How To Rebuild Yamaha V6-V4 2 Stroke Carburetor.

Here we are pulling apart a 2 stroke carburetor V6-V4 Yamaha cleaning it and showing some things I look for. Just a note before I put it back together I used compressed air and blew thru all the passages of the carburetor. Coming up next we are doing the same on a 2 stroke 90 Yamaha
This is the same carb used on a Yamaha 115 hp Yamaha 130 hp Yamaha 150 hp Yamaha 175 hp Yamaha 200 hp
And as an added bonus I show the page from Yamaha discontinued tune up book for the 150 hp specks including the carburetor pilot screws.

[@martinkoche4375]

Thank you

[@dsmenterprises6699]

I check all the mixture adjustments screws if I did not have a manufacturer spec on them but it is not the gospel sometimes as the motors age and our fuel changes so will the tuning of the carburetor. As for the measurements on the float I have been doing this since 1990 and have never really seen a benefit of going that extreme on the float measurements I like to get them so that the bowel is full of fuel

[@tyyoung3698]

Wow, what a great video. Thank you. My confidence is soaring at this point. I feel like the investment in a small ultrasonic parts cleaner is worth it -- right ?

[@dsmenterprises6699]

It will help but a good cleaning solution with compressed air due the job most of the time.

[@Raman382cig]

The 130 beto looks like the same carburetor. U know how there must must place the screw for perfekt engine run?

[@bimmerwman]

Do you know if the screws are JIS or regular Phillips head? Thanks for the Video!!

[@Fpvcandy]

Man this is my main question that no one is ever %1000 clear on...
On this model carb how many fuel mix screws need to be counted per revolution as they are taken out? Only 1 correct? Per carb? I usually put a digital caliper on the floats before removing them to get an exact reading on the measurement they sit at so I can match it when I put the bulb back in. Would you consider this good practice or waste of time?

[@carlospadilla9576]

The little plate either the gasket. There are two air jets is there a way you put them in

[@alexwallace8573]

What is the factory idle mixture setting for a 1992 txrq 200?

[@andrewjernigan799]

Hey I have a late 80s Yamaha pro v 150 2 stroke I just replaced both fuel pumps after I replaced them it seems to be running super rich is there a way to lean is out so it won’t be smoking as much before I replaced the pumps it was barely smoking only when first started any ideas

[@dsmenterprises6699]

Check your oil pump rod when the throttle is set adjust the oil rod until it is close to the sop pin

[@diveandrelaxlanta]

Can you let us know what you used in the ultrasonic cleaner?

[@dsmenterprises6699]

Yes 2 parts distilled water and one part simple green. I use the lemon scent. On a side note my machine holds about 3 gallons and I will also put a small amount of dawn dish soap in the water, Never leave carburetors in the ultrasonic machine for more than 15 min it can damage the finish on the carburetor so keep an eye on them as you go.

[@OGAstra]

whats the best place to order genuine yamaha carb kits and impeller kit? yamaha 175hp 2 stroker

[@dsmenterprises6699]

Partsvu

[@timtiffany4302]

How do you ajust the carbs..my 200

[@dsmenterprises6699]

What model and year

[@abdulla9869]

Hi how are you

[@alexebis9237]

Hi

[@georgenettlesjr1466]

How to mail you mine?

[@dsmenterprises6699]

I can do that but would suggest you try and look for someone local to you that is qualified. And I am booked until July 12

[@blessingD-dy7fo]

I need a job I'm yamaha expert