keeping you and your's in my thoughts and prayers please stay safe, take care and God bless!
one of the best jobs I've seen, congratulations, one question: what type of primer do you use?
Do the cleaning products affect the grout or metal like the drain for example ? To prorect and maintain the shine of the new coating, what cleaning products are best to use on it and what not to use at all?
Dang!!!
This is a lot of work
Thought i could DIY this until i saw the paint sprayer LOL I’ll hire someone
Hi. great video. how do you scrape the four inside corners in the tub? they're too concave for blade. Thanks.
Do you use a tac cloth to prevent dust particles from getting in the finish?
That’s cool
Looks lovely, I just ordered the Jaso Paint and Epoxy remover. I can't find NAPCO Ltd Pirhana Etch and cleaner combo? any other suggestions to acid wash and dull the surface?
Great video! How many paint coats you applied? How much time in between coats? Can a roller be used instead? Pros and Cons? Thanks
Well Sir.. how many and how long in between. There's no responses to these questions in comment
The best
Thanks to your step by step video, I feel so confident with fixing our bathtub now! Thank you!
Previous tenant also painted over the white subway bathroom wall tiles. How do you suggest I strip the paint without damaging the tile glaze? Thanks 🙏🏼
The same way
Great videos! I was wondering if I use Jasco on my tub could I not reglaze with it if I liked the original tub.
Thx
Your video gave me the confidence to attempt to diy it. Thanks for these gems. Shit I'd hire you to come do it.... chances you live in central FL are slim. I'll have to get my supplies tomorrow
Do it! Let me know if you have any questions!
Wow..😮❤❤❤
Wow!!
good video. hope you can help me with a question? had tub resurfaced a couple years ago. i used an ardex silicone caulk and within a couple month turned yellow. have been putting the project off because i am scared to remove the caulk, not knowing how careful i have to be to not mess up the resurfaced tub? they gave instructions on cleaning it and a list of approved cleaners. i know i can't use a caulk remover on it because that stuff is harsh, any ideas? thanks.
Hi can you tell me what product you use to glaze and what setup as far as tools go when spraying
Will the sanding and spraying the stuff on work if I just want to remove the cheap paint the old sellers painted our tub with? They put some sort of smooth coating on in some areas but abrasive paint in others. I just want to recover the tub underneath, that's all, no repainting.
is there any way to remove "drips" off of a previously reglazed tub without reglazing the entire tub?
My bath tub is one of those kits and when i first moved in i sprayed it with rustoleim paint to cover scuffed spots it doesn’t allow my shower mats to stick. Do you have a video or instructions on reglazing those bathroom kit bathtubs
Boss quick question. Do you use a primer before go to epoxy and spray the tub?
Can I use just the spray can of Krylon Tub and Tile - I don't have a machine... I also know that there is one with a wider spray top but I cant find that so I just got regular can.
Can you use an orbital sander? What paper woukd you recvomend?
Does removing reglazing from a steel bathtub damage it so it has to be reglazed again or can you just leave it off?
hello is there a specific spray gun to use when putting down the glaze?
What cleaning supplies and brusg would you recommend to prevent this from happening again??
Thank you, DP. It is a professional job. Question, When do you remove the protective tape from the drain hall? After completely dry, or right after spraying finished? And how?
I donut right after but you could also remove it after it dries to be safe not to touch anything when wet. Poke a hole in the middle and then peel off from the center out.
@@DPTubs So you do remove it right after ?? or you wait until it is dry??
Hello DP, I am wondering what product you sprayed as the finish. Thx.
If paint remover gets on grout will it ruin it? I have a tub sink and wall to do. The wall is old tile with the grout
Excellent video. Thanks!
Do you ever get to Michigan? 😃
Maybe one day!
great work ! what do you use to reetch the non slip etching to the floor of the tub
If the customer wants they have an option for a non skid coating application. I use shark grip
Wow this is great- I am a complete Novice and want to fix my kids Tub. It looks like I may have to rent a few tools like that glaze spray or can I just paint it on ?
I have some scratches on my new tub after remodeling.
How can I get them off?
Thank you 😊
Great videos and I'm trying to refinish my tub. Do you have a video where you don't not use a spray device? Something with a roller maybe?
I have the same question
@@dennisjenkins4987 I don’t show a roller because I would never use one. Messy, inconsistent finish, IMO! There are definitely some DIYers who would use it and that’s totally fine because the spray gun could get pricey. You could use a spray can Homax and they have an attachment that will allow you to spray the can like a gun.
Check out my latest video as yiu could see me use it when I spray the primer around the perimeter of the tub.
When he says re-glaze, does he mean it will be as if it were a new tub like the porcelain feeling in stead of the ruff paint feeling. When you re-glaze will it peel ?
Loved it. YOU'RE A PRO!
Danny how long does it take you to do a job like this from start to finish?
With stripping or removing an old coating it will take about 4-5 hours
How much extra do you charge for this type of scraping. I seen you charge $300 for the reglazing but this seems like a pain
Boomanik Boomerangs the stripping is an extra $75-$100
How to find the scrapper you used? Did you do just one coat of spray,
Love your Videos! Can you tell me what size tip you are using with your gun (Capsrpay HVLP Maxum II)? Is it the stock tip that comes with the gun?
Yes a #3
What paint to use for bath tubs
Hello. How long does it take to dry?
Great video! What kind of primer and epoxy paint did you use, for someone that has a paintgun? Also how long did you wait between coats?
I wait 10 minutes between first and second. 12 minutes between second and third
You doing your thing, great video! How long does this last after finished?
With proper care 5 years plus.
Is there a top coat to use to make it so shiny
Great work! Any advice on how to remove your stains from an old cast iron tub?
Try water and 800 grit wet dry sand paper...if that doesn’t work try a little lacquer thinner and sand paper to see if that works.
@@DPTubs i will try that, thank you!
Nice!what is the product you use ?
Awesome job!!!
What kind of primer brand do you use on fiberglass tubs. Thank you.
Professional grade I use Resurface Solutions Euro Epoxy.
What exactly brand and type of paint you using, please let me know I'm just waiting to mine but I'm not sure what kind of paint I need
is there a liquid you can use to paint on instead of spray on?
How can I patch a crack in a tub with a textured bottom and keep the textured look and feel over the patch?
Awesome job man👍🏾 what tip size did you use on your Maxum II gun?
3
Just want to clarify - what you put in the Capspray is the Kyrlon Tub and tile 2, right? Thanks so much for the products and the video. Amazing transformation
Yes for DIY users I would recommend Krylon Tub and Tile...for professional Resurface Solutions
@@DPTubs where to purchase the professional resurface solutions?
Great job mate...What did you charge for this job. Thanks from NZ
Which HVLP do you use make a review
Hey DP, what filter are you using in the half-mask your wearing? Do you ever use an assisted air machine when spraying or just the 3M filter mask? Thanks for putting out these great videos!
Cory Dinell I have an 8” diameter fume extractor and hose that I use. I will show a video of it. Helps with overspray, VOCs, and primer dry times / moisture
Hey Danny, we had our tub sprayed and noticed the mist travelled into various parts of our bedroom. There is a white mist on our laminate now. We tried everything including paint thinners to remove it but no luck. Can you recommend something to clean up this mist on the floor? Thanks so much!
This is my recommendation: I would use lacquer thinner. It’s different than paint thinner. Try a spot with lacquer thinner and maybe a blue non scratch pad from the cleaning aisle at Home Depot and test a small area. If it’s on glass or a hard surface I would carefully use a single edge blade to scrape it off carefully. Do not use lacquer thinner or blade on wood flooring or cabinets. Always try a small area first. Also, have you contacted the person who did it?
How come the jasco can says not to use it on tubs?? Curious
How much do you charge for the stripping of paint? Then how much for the whole job?
so what primer and paint are you using ??